Vacmaster VWM1518R Bedienungsanleitung

VWM1518R

1500W18L

IPX4

www.cleva-europe.com

MADE IN P.R.C

13 14 15 16 17

18 20 21 22

24 25 26 27

TABLE OF CONTENTS

SECTION PAGE

Symbols......................................................................................................................................... 4

Safety Information ......................................................................................................................... 5

Unpacking and Checking Carton Contents ................................................................................... 7

Assembly ...................................................................................................................................... 8

Operation....................................................................................................................................... 9

Maintenance................................................................................................................................ 12

Troubleshooting........................................................................................................................... 13

Technical Data............................................................................................................................. 14

Recycling and Disposal ............................................................................................................... 14

Thank you for purchasing this Vacmaster® wet and dry vacuum cleaner. Feel condent that with

Vacmaster®you are obtaining a high-quality product that is engineered for optimal performance.

This vacuum cleaner is suitable for use with both liquids and dry materials.

FOR YOUR SAFETY: CAREFULLY READ AND UNDERSTAND ALL INSTRUCTIONS.

Caution.

Read instruction manual. Failure to follow the warnings and instructions may

result in electric shock, re and/or serious injury.

Appliance in which protection against electric shock does not rely on basic

insulation only but in which additional safety precautions are provided, such as

double insulation or reinforced insulation, there being no provision for protective

earthing or reliance upon installation conditions.

SYMBOLS

SAFETY INFORMATION

READ AND UNDERSTAND ALL INSTRUCTIONS BEFORE

USING THIS VACUUM CLEANER.

When using the equipment, a few safety precautions must be

observed to avoid injuries and damage. Please read the complete

operating manual with due care. Keep this manual in a safe

place so that the information is always available. If you give

the equipment to any other person, give them these operating

instructions as well. We cannot accept any liability for damage or

accidents which arise due to a failure to follow these instructions

and the safety information.

• Never leave the appliance switched on unattended, if you leave

the work area, switch the appliance off or unplug it from the

power supply.

• Do not vacuum or use this wet and dry Vacuum cleaner near

ammable liquids, gases or explosive vapours like gasoline or

other fuels, lighter uids, cleaners, oil-based paints, natural gas,

hydrogen, or explosive dusts like coal dust, magnesium dust,

grain dust or gun power. Sparks inside the motor can ignite

ammable vapours or dust.

• This vacuum cleaner is not suitable for the vacuuming of

asbestos or asbestos dust.

• Do not vacuum anything that is burning or smoking, such as

cigarettes, matches, or hot ashes.

• Ensure the hose and connections are always pointed away from

the users face, hair, ears and eyes during operation and never

direct the nozzle towards persons or animals.

• Clear the working area of any items or precessions that you do

not wish to be vacuumed before operation.

• Keep cord away from heated surfaces.

• Do not expose to rain. Store indoors.

• Do not unplug by pulling on the cord. To unplug, grasp the plug,

not the cord.

• Do not use with damaged cord, plug or other parts.

• Do not pull or carry by cord, use cord as handle, close a door on

cord, or pull cord around sharp edges or corners.

• Do not handle the plug or vacuum cleaner with wet hands.

• To reduce the risk of health hazards from vapours or dusts, do

not vacuum toxic materials.

• Do not use or store near hazardous materials.

• Do not use this vacuum cleaner with a torn lter or without the

lter installed.

• Do not allow to be used as a toy. Close attention is necessary

when used by or near children.

• To reduce the risk of injury from accidental starting, unplug

power cord before changing or cleaning lter.

• Unplug from power supply when not in use and before carrying

out maintenance.

• Do not cover the ventilation openings. Do not vacuum with any

ventilation openings blocked; keep free of dust, lint, hair or

anything that may reduce air ow.

• Keep hair, loose clothing, ngers, all parts of body away from

openings and moving parts.

• If the supply cord is damaged, it must be replaced by the

manufacturer, a qualied service agent or similarly qualied

persons in order to avoid a hazard.

• This appliance can be used by children aged from 8 years

and above and persons with reduced physical, sensory or

mental capabilities or lack of experience and knowledge if they

have been given supervision or instruction concerning use of

the appliance in a safe way and understanding the hazards

involved.

• Children shall not play with the appliance.

• Cleaning and user maintenance shall not be made by children

without supervision.

• For additional protection: It is recommended that this vacuum

cleaner can be used in conjunction with residual current device

(RCD) with a rated residual current of 30mA or less.

• If foam or liquid escapes from the machine, switch off

immediately.

• Check the oat valve regularly to ensure it is moving freely and

examine it for signs of damage.

When using as blower:

• Direct air discharge only at work area.

• Do not use the wet and dry vacuum cleaner as a sprayer.

• Do not direct air at bystanders.

• Keep children away when blowing.

• Wear safety goggles.

