Uplus Lighting MIX560 Bedienungsanleitung

User manual

MIX560

Please read the instructions carefully before use

TABLE OF CONTENTS

1. Safety Instructions……………………………………………………………………………3-4

Technical Specifications…………………………………………………………………………4

Control Menu ……………………………………………………………………………………4-7

DMX Channels …………………………………………………………………………………7-10

Trouble Shooting…………………………………………………………………………………11

Fixture Cleaning………………………………………………………… ………………………11

STATEMENT

The product has well capability and intact packing when leave factory. All of the user should

comply with warning item and manual, any misuse cause of the damages are not included in our

guarantee, and also can not be responsible for any malfunction & problem owing to ignore the

manual.

1.Safety Instructions

Please keep this User Guide for future consultation. If you sell the unit to another user, be sure that

they also receive this instruction booklet.

•Unpack and check carefully there is no transportation damage before using the unit.

•Before operating, ensure that the voltage and frequency of power supply match the power

requirements of the unit.

•It’s important to ground the yellow/green conductor to earth in order to avoid electric shock.

•The unit is for indoor use only. Use only in a dry location.

•The unit must be installed in a location with adequate ventilation, at least 50cm from adjacent

surfaces. Be sure that no ventilation slots are blocked.

•Disconnect main power before replacement or servicing.

•Make sure there are no flammable materials close to the unit while operating as it is fire hazard.

•Use safety cable when fixes this unit. DO NOT handle the unit by taking its head only, but always

by taking its base.

•Maximum ambient temperature is Ta: 40℃. DO NOT operate it where the temperature is higher

than this Unit surface temperature may reach up to 85℃. DO NOT touch the housing bare-hand

during its operation. Turn off the power and allow about 15 minutes for the unit to cool down before

replacing or serving.

•the event of serious operating problem, stop using the unit immediately.Never try to repair the unit

by yourself. Repairs carried out by unskilled people can lead to damage or malfunction. Please

contact the nearest authorized technical assistance center. Always use the same type spare parts.

•DO NOT touch any wire during operation as high voltage might be causing electric shock.

Warning:

•To prevent or reduce the risk of electrical shock or fire, do not expose the unit to rain or moisture.

•The housing, the lenses, or the ultraviolet filter must be replaced if they are visibly damaged.

Caution:

•There are no user serviceable parts inside the unit. DO NOT open the housing or attempt any

repairs yourself. In the unlikely event your unit may require service, please contact your nearest

dealer.

Installation:

•The unit should be mounted via its screw holes on the bracket. Always ensure that the unit is firmly

fixed to avoid vibration and slipping while operating. And make sure that the structure to which you

are attaching the unit is secure and is able to support a weight of 10 times of the unit’s weight. Also

always use a safety cable that can hold 12 times of the weight of the unit when installing the fixture.

•The equipment must be fixed by professionals. And it must be fixed at a place where is out of the

touch of people.

2.Technical Specifications

Voltage：AC100~240V 50/60HZ

Power consumption:500W

Led source: 5*60W RGBW LED

Strobe face: 96 pcs 7070 led with 12 sections + 72 pcs 5050 led with 6 sections

Pan & Tilt 360°no limited rotating

Zoom angle: 2.5-45°

Channel:33/53/69/105 CH

Dimming:32bit 0~100% linear dimming

Control mode: DMX512/ Music mode/ RDM

Working temperature:-30℃~50℃

Strobe frequency:1~30HZ

IP rating:IP20

Carton size:60*42*28cm

Gross weight:15kg

3.Control Menu

Menu Operation

Menu key:enter/return to the main menu

Up key: menu function up selection/Parameter increment

Down key：menu function down selection/parameter decrement

Enter key：Select the menu function, and confirm and save when the menu function parameters are modified.

Main Menu

Submenu

Menu Function Description

1. System

settings

2. Operating

mode

3. Manual

control

1. DMX

Address

Modify the DMX address code up or down (the address code can be selected

from 001-512), and press OK to save it. The default is 001.

2. Encoder

Modify the encoder on/off upward or downward, and save the confirmation key,

which is on by default.

3. X Reverse

Modify X up or down to turn it on/off. Press OK to save it. It is off by default.

4. Y Reverse

Modify Y upward or downward to turn it on/off. Press OK to save. It is closed by

default.

1. System

settings

2. Operating

mode

1. Operating

mode

Select up or down the operation mode DMX/voice control/auto, confirm to save,

default DMX.

