Vax W87-DV-B Montageanleitung

vax.co.uk

W87-DV-(B, R, T)

Dual V Advance

Let’s get started

This carpet washer is intended for

household use only and NOT for

commercial or industrial use.

• Only use the carpet washer indoors

and keep the area you’re cleaning

well lit.

• Keep ngers, hair and loose clothing

away from moving parts and

openings whilst using the

carpet washer.

• This appliance can be used by

children aged from 8 years and

above and persons with reduced

physical, sensory or mental

capabilities or lack of experience

and knowledge if they have been

given supervision or instruction

concerning use of the appliance

in a safe way and understand the

hazards involved. Children shall not

play with the appliance. Cleaning

and user maintenance shall not

be made by children without

supervision.

• Before using the carpet washer test

your carpets/rugs/upholstery for

colourfastness and pile distortion.

• Only Vax recommended tools

and detergent should be used

with this carpet washer. Using

other detergents may invalidate

the guarantee.

Basic safety precautions

Do’s

8 Check with the manufacturer

of your ooring prior to using

the carpet washer to ensure

its suitability.

8The clean water tank should be

lled with warm water (max

40C) only. Filling the clean water

tank with hot or boiling water will

damage the machine and invalidate

the guarantee.

8Always vacuum your carpets

thoroughly before using the

carpet washer.

Let’s talk safety

Don’ts

8 Always unplug the carpet

washer before carrying out

any maintenance and before

connecting or disconnecting the

hose/accessories.

8Turn o all controls on the carpet

washer before disconnecting or

connecting the power cord, after

use always wrap the power cord

around the cord clips provided.

8 Always replace the fuse in the plug

with a British 13amp fuse.

8Always protect the power cable

from heated surfaces or near

open ames.

8 Always protect the power cable

from heated surfaces or near

open ames.

8 Always keep the power cord away

from the brushes whilst using the

carpet washer.

3Take extra care when cleaning on

the stairs.

3Always use the carpet washer with

all water/detergent tank and lters

in place.

3Keep all openings clear and free

from debris as this may aect the

airow/suction.

3Always use the carpet washer

in an upright position. To prevent

motor damage from dirty water,

never hold the carpet washer

upside down or on its side.

3Store the carpet washer in a cool,

dry area. Before storing the carpet

washer please ensure all water/

detergent tanks and lters are

thoroughly clean and dry.

Please keep instructions

for further use.

Don’ts

Thank you for buying this Dual V Advance.

Taking care of your carpets

The Dual V Advance is designed to make washing carpets regularly, as eective and ecient as

possible and this user guide will help you get the most out of your machine.

Maintaining your carpets will ensure they keep their appearance for longer and smell fresh and

clean. You’ve chosen carpets for your home for a reason and Vax will help you take good care

of them.

Taking care of your Dual V Advance

Also inside this guide are instructions on maintaining your new machine, so that it’s always ready

when you are to tackle your carpets.

Taking care of you

We’re here if you need us. Instead of taking me back

to the shop, simply visit:

vax.co.uk/support or call:

(UK) 0844 412 8455 (ROI) 1-800 928 308

Monday-Friday 8.30am to 6.30pm, Saturday 9.00am to 5.00pm

Calls are charged at the UK local rate. Please make a note of the serial number and model number

of the product before calling.

Alternatively, you can write to us at:

Vax Ltd., Kingswood Road, Hampton Lovett, Droitwich, Worcestershire, WR9 0QH, UK

Let us know what you think @VaxUK

Contents

Let’s talk safety

Getting to know your machine

Getting started

Using your machine

Taking care of your machine

What to do if it goes wrong

Getting in touch

Accessories

Dual V Advance

Vax Ultra+ Carpet

Cleaning solution

Included with

your machine

Wash tool

SpinScrub wash tool

2.6m hose

Hard oor tool

Floor to oor solution

Dual V Advance

Total Home

4.2m hose

Dual V Advance

Reach

Recline pedal

Max Extract pedal

Stretch hose

caddy

Power cable hook

Power cable

Wheels

Hose/Stretch hose

Name Dual V Advance

Code: W87-DV-B

Voltage: 220-240V~50Hz

Wattage: 1350W

Clean water tank capacity: 3.7L

Dirty water tank: 3.2L

Cord length 10m

Weight 10.3kg (depending on model)