UNPACKING AND CHECKING CARTON

CONTENTS

1 Hose Storage Rod 10 Carry Handle 19 Car Nozzle

2On/Off Switch 11 Extension Wand Storage 20 Cartridge Filter (pre-installed)

3Blower Port 12 Mounting Rack 21 Filter Retainer (pre-installed)

4Suction Port 13 Suction Hose 22 Air Diffuser

5 Container 14 Extension Hose 23 Foam Filter

6 Latch 15 Utility Nozzle 24 Remote Control Handle (with

battery pre-installed)

7Mounting Rack

Release Button 16 Crevice Tool 25 Side Tool Caddy

8 Accessory Storage 17 Round Dusting Brush 26

Screw/Bolt Bag (with 3

screws and 3 expansion

bolts)

9Power Head 18 Extension Wand (×2) 27 Instruction Manual

ASSEMBLY

NOTE: A Phillips screwdriver is required.

1) Remove all the contents from inside of the vacuum cleaner container.

2) Your vacuum cleaner comes ready for dry vacuum cleaning with the cartridge lter pre-installed.

If the cartridge lter is not installed, refer to page 10.

3) For wet vacuuming, replace the cartridge lter with the foam lter supplied. If the foam lter is

not installed, refer to page 10.

4) Place the power head back on the container, and secure into place using the 2 side latches.

5) Insert the air diffuser onto the blower port (Fig. 1).

MOUNTING RACK AND STORAGE ASSEMBLY

IMPORTANT!

• Mount at a recommend height of not more than 1.5m from the oor.

• Ensure you use suitable xings depending on the wall structure.

• Do not hang from or sit on the mounting rack.

• Do not exceed 18kg maximum weight limit.

6) Insert the hose storage rod into the two holes located on the top of the mounting rack. When

secured a click can be heard. Make sure the bend of the rod is directed away from the wall

(Fig. 2).

7) Place the mounting rack against the wall. Make sure the rack is level and mark the hole

locations.

Afx to a Stud Wall:

8) Make a pilot hole in each marked location and secure the mounting rack to the wall with the

three screws provided (Fig. 3).

Afx to a Solid Brick/Concrete Wall:

NOTE: Expansion bolt includes screw, washer, expansion tube and nut.

9) Insert the screws into the supporting holes within the rack. On the revere side, x the washer

and then slide over the expansion tube (Fig. 4).

10) Attached the nut to the end of the screw. The projections on the nut should align with the slots

located at the end of the expansion tube. Loosely pre-tighten the screw and nut.

NOTE: Make sure the expansion tube is not expanded (Fig. 5 & 6).

11) Drill 3 holes into the wall and insert the expansion bolts with rack attached into the holes

accordingly. Secure the mounting rack to the wall by tightening the bolts (Fig. 7).

MOUNTING THE VACUUM ON TO THE RACK

12) Ensure a safe length of power cord is available to plug into the power outlet. Wind the excess

power cord around the cord wrap area located on the rear of the vacuum. Make sure the power

cord is not wound to the hanging hook (A) (Fig. 8).

13) Mount the vacuum onto the mounting rack by aligning the vacuum hanging hook (A) with slot

(B) on the mounting rack and slide downward until it locks. Make sure the cord is not caught

between the hanging hook (A) and the hanging slot (B) (Fig. 9).

14) Attach the tool caddy on either side of the vacuum onto the hooks provided (Fig. 10).

15) Insert the locking end of the hose into the suction port of the container and lock into place

(Fig. 11).

16) Choose the desired accessories and/or extension wands and push t onto the suction hose

nozzle or the remote control handle.

DETACHING THE VACUUM FROM THE RACK

1) Disconnect the power cord from the electrical outlet.

2) Press the release lever located on the left side of the rack (Fig. 12).

3) Lift the vacuum up and out of the rack by the hand.

1. Switching On/Off

Connect the mains plug to a suitable a power outlet.

Position Status

I On

O Off

Remote Control

2. Resetting the Remote Control

The remote control is ready to use. If necessary, follow below instructions to reset it.

1) Have the remote control accessible. Set the power switch on the vacuum to the remote control

position “ ” .

2) Press the RESET button on the side of the power head. The indicator light illuminates RED

(Fig. 13).

NOTE: If the indicator light is ashing, do not proceed to the next step.

3) Release the RESET button once the red indicator light lights up and immediately press and

hold the “I” button on the remote control for 1-3 seconds until the vacuum powers on.

4) If the “I” button is not pressed and held within a 15 second window, the reset will not be

successful. Repeat steps 2-3 to reset the remote control.

5) When the light blinks 3 times, this means the remote control is programmed.

OPERATION

3. Dry & Wet Vacuum Operation

WARNING! ENSURE YOU READ, UNDERSTAND AND APPLY SECTION ENTITLED

‘SAFETY INFORMATION’.

1) Verify that the correct lter is installed for wet or dry vacuuming and the container latches are

secured.

2) The vacuum cleaner can be used either while mounted onto the rack or removed.

3) Secure the locking end of the suction hose onto the vacuum suction port.

4) Push the desired accessories onto the hose nozzle.

5) Plug the power cord into a power outlet.

6) Turn the motor on by assigning the switch to the “I” ON position.

7) If using the remote control handle, set the on/off switch to the remote control position “ ” and

turn the vacuum on by pressing the ‘I’ ON button on the remote control handle for at least one

second (Fig. 14).

