Ubiquiti UniFi UAP--AC--HD Bedienungsanleitung

802.11ac Wave 2

Enterprise Wi-Fi Access Point

Model: UAP-AC-HD

Introduction

Thank you for purchasing the Ubiquiti Networks®

UniFi®802.11ac Wave 2 Enterprise Wi-Fi Access Point.

This Quick Start Guide is designed to guide you through

installation and includes warranty terms.

IMPORTANT: The UAP-AC-HD requires the UniFi Controller

v5.3 or newer, available at: downloads.ubnt.com/unifi

Package Contents

UniFi AP AC HD Mounting Bracket Ceiling Backing Plate

Flat Head Screws

(Qty. 4)

Keps Nuts

(Qty. 4)

Screws

(Qty. 4)

Screw Anchors

(Qty. 4)

802.11ACWave 2

AccessPoint

Model:UAP-AC-HD

Gigabit PoE* (48V, 0.5A)

with Mount Bracket

Power Cord* Quick Start

Guide

* Included only in the single-pack of the UAP-AC-HD

cable and earth grounding must be used as conditions of product warranty. TOUGHCable™

is designed for outdoor installations. It is the customer’s responsibility to follow local country

regulations, including operation within legal frequency channels, output power, and Dynamic

Frequency Selection (DFS) requirements.

Installation Requirements

• Phillips screwdriver

• Drill and drill bit (6 mm for wall-mounting or 3 mm for

ceiling-mounting)

• Optional: Drywall or keyhole saw (to cut 18 mm hole for

Ethernet cable feed)

• Cat5/6 UTP cable for indoor installations

Outdoor Installation Requirements

IMPORTANT: The UAP-AC-HD may be installed outdoors

under an eave or other protected location. Do not

install the UniFi AP in an open environment.

• Mounting location should be at least 60 cm (2 ft) from the

edge of the eave or ceiling.

• Cable feed opening must be directed away from the open

environment.

• Cable feed must be pointed downwards when wall-mounted.

• Shielded Category 5 (or above) cabling should be used

for all outdoor wired Ethernet connections and should be

grounded through the AC ground of the PoE.

We recommend that you protect your networks from

harmful outdoor environments and destructive ESD events

with industrial-grade, shielded Ethernet cable from Ubiquiti

Networks. For more details, visit

www.ubnt.com/toughcable

System Requirements

• Linux, MacOSX, or Microsoft Windows 7/8/10

• Java Runtime Environment 1.6 (1.8 or newer recommended)

• Web Browser: Google Chrome (Other browsers may have

limited functionality.)

• UniFi Controller software v5.3 or newer (available at:

downloads.ubnt.com/unifi)

Network Topology Requirements

• A DHCP-enabled network (for the AP to obtain an IP address

as well as for the wireless clients after deployment)

• A UniFi Cloud Key or management station running the UniFi

Controller v5.3 (or newer) software, located either on-site

and connected to the same Layer 2 network, or off-site in the

cloud or NOC

US-16-150W

USG-PRO-4

(DHCP Server)

Internet

UAP-AC-HD

UAP-AC-M-PRO

UAP-AC-PRO

LAN

WAN

UniFi Hybrid

Cloud Install

Remote Access to

UniFi Controller

Sample Network Diagram

All UniFi devices support off-site management controllers.

For setup details, see the User Guide on the website:

documentation.ubnt.com/unifi

Hardware Overview

LED

LED Color Status

White Factory default, waiting to be integrated.

Flashing White Initializing.

Alternating

White/Blue

Device is busy; do not touch or unplug it.

This usually indicates that a process such

as a firmware upgrade is taking place.

Blue

Indicates the device has been successfully

integrated into a network and is working

properly.

Quickly

Flashing Blue

This is used to locate an AP.

When you click Locate in the UniFi

Controller software, the AP will flash. It

will also display the location of the AP on

the map.

Steady Blue

with occasional

flashing

Indicates the device is in an isolated state

(all WLANs are brought down until an

uplink is found).

Ports

Main

Port

Secondary

Port

Security

Slot

Reset

Button

USB 3C

Port

Reset The Reset button serves two functions for the UniFi AP:

• Restart Press and release the Reset button quickly.

• Restore to Factory Default Settings Press and hold the

Reset button for more than five seconds.

USB 3C The USB 3C port is reserved for future use.

Secondary The Secondary port is a Gigabit Ethernet port used

for bridging.

Main The Main port is a Gigabit Ethernet port used to

connect the power and should be connected to the LAN and

DHCPserver.

IMPORTANT: The UAP-AC-HD cannot be powered by the

US-8 or US-8-60W; however, it can be powered by other

UniFi PoE Switches that provide 802.3at PoE+power.

Note: If you need to remove the UniFi AP from the

Mounting Bracket, insert a straightened paper clip in the

Security Slot to release the Lock Tab and turn the UniFi

AP counterclockwise.

Upgrade from UAP-AC-PRO

The UAP-AC-HD uses the same mounting hardware as the

UAP-AC-PRO, so you only need to remove the UAP-AC-PRO

and replace it with the UAP-AC-HD.

