Ubiquiti UniFi Stadium XG Bedienungsanleitung

Quad-Radio 802.11ac

Wave 2 Access Point with

Dedicated Security and

Beamforming Antenna

Model: UAP-StadiumXG

Introduction

Thank you for purchasing the Ubiquiti Networks®

UniFi®Quad‑Radio 802.11ac Wave 2 Access Point with

Dedicated Security and Beamforming Antenna. This Quick

Start Guide is designed to guide you through installation and

includes warranty terms.

IMPORTANT: The UAP‑StadiumXG requires the UniFi

Controller v5.7 or higher, available at:

www.ubnt.com/download/unifi

Package Contents

UniFi Stadium XG AP Adjustment Bracket

Pole Clamp Carriage Bolts

(Qty. 4)

Flange Nuts

(Qty. 4)

Quad-Radio802.11ac

Wave2 Access Point with

DedicatedSecurity and

BeamformingAntenna

Model:UAP-StadiumXG

Lag Screws

(Qty. 4)

Gigabit PoE

(50V, 1.2A)

Power Cord Quick Start

Guide

cable and earth grounding must be used as conditions of product warranty. TOUGHCable™ is

designed for outdoor installations. It is the professional installer’s responsibility to follow local

country regulations, including operation within legal frequency channels, output power, and

Dynamic Frequency Selection (DFS) requirements.

Installation Requirements

• 13 mm wrench

• Cat5/6 UTP cable for indoor installations

Outdoor Installation Requirements

• Shielded Category 5 (or above) cabling with should be used

for all outdoor wired Ethernet connections and should be

grounded through the AC ground of the PoE.

We recommend that you protect your networks from

harmful outdoor environments and destructive ESD events

with industrial‑grade, shielded Ethernet cable from Ubiquiti

Networks. For more details, visit: www.ubnt.com/toughcable

System Requirements

• Linux, MacOSX, or Microsoft Windows 7/8/10

• Java Runtime Environment 1.8 or above recommended

• Web Browser: Google Chrome (Other browsers may have

limited functionality.)

• UniFi Controller software v5.7 or newer (available at:

www.ubnt.com/download/unifi)

Network Topology Requirements

• A DHCP‑enabled network (for the AP to obtain an IP address

as well as for the wireless clients after deployment)

• A UniFi Cloud Key or management station running the UniFi

Controller v5.7 (or newer) software, located either on‑site

and connected to the same Layer 2 network, or off‑site in the

cloud or NOC

USG-XG-8

(DHCP Server)

US-16-XG

Internet

UAP-StadiumXG

LAN

WAN

Remote Access to

UniFi Controller

UAP-XG

UAP-StadiumXG

UniFi Hybrid

Cloud Install

DOWNLOADTHROUGHPUT&LATENCY DEVICESON2.4GHZCHANNEL

DEVICESON5GHZCHANNEL

UPLOADTHROUGHPUT&LATENCY

LATENCY THROUGHPUT

SPEEDTEST

msec Mbps

7 0.94 1

2.33

25 22

597

0.9 116

200+0700+0

0.01 413

2290.2

2118

547

ACTIVEDEVICE

WAN

Inacve 0

Pending

Inacve 0

Pending

ACTIVEDEVICES

Inacve 0

Pending

118

ACTIVEDEVICES

LAN WLAN

DEEPPACKETINSPECTIONCLIENTSDEVICES

250

200

150

100

24HRS 12HRS NOW

Avg/MaxThroughput Latency

Latency[msec]

Throughput[Mbps]

100

24HRS 12HRS NOW

Latency[msec]

Throughput[Mbps]

NetworkProtocols

StreamingMedia

Web/Web2.0

FileTransfer

SocialNetwork

Other

Motorola

Lenovo

SamsungE

Dell

Acer

Other

WLAN

LAN

WAN

118

582GB

23.3GB

22.7GB

8.47GB

3.6GB

5.46GB

258

241

220

213

130

110

126

DEVICES

645GB

TRAFFIC

1172

CLIENTS

1 2 3 4 5 6 7 8 9 10 11

36 40 44 48 52 56 60 64

100 104 108 112 116 120 124 128

132 136 140 144 149 153 157 161 165

CURRENTSITE

Default

USERNAME

admin

Sample Network Diagram

All UniFi devices support off‑site management controllers. For

setup details, see the User Guide on the website:

www.ubnt.com/download/unifi

Hardware Overview

Top View

Adjustment Bracket

Pole Clamp

Lanyard Loop

Mounting Bolt

Elevation Lock Bolt

LED

The RGB LED is set to the factory defaults below; however, the

color and lighting pattern are software‑controllable.

LED Color Status

White Factory default, waiting to be integrated.

Flashing White Initializing.

Alternating

White/Blue

Device is busy; do not touch or unplug it.

This usually indicates that a process such

as a firmware upgrade is taking place.

Blue

Indicates the device has been successfully

integrated into a network and is working

properly.

Quickly

Flashing Blue

This is used to locate an AP.

When you click Locate in the UniFi

Controller software, the AP will flash. It

will also display the location of the AP on

the map.

Steady Blue

with Occasional

Flashing

Indicates the device is in an isolated state

(all WLANs are brought down until an

uplink is found).

Ports

Reset

Button

10 GbE

Port

1 GbE

Port

10 GbE The 10 GbE port is a 1/10 Gbps Ethernet port used to

connect to the LAN and DHCPserver. It can also be used to

connect the power.

Note: The UAP‑StadiumXG can be powered using an

802.3bt PoE switch or the included Gigabit PoE adapter.

