Vicon XX247-32-00 Bedienungsanleitung

ViconNet 8.0 Software

XXYYY-XX-XX

Vicon Industries Inc. does not warrant that the functions contained in this equipment will

meet your requirements or that the operation will be entirely error free or perform

precisely as described in the documentation. This system has not been designed to be

used in life-critical situations and must not be used for this purpose.

Document Number: 8009-8247-32-00 Product specifications subject to change without

Vicon Industries Inc.

Tel: 631-952-2288) Fax: 631-951-2288

Toll Free: 800-645-9116

24-Hour Technical Support: 800-34-VICON

(800-348-4266) UK: 44/(0) 1489-566300

www.vicon-security.com

XX247-32-00

ROUGHNECK V-CELL-HD-B

Corner-Mount Network Camera

Quick Installation Guide

V-CELL-HD-B Quick Installation Guide

1. Description

The information in this manual provides quick installation and setup procedures for the V-CELL-HD-B of High-

Security Corner-Mounted Cameras. These units should only be installed by a qualified technician using

approved materials in conformance with federal, state, and local codes. Read these instructions thoroughly

before beginning an installation. Refer to the complete manual for detailed information. Always refer to Vicon’s

website to assure you have the most up-to-date manual, http://www.vicon-security.com.

The Roughneck® V-CELL-HD-B high-security camera is an integrated housing, camera, lens and IR illuminators

system specifically designed for use in custodial suites and prison cells. It is available in an IP version that is

fully compatible with all Vicon Valerus®and ViconNet®systems; its ONVIF certification provides an open-

platform for integration into other video management systems.

The housing is designed to fit into a corner; once installed, the base plate should be permanently sealed to the

wall so that the housing is ligature proof. The housing consists of a two part stainless steel assembly, a fixed

base plate and a removable front plate, that allows ease of installation and servicing. The front plate is secured

with security screws and has two polycarbonate windows to protect the camera and IR illuminators. The alarm

input and alarm output can be used to connect various third party devices, such as door sensors and alarm

bells.

1.1 Components

The system comes with the following components:

Camera unit Installation Guide Installation CD Accessory Kit

Check your package to make sure that you received the complete system, including all components shown

above.

V-CELL-HD-B Quick Installation Guide

2. Installation

For the network camera to operate, it is necessary to connect a network cable for data transmission and power

connection from customer-supplied power supply.

2.1 Overview

Parts and Description

①Mounting Frame

②Mic

③Camera/Lens

④Speaker

⑤Camera Bracket

⑥IR Window & IR LED

⑦Status LED

①Main Power 12 VDC (↑(-) pole /↓(+) pole)

②RJ45 (PoE) Port

③Micro-SD Card Slot

④Alarm & Audio In/Out Port

⑤Status LED

Upon boot-up, green and red LEDs are both on for a short time and then only green will be on.

If red is lit, this indicates a failure (no picture); if flashing green and no red, this indicates that a

good picture is displaying.

V-CELL-HD-B Quick Installation Guide

Below is an overview for installing the camera.

1) Installation (without Rear Cover)

1. Use camera mounting frame as template to mark mounting holes on mounting surface. (Fig.1)

2. Drill holes for mounting base and a minimum 3/4 in. hole for routing wines. (Fig.1)

3. Mount camera mounting frame using appropriate hardware for mounting surface. (Fig.2)

4. Route wires through hole in wall and out through base plate. (Fig.2).

5. Terminate wires to camera board.

6. Mount front plate to base plate. (Fig.2)

V-CELL-HD-B Quick Installation Guide

2) Installation (using Rear Cover)

1. Use rear cover as template to mark mounting and cable access holes.

2. Drill mounting and cable access holes in mounting surface.

3. Insert cable clamp into access hole, route cables through clamp and mount cover using appropriate

hardware.

4. Use camera mounting frame to mark its mounting holes, drill holes and mount using appropriate

hardware.

5. Terminate wires to camera board. Feed the excess wire back through cable clamp and tighten clamp.

6. Mount front plate to camera mounting frame.

Note: Installation of the rear cover is required for UL/Canadian UL compliance.