2. Channel

selection

Select channels CH33, CH53, CH69, CH105 up or down, and press OK to save.

The default is CH33.

3.Manual

control

1. X axis

Modify the operating parameter value of X motor up or down (adjustable range

000-255), and press OK to save it. The default value is 000.

2. X Rotation

Modify the X rotation parameter value up or down (adjustable range 000-255),

and press OK to save. The default value is 000.

3. X axis fine

adjustment

Modify the operating parameter value of the X fine tuning motor up or down

(adjustable range 000-255), and save the confirmation key. The default value is

128.

4. Y axis

Modify the Y axis parameter value up or down (adjustable range 000-255), and

press OK to save. The default value is 128.

5. Y Rotation

Modify Y rotation parameter value up or down (adjustable range 000-255), and

press OK to save. The default value is 000.

6. Y-axis fine

adjustment

Modify Y fine-tuning parameter value up or down (adjustable range 000-255), and

press OK to save. The default value is 000.

7. XY speed

Modify the XY speed parameter value up or down (adjustable range 000-255),

and press OK to save. The default value is 000.

8. Focusing

Modify the focusing value up or down (adjustable range 000-255), and press the

OK key to save. The default is 000.

9. General

dimming

Modify the total dimming value up or down (adjustable range 000-255), and press

OK to save. The default value is 255.

10. A Dimming

Modify the dimming value up or down (adjustable range 000-255), and press OK

to save. The default value is 255.

11. A Strobe

Modify the stroboscopic value up or down (adjustable range 000-255), and press

OK to save. The default value is 000.

12. A Red

Modify the brightness of the red lamp bead up or down (adjustable range

000-255), and press OK to save. The default value is 255.

13. A Green

Modify the brightness of the green lamp bead up or down (adjustable range

000-255), and press OK to save. The default value is 255.

14. A Blue

Modify the brightness of the blue lamp bead up or down (adjustable range

000-255), and press OK to save. The default value is 255.

15. A White

Modify the brightness of white lamp beads up or down (adjustable range

000-255), and press OK to save. The default value is 255.

16. Mode A

Modify the mode parameter value up or down (adjustable range 000-255), and

press OK to save. The default value is 000.

17. A Speed

Modify the speed parameter value up or down (adjustable range 000-255), and

press OK to save. The default value is 000.

18. A

Background

color

Modify the background color parameter value up or down (adjustable range

000-255), and press OK to save. The default value is 000.

19. A

Background

tone light

Modify the background tone light parameter value up or down (adjustable range

000-255), and press OK to save. The default value is 000.

20. B Dimming

Modify the dimming value up or down (adjustable range 000-255), and press OK

to save. The default value is 255.

21. B

stroboscopic

Modify the stroboscopic value up or down (adjustable range 000-255), and press

OK to save. The default value is 000.

22. Mode B

Modify the mode parameter value up or down (adjustable range 000-255), and

press OK to save. The default value is 000.

23. Speed B

Modify the speed parameter value up or down (adjustable range 000-255), and

press OK to save. The default value is 000.

24. C dimming

Modify the dimming value up or down (adjustable range 000-255), and press OK

to save. The default value is 255.

25. C

stroboscopic

Modify the stroboscopic value up or down (adjustable range 000-255), and press

OK to save. The default value is 000.

26. C red

Modify the brightness of the red lamp bead up or down (adjustable range

000-255), and press OK to save. The default value is 255.

27. C green

Modify the brightness of the green lamp bead up or down (adjustable range

000-255), and press OK to save. The default value is 255.

28. C Blue

Modify the brightness of the blue lamp bead up or down (adjustable range

000-255), and press OK to save. The default value is 255.

29. Mode C

Modify the mode parameter value up or down (adjustable range 000-255), and

press OK to save. The default value is 000.

30. C speed

Modify the speed parameter value up or down (adjustable range 000-255), and

press OK to save. The default value is 000.

31. C

background

color

Modify the background color parameter value up or down (adjustable range

000-255), and press OK to save. The default value is 000.

32. C

background

tone light

Modify the background tone light parameter value up or down (adjustable range

000-255), and press OK to save. The default value is 000.

33、reset

When the parameter value is 150-255, the whole machine is reset. The console

parameter value must be pulled below 10 and then pushed to 150-255 to be

useful. When the parameter value is 000-149, it is useless and cannot be reset.