For instructions, see Powering the UniFi AP.

1 GbE The 1 GbE port is a 10/100/1000 Ethernet port used for

bridging. It can also be used to connect the power.

Reset The Reset button serves two functions for the

UAP‑StadiumXG:

• Restart Press and release the Reset button quickly.

• Restore to Factory Default Settings Press and hold the

Reset button for more than five seconds.

VESA Mounting

If you choose to use your own mount, remove the four M4 x 10

screws from the back of the UAP‑StadiumXG and detach the

pre‑installed mount.

The 8‑hole mounting pattern on the back of the

UAP‑StadiumXG follows the VESA MIS‑D standard and can be

used with mounts that comply with this standard. Use either

the 100 x 100 mm or 75 x 75 mm square hole pattern with

M4x 10 screws.

75 mm

100 mm

*640-00357-01*

640-00357-01

Hardware Installation

The UAP‑StadiumXG can be mounted on a pole or wall.

Proceed to the appropriate instructions for your installation.

Pole Mount

1. Attach the Pole Clamp to the Adjustment Bracket.

a. Hold the Adjustment Bracket with its clamps facing you.

b. Insert the Carriage Bolts through the rectangular holes

of the Adjustment Bracket.

c. Slide the single hole of the Pole Clamp over the

corresponding Carriage Bolt.

d. Place one Flange Nut on each bolt.

Pole Clamp

Hole

2. Mount the Adjustment Bracket on the pole and secure it.

a. Place the Adjustment Bracket against the pole.

b. Slide the three slots of the Pole Clamp over the

corresponding Carriage Bolts.

c. Tighten the Flange Nuts of the bolts to 25 N· m to secure

the Adjustment Bracket to the pole.

25 N · m

Note: The mounting assembly can accommodate a

Ø 25.4 ‑ 50.8 mm pole.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Ubiquiti Drahtloser Zugangspunkt Handbücher

Ubiquiti

Ubiquiti UniFi nanoHD Bedienungsanleitung

Ubiquiti

Ubiquiti Rocket R5AC-Lite Bedienungsanleitung

Ubiquiti

Ubiquiti Bullet M5 HP Bedienungsanleitung

Ubiquiti

Ubiquiti PowerBeam PBE-5AC-400-ISO Bedienungsanleitung

Ubiquiti

Ubiquiti AirFiber X AF-5G34-S45 Bedienungsanleitung

Ubiquiti

Ubiquiti airFiber AF-11 Bedienungsanleitung

Ubiquiti

Ubiquiti UniFi UAP-IW-HD Bedienungsanleitung

Ubiquiti

Ubiquiti UniFi UAP-FlexHD Bedienungsanleitung

Ubiquiti

Ubiquiti IsoStation AC IS-5AC Bedienungsanleitung

Ubiquiti

Ubiquiti Rocket M3 Bedienungsanleitung

Ubiquiti

Ubiquiti NanoStation M Bedienungsanleitung

Ubiquiti

Ubiquiti UniFi Bedienungsanleitung

Ubiquiti

Ubiquiti NBE-5AC-Gen2 Bedienungsanleitung

Ubiquiti

Ubiquiti QCA9994 Anwendungshandbuch

Ubiquiti

Ubiquiti UniFi AP AC Lite Bedienungsanleitung

Ubiquiti

Ubiquiti NanoStation NSM365 Bedienungsanleitung

Ubiquiti

Ubiquiti NBE-5AC-Gen2 Bedienungsanleitung

Ubiquiti

Ubiquiti Uni-fi AP Bedienungsanleitung

Ubiquiti

Ubiquiti UAP-AC-M Bedienungsanleitung

Ubiquiti

Ubiquiti U-Installer Bedienungsanleitung

Ubiquiti

Ubiquiti Rocket Prism AC GEN 2 RP-5AC-Gen2 Bedienungsanleitung

Ubiquiti

Ubiquiti M900 Bedienungsanleitung

Ubiquiti

Ubiquiti GigaBeam GBE Bedienungsanleitung

Ubiquiti

Ubiquiti Lite Beam AC LR LBE-5AC-LR Bedienungsanleitung

Beliebte Drahtloser Zugangspunkt Handbücher anderer Marken

D-Link

D-Link DWL-2100AP - AirPlus Xtreme G Bedienungsanleitung

Cisco

Cisco Aironet 1550 Series Bedienungsanleitung

Aruba

Aruba IAP-335 Bedienungsanleitung

Advantek Networks

Advantek Networks AWN-AP-54MR Bedienungsanleitung

IP-COM

IP-COM AP355 Bedienungsanleitung

Buffalo

Buffalo AirStation WLA-L11G Bedienungsanleitung

EnGenius

EnGenius EnStationACv2 Bedienungsanleitung

D-Link

D-Link DAP-3662 Bedienungsanleitung

Widelink

Widelink ezWave WAP-1100 Series Bedienungsanleitung

Edimax

Edimax CAP1200 Bedienungsanleitung

xG Technology

xG Technology xMax CN1300 Bedienungsanleitung

Aruba

Aruba AP-203R Bedienungsanleitung

LuXout Shades

LuXout Shades LUXSHADE MOTION Bedienungsanleitung

CreatComm

CreatComm TB5F Bedienungsanleitung

SineDigital

SineDigital MW-1500AP(H) Bedienungsanleitung

TP-Link

TP-Link AP9650 V1 Bedienungsanleitung

Draytek

Draytek VIGORAP 902 Bedienungsanleitung

EnGenius

EnGenius EAP350 Bedienungsanleitung