To begin the upgrade, perform the following steps:

1. Insert a straightened paper clip into the UAP-AC-PRO

Security Slot to disengage the lock. Then turn the

UAP-AC-PRO counterclockwise and lift it off of the

mounting bracket.

Security Slot

UAP-AC-PRO (wall mount installation)

2. Unplug the Ethernet cable from the Main port.

3. Go to step 4 of the Wall Mount section or step 5 of the

Ceiling Mount section.

Hardware Installation

The UniFi AP can be mounted on the wall or ceiling. Perform

the steps for the appropriate installation:

Wall Mount

1. Position the Mounting Bracket at the desired location on

the wall with the Arrow pointing up.

2. Mark the four mounting holes, and use a 6 mm drill bit to

drill the holes. If your Ethernet cable feeds through the

wall, cut or drill a circle approximately 18 mm in diameter.

Then feed the CAT5/6 cable through the hole.

Arrow

Optional 18 mm Hole for

Ethernet Cable Feed through the Wall

3. Insert the Screw Anchors into the holes. Secure the

Mounting Bracket to the wall by inserting the Screws into

the anchors.

4. Remove the rubber port cover from the UniFi AP.

5. If the Ethernet cable is fed through the wall, skip to step6.

If the Ethernet cable runs along the mounting surface,

remove the cable feed plug.

6. Feed the Ethernet cable through the port cover.

Note: The feed hole will stretch to accommodate the

RJ45 connector, and then seal around the cable.

7. Connect the Ethernet cable to the Main port and replace

the port cover.

Andere Handbücher für UniFi UAP--AC--HD

Inhaltsverzeichnis

Andere Ubiquiti Drahtloser Zugangspunkt Handbücher

Ubiquiti

Ubiquiti UAP-AC-PRO-5 Bedienungsanleitung

Ubiquiti

Ubiquiti IS-5AC Bedienungsanleitung

Ubiquiti

Ubiquiti UniFi AP AC Lite Bedienungsanleitung

Ubiquiti

Ubiquiti PowerBeam AC PBE-5AC-620 Bedienungsanleitung

Ubiquiti

Ubiquiti GBE Bedienungsanleitung

Ubiquiti

Ubiquiti Edge Point EP-R8 Bedienungsanleitung

Ubiquiti

Ubiquiti RP-5AC-Gen2 Bedienungsanleitung

Ubiquiti

Ubiquiti UniFi nanoHD Bedienungsanleitung

Ubiquiti

Ubiquiti LiteBeam LBE-5AC-16-120 Bedienungsanleitung

Ubiquiti

Ubiquiti NBE--2AC--13 Bedienungsanleitung

Ubiquiti

Ubiquiti Rocket Prism AC GEN 2 RP-5AC-Gen2 Bedienungsanleitung

Ubiquiti

Ubiquiti NanoStatonM Series Bedienungsanleitung

Ubiquiti

Ubiquiti LTU-LR Bedienungsanleitung

Ubiquiti

Ubiquiti airCube ISP Bedienungsanleitung

Ubiquiti

Ubiquiti UAP-Outdoor-5 Bedienungsanleitung

Ubiquiti

Ubiquiti Rocket R5ACL Bedienungsanleitung

Ubiquiti

Ubiquiti BulletM2-HP Bedienungsanleitung

Ubiquiti

Ubiquiti AirMax AC Bedienungsanleitung

Ubiquiti

Ubiquiti PowerBeam M Bedienungsanleitung

Ubiquiti

Ubiquiti UniFi AC Mesh Bedienungsanleitung

Ubiquiti

Ubiquiti LTU-Lite Bedienungsanleitung

Ubiquiti

Ubiquiti NanoBridge M5 Bedienungsanleitung

Ubiquiti

Ubiquiti AmpliFi MeshPoint HD Bedienungsanleitung

Ubiquiti

Ubiquiti Bullet M5 HP Bedienungsanleitung

Beliebte Drahtloser Zugangspunkt Handbücher anderer Marken

D-Link

D-Link DWL-2100AP - AirPlus Xtreme G Bedienungsanleitung

Cisco

Cisco Aironet 1550 Series Bedienungsanleitung

Aruba

Aruba IAP-335 Bedienungsanleitung

Advantek Networks

Advantek Networks AWN-AP-54MR Bedienungsanleitung

IP-COM

IP-COM AP355 Bedienungsanleitung

Buffalo

Buffalo AirStation WLA-L11G Bedienungsanleitung

EnGenius

EnGenius EnStationACv2 Bedienungsanleitung

D-Link

D-Link DAP-3662 Bedienungsanleitung

Widelink

Widelink ezWave WAP-1100 Series Bedienungsanleitung

Edimax

Edimax CAP1200 Bedienungsanleitung

xG Technology

xG Technology xMax CN1300 Bedienungsanleitung

Aruba

Aruba AP-203R Bedienungsanleitung

LuXout Shades

LuXout Shades LUXSHADE MOTION Bedienungsanleitung

CreatComm

CreatComm TB5F Bedienungsanleitung

SineDigital

SineDigital MW-1500AP(H) Bedienungsanleitung

TP-Link

TP-Link AP9650 V1 Bedienungsanleitung

Draytek

Draytek VIGORAP 902 Bedienungsanleitung

EnGenius

EnGenius EAP350 Bedienungsanleitung