V-CELL-HD-B Quick Installation Guide

2.2 Cable Connections

All cabling is done to the boards located on the back of the front plate.

1) Micro SD memory slot on the Board

Card Slot for Micro SD memory: Socket “J10.” (SD card customer-supplied.)

2) Connecting to the RJ-45

Connect a standard RJ-45 cable to the network port of the network camera. Generally a

crossover cable is used for direct connection to a PC, while a direct cable is used for

connection to a hub.

3) Connecting Alarms

AI (Alarm In):

External devices can be used to signal the network camera to react upon events. Mechanical

or electrical switches can be wired to the AI (Alarm In) and G (Ground) connectors.

G (Ground):

Connect the ground side of the alarm input and/or alarm output to the G (Ground) connector.

Alarm Out:

The network camera can activate external devices such as buzzers or lights. Connect the

device to the AO (Alarm Out) and G (Ground) connectors.

4) Connecting the Power

Connect the power of 12 VDC for the network camera. Connect the positive (+) pole to the ‘+’ position and

the negative (-) pole to the ‘-’ position for the DC power.

Be careful not to reverse the polarity when connecting the power cable.

A router featuring PoE (Power over Ethernet) can also be used to supply power to the camera.

The heater can be powered by a 12 VDC, or PoE power source.

For the power specifications, refer to the Appendix, Product Specification.

If PoE and 12 VDC are both applied, the camera will be supplied with power from PoE.

5) IR Control

To adjust the intensity of the IR illuminators, use the Day & Night menu in the web browser.

Final Installation

When all connections are made, secure the front plate to the base plate using the security screws

previously removed using no. 20 Torx bit.

V-CELL-HD-B Quick Installation Guide

2.3 Network Connection and IP assignment

The network camera is designed for use on an Ethernet network and requires an IP address for access. Most

networks today have a DHCP server that automatically assigns IP addresses to connected devices. By the

factory default, your camera is set to obtain the IP address automatically via DHCP server. If your network

does not have a DHCP server the network camera will use 192.168.1.100 as the default IP address.

If DHCP is enabled and the product cannot be accessed, run the “Smart Manager” utility on the CD to search

and allocate an IP address to your products, or reset the product to the factory default settings and then

perform the installation again.

1. Connect the network camera to the network and power up.

2. Start SmartManager utility (Start>All Programs>SmartManager>SmartManager); the main window

displays. After a short while any network devices connected to the network will be displayed in the list.

3. Select the camera on the list and click right button of the mouse. The pop-up menu below displays.

4. Select Assign IP. The Assign IP window displays. Enter the required IP address.

Note: For more information, refer to the Smart

Manger User’s Manual.

V-CELL-HD-B Quick Installation Guide

3. Operation

The network camera can be used with Windows® operating system and browsers. The recommended

browsers are Internet Explorer®, Safari®, Firefox®, Opera® and Google® Chrome® with Windows.

Note: To view streaming video in Microsoft® Internet Explorer, set your browser to allow ActiveX controls.

Note: Some screens may appear different (i.e., color scheme) depending on the firmware version, but the

functionality is the same or similar.

3.1 Access from a Browser

1. Start a browser (i.e., Internet Explorer).

2. Enter the IP address or host name of the network camera in the Location/Address field of the browser.

3. A starting page displays. Click Live View, Playback or Setup to select corresponding web page.

4. Click Live View for the network camera’s Live View page to appear in the browser.

V-CELL-HD-B Quick Installation Guide

3.2. Access from the Internet

Once connected, the network camera is accessible on your local network (LAN). To access the network camera

from the Internet you must configure your broadband router to allow incoming data traffic to the network

camera. To do this, enable the NAT-traversal feature, which will attempt to automatically configure the router

to allow access to the network camera. This is enabled from Setup > System > Network > NAT.

For more information, refer to section “3.5.6 System>Network>NAT” of the User’s manual.

3.3 Setting the Admin Password Over a Secure Connection

To gain access to the camera, the password for

the default administrator user must be set. This is

done in the “Admin Password” dialog, which is

displayed when the network

camera is accessed for

setup the first time.

Enter your admin name and

password, set by the administrator.