Hose length W87-DV-B – 2.6m

W87-DV-R – 4.2m

W87-DV-T – 4.2m

Technical Specication

Subject to technical change without notice. *To purchase consumables and accessories, please visit vax.co.uk

Getting to know your machine

Handle grip

Trigger (hidden)

SpinScrub caddy

SpinScrub wash tool

On/O switch

Mode selector switch

Clean water tank

Dirty water tank

carry handle

Carry handle

Dirty water tank

Hose connection port

Nozzle

Edge Cleaners

Detergent tube

connector port

SpinScrub brushes

(hidden)

Clean water tank

release button

Getting started

Do not saturate your carpet.

• Test for colourfastness – Wet a white absorbent cloth with the detergent. In a small hidden area of your carpet/rugs

/upholstery gently rub with the dampened cloth. Wait ten minutes and check for colour removal or bleed with white

paper towel or cloth. If your carpet has more than one colour, check all colours.

• Test your carpet/rugs/upholstery – Run the carpet washer over a small hidden area. If no pile distortion occurs

continue cleaning.

• When cleaning an entire room, move furniture out of the area to be cleaned. If the furniture cannot be moved, place

aluminium foil or wax paper under the legs. This will prevent wood nishes from staining your carpet. Pin up furniture

skirts and curtains.

• When using the carpet washer, basic safety precautions should always be observed and don’t over saturate

your carpets.

• Only use Vax carpet detergent. Using other detergents may cause excess foaming and will invalidate your guarantee.

• The clean water tank should only be lled with warm water (max 40C). Filling the clean water tank with hot/boiling

water will damage your machine and invalidate the guarantee. This is a powerful carpet washer, before plugging in

make sure all controls are turned o and hold carpet washer rmly when starting and during use.

IMPORTANT: Carpets should be dry vacuumed thoroughly before washing.

TIP

Automix tank so any detergent

not used can be poured back

into the bottle.

Assembling your upright

Push handle into

main body.

Press clean water tank

release button.

Line up tabs on water tank

cap with clean water tank,

twist clockwise to re-t.

Pour required carpet/hard

oor detergent into tank.

Twist locking tab

clockwise to lock

into place.

Stretch hose (Some models

only) - Clip hose connector into

top hose caddy wrap hose down

and around bottom caddy, up and

around top caddy clipping other

end of hose into bottom caddy.

Turn handle lock dial

clockwise to lock in place.

Pull to remove clean

water tank.

Twist detergent cap anti

-clockwise to remove.

Line up tabs on detergent

cap with clean water tank,

twist clockwise to re-t.

Hold locking tab

vertically, line up bottom

caddy (smallest of the

two) with black panel

on carport washer.

40C

Max

Line up SpinScrub hand

tool into SpinScrub caddy,

push until clicks into place.

Twist clean water tank cap

anti clockwise to remove.

Fill clean water tank

to ‘max’ ll mark.

Twist locking tab

clockwise to lock

into place.

Hold locking tab

vertically, line up top

caddy (largest of the

two) with back panel

on carpet washer.

Clip hose connector into top

hose caddy and wrap hose

down and around bottom

caddy. Clip the other end of

the hose into the opposite

side of top caddy.

Filling the water/detergent tank

Getting started Using your machine

WARNING: Always unplug the carpet washer before performing any maintenance/troubleshooting checks.

IMPORTANT: Your dirty water tank is tted with a oat. When the dirty water tank is full, or the nozzle is not in

contact with the carpet the oat will shut o the suction on the carpet washer. You will be able

to hear if this has happened as the motor noise on the machine will increase. Once the oat is

activated, empty the dirty water tank if full. If the dirty water tank is not full then turn o your

machine at the power switch and wait for the oat to settle.

Select Rinse on the mode

selector switch.

Rinsing your carpets/hard oor

Rinsing is not necessary, but will help remove detergent residue leaving your carpets/hard oor looking fresher.

Max Extract

For superior drying performance use the Max Extract pedal with Max Extract on the mode selector switch.

The SpinScrub brushes will not spin when the Max Extract pedal is pressed, the entire power of the carpet washer

is used to extract water/detergent from your carpets.