4.Display

Settings

1. Language

selection

Select Chinese/EN (English) up or down, and click OK to save. The default is

Chinese.

2. Invert

Settings

Select up or down to close/open the inverted display setting, and press OK to

save it. It is closed by default.

3. Screen saver

Select Close/Open the screen saver up or down, and press the Enter key to save

it. It is enabled by default.

4. Software

version

06XA program ID, which cannot be modified.

5.Factory

Settings

Please enter

password for

display!

Change it up or

down to 138,

and then press

the OK key to

enter the

factory setting。

1. X axis

calibration

Modify the parameters up or down (range 000-255), and press OK

to save. The default value is 128.

2. Y-axis

calibration

Modify the parameters up or down (range 000-255), and press OK

to save. The default value is 128.

2. X-axis

non-polar

Modify X stepless parameter up or down (range 000-255), and

press OK to save. The default value is 128.

2. Y-axis

non-polar

Modify Y stepless parameter up or down (range 000-255), and

press OK to save. The default value is 128.

3. Focus

calibration

Modify the parameters up or down (range 000-255), and press OK

to save. The default value is 128.

2. Focus

stroke

Modify the parameters up or down (range 000-255), and press OK

to save. The default value is 128.

5. Red

Modify the red lamp bead current (032-255) upward or downward,

and press OK to save. The default is 252.

6. Green

Modify the green lamp bead current (032-255) upward or

downward, and press OK to save. The default is 252.

7. Blue

Modify the blue lamp bead current (032-255) upward or downward,

and press OK to save. The default is 252.

8. White

Modify the white lamp bead current (032-255) upward or

downward, and press OK to save. The default is 252.

2. White 3W

Modify the white 3W lamp bead current (032-255) upward or

downward, and press OK to save. The default is 252.

9. X-axis

speed

Modify the X speed parameter up or down (range 000-255), and

press OK to save. The default is 116.

2. Y-axis

Modify Y speed parameter up or down (range 000-255), and press

speed

OK to save. The default is 128.

2、Logo

Select 000/001 up or down, and press OK to save. The default is

000.

Temperature

Modify the temperature parameters up or down (range 40-70), and

press OK to save. The default is 060.

Temperature

- Fan

Select the off/on temperature fan control upward or downward, and

press the OK key to save it. It is off by default.

2、LED

LED selection default LEDA

10. Current

Select 000/007 up or down, and press OK to save. The default is

000.

11、Logo

Select 000/001 up or down, and press OK to save. The default is

000.

12.

Temperature

Modify the temperature parameters up or down (range 40-70), and

press OK to save. The default is 065.

13.

Temperature

- Fan

Select the off/on temperature fan control upward or downward, and

the confirmation key is saved. The default is on.

4.DMX Channels

33 CH Mode

Channel

DMX value

function

000-255

X axis

000-255

X-axis non-polar

000-255

X Trim

000-255

Y axis

000-255

Y-axis non-polar

000-255

Y Trim

000-255

XY speed

000-255

focusing

000-255

Total dimming (AB side)

000-255

RGBW dimming (A-side)

000-255

RGBW strobe (A-side)

000-255

Red (Side A)

000-255

Green (Side A)

000-255

Blue (Side A)

000-255

White (Side A)

000-255

RGBW mode (A-side)

000-255

RGBW speed (A-side)

000-255

Background color (side A)

000-255

Background tone light (side A)

000-255

White 1 (Side B)

000-255

White 1 strobe (B side)

000-255

White 1 mode (B side)

000-255

White 1 speed (B side)

000-255

Red 1 green 1 blue 1 dimming (auxiliary light) (side B)

000-255

Red 1 green 1 blue 1 strobe (secondary light) (side B)

000-255

Red 1 (auxiliary light) (side B)

000-255

Green 1 (secondary light) (side B)

000-255

Blue 1 (secondary light) (side B)

000-255

Red 1 green 1 blue 1 mode (secondary light) (side B)

000-255

Red 1 green 1 blue 1 speed (secondary light) (side B)

000-255

Background color (secondary light) (side B)

000-255

Background tone light (auxiliary light) (side B)

000-255

Reset：When the parameter value is 150-255, the whole machine will be

reset. The console parameter value must be pulled below 10 and then

pushed to 150-255 to be useful. When the parameter value is 000-149, it is

useless and cannot be reset.