8) Once you have completed vacuuming, switch to the “O” OFF position or press the ‘O’ OFF

button on the remote control for at least one second and unplug the power cord from the power.

For Dry Vacuuming:

WARNING: BEFORE INSTALLING, REMOVING OR CLEANING THE VACUUM

CLEANER FILTER, ENSURE THAT THE POWER CORD IS SWITCHED OFF AND

UNPLUGGED.

1) To prepare your vacuum cleaner for dry vacuuming, install the cartridge lter over the lter cage

( ) with the at end of the lter towards the vacuum power head. Carefully push lter until it

sits ush forming a tight seal (Fig. 15).

2) Place the lter retainer on top of the cartridge lter over the raised lip and tighten the retainer

lock clockwise to secure against the internal lter cage (Fig. 16).

IMPORTANT: Check the lter regularly for optimal performance. An old or blocked lter will reduce

suction performance.

For Wet Vacuuming:

IMPORTANT: When vacuuming large volumes of liquids, we recommend that you remove the

vacuum from the wall mounting rack and place on the oor. The vacuum can be heavy when full of

liquids and may be difcult to remove from the rack.

1) To prepare your vacuum cleaner for wet vacuuming, remove the retainer cover and the dry use

cartridge lter.

2) Carefully install the supplied foam lter over the internal lter cage, making sure the whole cage

is covered (Fig. 17).

WARNING:

DO NOT USE THE CARTRIDGE FILTER FOR WET VACUUMING.

DO NOT SUBMERGER THE REMOTE CONTROL INTO LIQUIDS.

Inhaltsverzeichnis

Sprachen:

Andere Vacmaster Staubsauger Handbücher

Vacmaster

Vacmaster VJH1211PF 1101 Bedienungsanleitung

Vacmaster

Vacmaster VSG2101 Bedienungsanleitung

Vacmaster

Vacmaster VJC1210PF Bedienungsanleitung

Vacmaster

Vacmaster VMVK1530SIWDC Bedienungsanleitung

Vacmaster

Vacmaster VJH2012PF 1101 Bedienungsanleitung

Vacmaster

Vacmaster VJF912PF 0201 Bedienungsanleitung

Vacmaster

Vacmaster VFB511B 0201 Bedienungsanleitung

Vacmaster

Vacmaster VJH1211PF 0201 Bedienungsanleitung

Vacmaster

Vacmaster VQ1220PFC Bedienungsanleitung

Vacmaster

Vacmaster VK1638SWC Bedienungsanleitung

Vacmaster

Vacmaster VF408 Bedienungsanleitung

Vacmaster

Vacmaster VK811PH Bedienungsanleitung

Vacmaster

Vacmaster VJF910PF 0201 Bedienungsanleitung

Vacmaster

Vacmaster VJF910PF Bedienungsanleitung

Vacmaster

Vacmaster UC0902EHUK Bedienungsanleitung

Vacmaster

Vacmaster EasyClean SCA0801 Bedienungsanleitung

Vacmaster

Vacmaster VZA0708P Bedienungsanleitung

Vacmaster

Vacmaster VJF607PF 1101 Bedienungsanleitung

Vacmaster

Vacmaster VJC809PF Bedienungsanleitung

Vacmaster

Vacmaster UC0101 Bedienungsanleitung

Vacmaster

Vacmaster VK1530SIWDC-T 950204 Bedienungsanleitung

Vacmaster

Vacmaster VHB307WM Bedienungsanleitung

Vacmaster

Vacmaster UB0212EUK Bedienungsanleitung

Vacmaster

Vacmaster VJE1412SW 0202 Bedienungsanleitung

Beliebte Staubsauger Handbücher anderer Marken

Bissell

Bissell LittleGreen Proheat 1425 Series Bedienungsanleitung

Panasonic

Panasonic MC-YL637S147-AE Bedienungsanleitung

NEFF

NEFF N17XH10 0 Series Bedienungsanleitung

LG A9 Series Bedienungsanleitung

Oreck

Oreck Cordless Captura BK51700 Series Bedienungsanleitung

Kogan

Kogan KAVACROBVWA Bedienungsanleitung

Kränzle

Kränzle VENTOS 50 ID Benutzerhandbuch

EVVO

EVVO Ai35 Bedienungsanleitung

DeWalt

DeWalt DWH200D Bedienungsanleitung

Pontec

Pontec Pondomatic Vacuum Cleaner Bedienungsanleitung

Cleanmaxx

Cleanmaxx PC-P007E Bedienungsanleitung

Exido

Exido 240-114 Bedienungsanleitung

RIDGID

RIDGID WD1685AU0 Bedienungsanleitung

Ezviz

Ezviz RE4P Bedienungsanleitung

STG global

STG global TANVAC HDV3000 Bedienungsanleitung

Shark

Shark ROTATOR PRO COMPLETE NV550 Series Bedienungsanleitung

Factory

Factory M3340 Bedienungsanleitung

Shop-Vac

Shop-Vac VN92 SERIES Bedienungsanleitung