Washing your carpets

Using your machine Using your machine

Plug into mains, press the on

/o button to switch on.

Squeeze trigger to release

detergent and water mix.

Squeeze trigger to release

water.

Squeeze trigger on forward

stroke, release trigger on

backward stroke to recover water.

Press the recline pedal and pull

handle backwards.

Squeeze trigger on the

forward stroke, release trigger

on backward stroke to recover

detergent/water.

Select Wash on the mode

selector switch.

NOTE: Carpets should be dry vacuumed thoroughly before washing.

Mode selector functions

WASH: SpinScrub brushes deep clean your carpets with water and detergent removing dirt and stains.

RINSE: Only water is released to remove detergent residue.

MAX EXTRACT: Extracts any water/detergent from your carpets/hard oors (some models only). No water/detergent

mix will be released during this function (even when trigger is pressed). Use this mode in combination with the Max

Extract pedal for superior drying performance. Ideal for large spills.

TIP

Avoid saturating your carpet, do

not use more than 4 wet strokes

over one area. Always end with

dry strokes. For heavily soiled

areas, it may be necessary to

repeat the cleaning process.

Make crisscrossing strokes to

the original pattern and overlap

each pass.

Select Max Extract on the

mode selector switch.

Press the Max Extract

pedal to activate the Max

Extract mode.

The brushes will not spin

when the Max Extract

pedal is pressed but

may turn slowly as the

carpet washer is moved

forwards/backwards.

Press the Max Extract

pedal to de-activate the

Max Extract mode.

TIP

For best results use slow

straight parallel strokes.

Using your machine Using your machine

Washing hard oors (some models only)

CAUTION: To prevent damage to wood oors and other hard oors, follow the ooring manufacturer’s cleaning

recommendations. Inspect oor surface for worn nish, bare wood or separated joints. It’s not recommended to use the

carpet washer on oors if any of these conditions exist.

IMPORTANT: Before attaching the hard oor squeegee onto carpet washer remove tanks, or make sure tanks are empty

before lying the carpet washer on its back.

Using the SpinScrub and Upholstery wash tool

IMPORTANT: Check the cleaning code on your upholstery. Use the cleaner only on upholstery marked ‘W’ or ‘W/S’.

Check with the manufacturer before use. Run the SpinScrub brush and upholstery wash tools over a small hidden area to

test before cleaning. When using the hose, select Wash on the mode selector switch.

No water/detergent will be delivered on Rinse or Max Extract mode.

Choosing an accessory

TIP

Rinsing is not necessary,

but will help remove

detergent and residue

leaving your hard oors

looking fresher. Go to

‘Rinsing your carpets/

hard oor’.

Lie carpet washer on its

back, line up squeegee

with nozzle.

Unclip and remove hose.

Stand carpet washer

upright. Fill clean water tank

with water and detergent

tank with hard oor

detergent. Go to ‘Filling the

water/detergent tank’.

Line up detergent tube

connector with detergent

tube connection port. Push

and twist clockwise to lock

into place.

Select Wash on the mode

selector switch.

Click

Hook front of squeegee

onto edge of nozzle.

Lift cover on hose

connection port.

Plug into mains, press the

on/o button to switch on.

Squeeze trigger to release

detergent and water mix.

Squeeze trigger on

forward stroke, release

trigger on backward stroke

to extract detergent/water.

Push squeegee under nozzle

until it clicks into place.

Line up tabs on hose into

hose connection port.

Push and twist hose

clockwise to lock into place.

Press the recline pedal and

pull handle backwards.

Choose an accessory.

Press the on/o button to switch

on. Select Wash on mode

selector switch (No water/

detergent will be delivered on

Rinse or Max Extract mode).

Press trigger on hose to release

detergent/water.

Slide accessory tool over tab at end

of hose until it clicks into place.

Squeeze trigger on the

forward stroke, release trigger

on backward stroke to recover

detergent/water.

Taking care of your machine Taking care of your machine

WARNING: Always switch o and unplug the carpet washer from the mains before assembling, lling and emptying

the clean water tank, emptying the dirty water tank or before connecting/disconnecting the attachments.

WARNING: Always unplug the carpet washer before performing any maintenance/troubleshooting checks

All water and detergent must be removed from tanks.