53 CH Mode

Channel

DMX value

function

000-255

X axis

000-255

X-axis non-polar

000-255

X Trim

000-255

Y axis

000-255

Y-axis non-polar

000-255

Y-axis fine adjustment

000-255

XY speed

000-255

focusing

000-255

Total dimming (AB side)

000-255

RGBW dimming (A-side)

000-255

RGBW strobe (A-side)

000-255

Red (Side A)

000-255

Green (Side A)

000-255

Blue (Side A)

000-255

White (Side A)

000-255

RGBW mode (A-side)

000-255

RGBW speed (A-side)

000-255

RGB background color (A side)

000-255

RGB background tone light (A-side)

000-255

White dimming (side B)

000-255

White strobe (side B)

000-255

White mode (side B)

000-255

White speed (side B)

000-255

RGB dimming

000-255

RGB strobe

000-255

red

000-255

green

000-255

blue

000-255

RGB mode

000-255

RGB speed

000-255

RGB background color

000-255

RGB background tone light

000-255

Reset：When the parameter value is 150-255, the whole machine will be

reset. The console parameter value must be pulled below 10 and then

pushed to 150-255 to be useful. When the parameter value is 000-149, it is

useless and cannot be reset.

000-255

Red 1 (Side A)

000-255

Green 1 (Side A)

000-255

Blue 1 (Side A)

000-255

White 1 (Side A)

…

… …

000-255

Red 5 (Side A)

000-255

Green 5 (Side A)

000-255

Blue 5 (Side A)

000-255

White 5 (Side A)

69 CH Mode

Channel

DMX value

function

000-255

X axis

000-255

X-axis non-polar

000-255

X Trim

000-255

Y axis

000-255

Y-axis non-polar

000-255

Y-axis fine adjustment

000-255

XY speed

000-255

focusing

000-255

Total dimming (AB side)

000-255

RGBW dimming (A-side)

000-255

RGBW strobe (A-side)

000-255

Red (Side A)

000-255

Green (Side A)

000-255

Blue (Side A)

000-255

White (Side A)

000-255

RGBW mode (A-side)

000-255

RGBW speed (A-side)

000-255

RGB background color (A side)

000-255

RGB background tone light (A-side)

000-255

White dimming (side B)

000-255

White strobe (side B)

000-255

White mode (side B)

000-255

White speed (side B)

000-255

RGB dimming

000-255

RGB strobe

000-255

red

000-255

green

000-255

blue

000-255

RGB mode

000-255

RGB speed

000-255

RGB background color

000-255

RGB background tone light

000-255

Reset：When the parameter value is 150-255, the whole machine will be

reset. The console parameter value must be pulled below 10 and then

pushed to 150-255 to be useful. When the parameter value is 000-149, it is

useless and cannot be reset.

000-255

Red 1 (Side A)

000-255

Green 1 (Side A)

000-255

Blue 1 (Side A)

000-255

White 1 (Side A)

…

… …

000-255

Red 5 (Side A)

000-255

Green 5 (Side A)

000-255

Blue 5 (Side A)

000-255

White 5 (Side A)

000-255

1 White (Side B)

…

… …

000-255

16 White (Side B)

105 CH Mode

Channel

DMX value

function

000-255

X axis

000-255

X-axis non-polar

000-255

X Trim

000-255

Y axis

000-255

Y-axis non-polar

000-255

Y-axis fine adjustment

000-255

XY speed

000-255

focusing

000-255

Total dimming (AB side)

000-255

RGBW dimming (A-side)

000-255

RGBW strobe (A-side)

000-255

Red (Side A)

000-255

Green (Side A)

000-255

Blue (Side A)

000-255

White (Side A)

000-255

RGBW mode (A-side)

000-255

RGBW speed (A-side)

000-255

RGB background color (A side)

000-255

RGB background tone light (A-side)

000-255

White dimming (side B)

000-255

White strobe (side B)

000-255

White mode (side B)

000-255

White speed (side B)

000-255

RGB dimming

000-255

RGB strobe

000-255

red

000-255

green

000-255

blue

000-255

RGB mode

000-255

RGB speed

000-255

RGB background color

000-255

RGB background tone light

000-255

Reset：When the parameter value is 150-255, the whole machine will be

reset. The console parameter value must be pulled below 10 and then

pushed to 150-255 to be useful. When the parameter value is 000-149, it

is useless and cannot be reset.