Not

The default administrator username is

“ADMIN” and password is “1234”. If the password

is lost, the network camera must be reset to the

factory default settings. See section “3.8 Resetting

to the Factory Default Settings” for more details.

To prevent network eavesdropping when setting the admin password, it can be done via an encrypted HTTPS

connection, which requires an HTTPS certificate (see note below).

To set the password via a standard HTTP connection, enter it directly in the first dialog shown below. To set

the password via an encrypted HTTPS connection, see “3.5.6 System > Security > HTTPS”.

Note: HTTPS (Hypertext Transfer Protocol over SSL) is a protocol used to encrypt the traffic between web

browsers and servers. The HTTPS certificate controls the encrypted exchange of information.

3.4 Live View Page

The Live View page provides several

screen modes

, including: 2048x1536,

1920x1080, 1280x1024, 1280x720,

704x480 (576), 640x480, 352x240

(288), and 320x240. Select the most

suitab

le mode in accordance with your

PC specifications and monitoring

purposes.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Vicon Sicherheitskamera Handbücher

Vicon

Vicon VC-620 Bedienungsanleitung

Vicon

Vicon V3FD Series Bedienungsanleitung

Vicon

Vicon S-10CM Bedienungsanleitung

Vicon

Vicon VC367DSP Bedienungsanleitung

Vicon

Vicon V9360-1 Bedienungsanleitung

Vicon

Vicon V922B-W551MIR-A1 Bedienungsanleitung

Vicon

Vicon Roughneck Pro V2000D Series Bedienungsanleitung

Vicon

Vicon Cruiser SN663V Betriebsanleitung

Vicon

Vicon CE202D-WN Bedienungsanleitung

Vicon

Vicon 240-60 Series Bedienungsanleitung

Vicon

Vicon V900-358-24C Bedienungsanleitung

Vicon

Vicon Surveyor 4 Bedienungsanleitung

Vicon

Vicon Surveyor MKII Series XX282-00-01 Bedienungsanleitung

Vicon

Vicon Roughneck AI V2008B-W310LPR Bedienungsanleitung

Vicon

Vicon I-Onyx VN-957DN Bedienungsanleitung

Vicon

Vicon VC-630 Bedienungsanleitung

Vicon

Vicon SVFT-MSH23C Bedienungsanleitung

Vicon

Vicon S10-CH Mini Bedienungsanleitung

Vicon

Vicon i-onyx MP-980DN Handbuch

Vicon

Vicon Surveyor MKII Series XX282-40-01 Kurzanleitung

Vicon

Vicon V2008-W0950-LPR Bedienungsanleitung

Vicon

Vicon V940D Bedienungsanleitung

Vicon

Vicon VC-600W Bedienungsanleitung

Vicon

Vicon Cruiser SN663V-A Bedienungsanleitung

Beliebte Sicherheitskamera Handbücher anderer Marken

Okina USA

Okina USA SIR36-870VF650LP Bedienungsanleitung

Divio

Divio NDR155PA Bedienungsanleitung

Canon

Canon VB-C500D Bedienungsanleitung

Easy Access

Easy Access EasyGuard Bedienungsanleitung

Vivotek

Vivotek FD9389-EHV-v2 Bedienungsanleitung

TUYA

TUYA COSMO W2 Bedienungsanleitung

Eusso

Eusso UNC7500-IR Einrichtungshandbuch

urmet domus

urmet domus 1096/204 Bedienungsanleitung

VC VC20 series Bedienungsanleitung

Axis

Axis Q1614 Bedienungsanleitung

ieGeek

ieGeek DD201 Bedienungsanleitung

VADDIO

VADDIO ClearVIEW HD-USB PTZ 999-6990-000 Bedienungsanleitung

Grundig

Grundig GCH-K0274P Bedienungsanleitung

Lorex

Lorex VANTAGE LBC7032 Bedienungsanleitung

4xem

4xem WPT Bedienungsanleitung

Samsung

Samsung SCV-3082 Bedienungsanleitung

Vitek

Vitek VTC-C544 Bedienungsanleitung

Lumens

Lumens VC-A50PNW Bedienungsanleitung