IMPORTANT: If the hose or tools are blocked, switch o the carpet washer and remove the blockage(s) before

re-starting your machine.

Emptying the dirty water tank

Cleaning the base lint lter

Lift dirt water tank by

carry handle.

Empty dirty water over

the sink. Rinse dirty water

tank and lid under water to

remove debris.

Pull to remove dirty

water tank.

Clean the lter screen

located at the back of the

dirty water tank by scooping

out the debris.

Lift dirty water tank clip up

and outward to release.

Empty and rinse out clean and

dirty water tanks and leave to

air dry before replacing.

Do not leave detergent/

water stored in the tanks

between uses

IMPORTANT

Cleaning the nozzle

Lie carpet washer on its

back. The lter is located

behind the brushes.

Leave to dry for 24 hours

or until fully dry before

placing back in the carpet

washer.

Pull lter to remove. Rinse lter under water to

remove debris.

Remove dirty water tank.

Lift and pull top of nozzle

to remove.

Rinse nozzle under water

to remove debris.

Line up tabs on nozzle with

holes in carpet washer. Slide

tabs into holes, press down on

nozzle until clicks into place.

TIP

The lint lter should be

checked and cleaned after

every use, if blocked the

SpinScrub brushes may

not turn.

Taking care of your machine

Removing blockages from the SpinScrub brushes

Advance SpinScrub brush maintenance

Lie carpet washer

on its back.

Pull rmly to unclip each

side of SpinScrub cover

(one side at a time).

Leave to fully dry. Line up

tabs on side of SpinScrub

cover into carpet washer,

push rmly until clicks

into place.

Leave to fully dry. Line

up tabs on side of

SpinScrub cover with

carpet washer, push rmly

until clicks into place.

Firmly pull sides

of SpinScrub

cover to remove.

Remove individual

brushes, clean and rinse

under running water to

remove debris.

Remove any threads or

hair caught around the

brush, rinse under water to

remove debris.

Ret the individual

brushes. Line up tabs on

SpinScrub cover with

tabs on brush frame.

Push and clip covers until

click into place.

What to do if it goes wrong

• Check the ‘This pack contains’ panel on the box to make sure the part

is denitely included in your unit.

• It may not be plugged into the mains correctly: ensure that the plug is pushed

in securely and switched on.

• The power button hasn’t been fully depressed.

• If the carpet washer cuts out during use, disconnect from the mains, allow

to cool for one hour, empty the dirty water tank, clean the lter and check

hose and SpinScrub brushes for blockages.

• Make sure the clean water tank is tted correctly.

• The detergent/clean water tank may be empty.

• Check the carpet washer is on the correct setting no water will be

dispensed when using the Max Extract mode.

• No water will be dispensed on Rinse or Max Extract mode when

using the hose.

• The brushes will only rotate when the carpet washer is reclined

and turned on.

• The brushes will not rotate when set in the Max Extract mode.

• Check the lint lter and clean if necessary.

• The oat in the dirty water tank may have been activated. Empty the dirty

water tank if full. If the dirty water tank is not full then switch the carpet

washer o and wait for the oat to settle before re-starting your machine.

• The dirty water tank may be full and the auto shut o engaged. Empty

the dirty water tank.

• Make sure the dirty water tank is tted correctly and the tank cap

is securely tted.

• Check the hose for blockages.

• Check the SpinScrub brushes for blockages.

• Check the nozzle is tted correctly and for any blockages.

SolutionProblem

Is there an accessory

missing?

Why won’t the carpet

washer turn on?

Why won’t the cleaner

pick up detergent/

water/spills?

Why won’t the

detergent/clean

water dispense?

Why won’t the

brushes rotate?

Getting in touch

* Calls are charged at the UK local rate. Please make a note of the serial number and model number of the product before calling.

Accessories

Don’t forget your solution!

Order at: www.vax.co.uk/spares-and-solutions

Ultra+ Pet carpet cleaning solution (1.5l)

1-9-132707-00

Ultra+ Pet Carpet Cleaning Solution tackles stubborn spots

and stains and removes unpleasant pet odours too. It’s

specially formulated to leave no sticky residue, so your

carpets stay fresher for longer.