000-255

Red 1 (Side A)

000-255

Green 1 (Side A)

000-255

Blue 1 (Side A)

000-255

White 1 (Side A)

…

… …

000-255

Red 5 (Side A)

000-255

Green 5 (Side A)

000-255

Blue 5 (Side A)

000-255

White 5 (Side A)

000-255

1 White (Side B)

…

… …

000-255

16 White (Side B)

000-255

Red 1 (Side B)

000-255

Green 1 (Side B)

000-255

Blue 1 (Side B)

…

… …

103

000-255

Red 12 (Side B)

104

000-255

Green 12 (Side B)

105

000-255

Blue 12 (Side B)

Inhaltsverzeichnis

Andere Uplus Lighting Beleuchtungsausrüstung Handbücher

Uplus Lighting

Uplus Lighting 4020 IP Bedienungsanleitung

Uplus Lighting

Uplus Lighting 100SPOT Bedienungsanleitung

Uplus Lighting

Uplus Lighting 360 BEAM Bedienungsanleitung

Uplus Lighting

Uplus Lighting 10X30 COB BAR Bedienungsanleitung

Uplus Lighting

Uplus Lighting RETRO 360 Bedienungsanleitung

Uplus Lighting

Uplus Lighting IR 1210 PAR Bedienungsanleitung

Uplus Lighting

Uplus Lighting W3725 Bedienungsanleitung

Uplus Lighting

Uplus Lighting LED PROFILE MZ Bedienungsanleitung

Uplus Lighting

Uplus Lighting 37X15ZWASH Bedienungsanleitung

Uplus Lighting

Uplus Lighting COB400 ZOOM Bedienungsanleitung

Uplus Lighting

Uplus Lighting BL6 Bedienungsanleitung

Uplus Lighting

Uplus Lighting 280 LED BSW Bedienungsanleitung

Uplus Lighting

Uplus Lighting IP1000 Strobe Bedienungsanleitung

Uplus Lighting

Uplus Lighting W1925 Bedienungsanleitung

Uplus Lighting

Uplus Lighting 150COBPAR Bedienungsanleitung

Uplus Lighting

Uplus Lighting 200 LED RETRO Bedienungsanleitung

Uplus Lighting

Uplus Lighting IP-Z740 Bedienungsanleitung

Uplus Lighting

Uplus Lighting 400 IP BLINDER Bedienungsanleitung

Uplus Lighting

Uplus Lighting LED PROFILE FIX Bedienungsanleitung

Uplus Lighting

Uplus Lighting 6 EYE RETRO BAR Bedienungsanleitung

Uplus Lighting

Uplus Lighting 460LED BSW Bedienungsanleitung

Uplus Lighting

Uplus Lighting BAR 6 LASER Bedienungsanleitung

Uplus Lighting

Uplus Lighting 200 LED BSW Bedienungsanleitung

Uplus Lighting

Uplus Lighting DUAD540 STROBE Bedienungsanleitung

Beliebte Beleuchtungsausrüstung Handbücher anderer Marken

Brizo

Brizo 8SP-MU-4 Bedienungsanleitung

LUCE&LIGHT

LUCE&LIGHT BROM 1.0 Bedienungsanleitung

IKEA

IKEA BJÖRKSPIREA Bedienungsanleitung

Laserworld

Laserworld Evolution Series ES-400RGB Bedienungsanleitung

Alien

Alien RG STAR Bedienungsanleitung

EuroLite

EuroLite LED B-40 Bedienungsanleitung

Qazqa

Qazqa Suplux SL 3 Black 103062 Bedienungsanleitung

Commercial Electric

Commercial Electric 54568141 Bedienungsanleitung

CREE LIGHTING

CREE LIGHTING 304 Series Bedienungsanleitung

Goobay

Goobay 49867 Bedienungsanleitung

ECOMAN ITALIA

ECOMAN ITALIA LED T8 Bedienungsanleitung

Alkalite

Alkalite Krypton KT-81 Bedienungsanleitung

Clas Ohlson

Clas Ohlson GU10 Bedienungsanleitung

DTS

DTS DELTA 10 F Bedienungsanleitung

ring

ring Solar Steplight Bedienungsanleitung

One Stop Gardens

One Stop Gardens 57696 Montageanleitung

Chauvet DJ

Chauvet DJ COREpar UV120 ILS Bedienungsanleitung

SIREM

SIREM Swimeo A2 Bedienungsanleitung