Ultra+ Allergen (1.5l)

1-9-133262-00

Ultra+ Allergen tackles stubborn spots and stains, but also

removes deep down dirt and allergens in your carpet.

Formulates to leave no sticky residue, so your carpets stay

fresher for longer. Ultra+ Allergen carpet cleaning solution

is approved by the British Allergy Foundation.

Ultra+ Sanitise (1.5l)

1-9-133261-00

Ultra+ Sanitise tackles stubborn spots and stains and

removes embedded dust and dirt from carpet pile. Ultra+

Sanitise is formulated to leave no sticky residue, so your

carpets stay fresher for longer.

Ultra+ carpet cleaning solution (1.5l)

1-9-132706-00

Ultra+ Carpet Cleaning Solution tackles stubborn spots and

stains and removes unpleasant odours too. It’s specially

formulated to leave no sticky residue, so your carpets stay

fresher for longer.

Ultra+ Refresh & Revitalise (1.5l)

1-9-133260-00

Ultra+ Refresh and Revitalise tackles stubborn spots and

stains. It’s Oxy-Lift Action Technology brings your carpets

back to life and restores carpet pile. Formulates to leave no

sticky residue, so your carpets stay fresher for longer. Safe

to use on wool carpets - Woolsafe approved.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Vax Staubsauger Handbücher

Vax

Vax Powerplus pet 18 V Bedienungsanleitung

Vax

Vax V-303 Wash "N' Dry Bedienungsanleitung

Vax

Vax VPPST1600 Bedienungsanleitung

Vax

Vax V-048 Bedienungsanleitung

Vax

Vax VX82 Bedienungsanleitung

Vax

Vax V-2000 U Bedienungsanleitung

Vax

Vax VUAMM1600T Bedienungsanleitung

Vax

Vax VaxAIR VCAB1500 Bedienungsanleitung

Vax

Vax Essentials VEW-01 Bedienungsanleitung

Vax

Vax Vivality V-0071 Produktinformationsblatt

Vax

Vax VCU-O3C Bedienungsanleitung

Vax

Vax AWU01 Montageanleitung

Vax

Vax action 802 U86-AB-Be Technisches Datenblatt

Vax

Vax Air3 Agile Bedienungsanleitung

Vax

Vax INFINITY V-116B Bedienungsanleitung

Vax

Vax Silence 420 Bedienungsanleitung

Vax

Vax VS-033 Produktinformationsblatt

Vax

Vax H85-AC21-B Bedienungsanleitung

Vax

Vax Force 10 Cyclonic VZL-401CSP Bedienungsanleitung

Vax

Vax U91-M1 Series Bedienungsanleitung

Vax

Vax ONE PWR CORDLESS BLADE 4 Series Bedienungsanleitung

Vax

Vax V-112P Bedienungsanleitung

Vax

Vax V-028 Bedienungsanleitung

Vax

Vax V-118 Bedienungsanleitung

Beliebte Staubsauger Handbücher anderer Marken

Bissell

Bissell LittleGreen Proheat 1425 Series Bedienungsanleitung

Panasonic

Panasonic MC-YL637S147-AE Bedienungsanleitung

NEFF

NEFF N17XH10 0 Series Bedienungsanleitung

LG A9 Series Bedienungsanleitung

Oreck

Oreck Cordless Captura BK51700 Series Bedienungsanleitung

Kogan

Kogan KAVACROBVWA Bedienungsanleitung

Kränzle

Kränzle VENTOS 50 ID Benutzerhandbuch

EVVO

EVVO Ai35 Bedienungsanleitung

DeWalt

DeWalt DWH200D Bedienungsanleitung

Pontec

Pontec Pondomatic Vacuum Cleaner Bedienungsanleitung

Cleanmaxx

Cleanmaxx PC-P007E Bedienungsanleitung

Exido

Exido 240-114 Bedienungsanleitung

RIDGID

RIDGID WD1685AU0 Bedienungsanleitung

Ezviz

Ezviz RE4P Bedienungsanleitung

STG global

STG global TANVAC HDV3000 Bedienungsanleitung

Shark

Shark ROTATOR PRO COMPLETE NV550 Series Bedienungsanleitung

Factory

Factory M3340 Bedienungsanleitung

Shop-Vac

Shop-Vac VN92 SERIES Bedienungsanleitung