Viper VN1715 Bedienungsanleitung

CONGRATULATIONS on your purchase of a Viper product

and welcome to the V.I.P. family. We appreciate your

business and will do everything in our power to keep you happy

with your purchase for many years to come.

As part of the V.I.P. family, you are entitled to the best

protection by one of the most comprehensive warranties in

the industry.

Thank-you for purchasing Viper products!

Tom Vander Bie, CEO

TABLE OF CONTENTS

Safety Precautions 3

Machine Operation 4

Machine Maintenance & Storage 4

Parts List 5 - 9

Wiring Diagra 10

SAFETY PRECAUTIONS

GROUNDING INSTRUCTIONS

General –This floor – finishing machine shall be

grounded while in use to protect the operator

from electric shock. The machine is provided

with a three –conductor cord and a three contact

grounding type attachment plug to fit the proper

grounding type receptacle. The green [or green

and yellow] conductor in the cord is the

grounding wire. Never connect this wire to other

than the grounding pin of the attachment plug.

This machine is for use on a nominal 120-Volt

circuit and has a grounding plug that resembles

the plug illustrated in figure below. Make sure

that the machine is connected to an outlet

having the same configuration as the plug. No

adapter should be used with this machine.

This machine is intended for Commercial use. It

is constructed for use in an indoor environment

and is not intended for any other use. Use only

recommended accessories.

All operators shall read, understand and

exercise the following safety precautions:

1] Do not operate machine:

-Unless trained and authorized.

-Unless you have read and understand

operators manual.

-In flammable or explosive areas.

-With a damaged cord or plug.

-If not in proper operating condition.

-In outdoor areas.

-In standing water.

-With the use of extension cords.

2] Before operating machine:

-Make sure all safety devices are in place

and operate properly.

3] When using machine:

-Do not run machine over cord.

-Do not pull machine by cord or plug.

-Do not pull cord around sharp edges of

corners.

-Do not unplug by pulling on the cord.

-Do not stretch cord.

-Do not handle plug with wet hands.

-Keep cord away from heated surfaces.

-Report machine damage of faulty

operation immediately.

4] Before leaving or servicing machine:

-Turn off machine.

-Unplug cord from outlet.

5] When servicing machine:

-Unplug cord from outlet.

-Use manufacturer supplied or approved

replacements parts.

Operation of Floor Machines

* READ OPERATORS MANUAL

THOROUGHLY PRIOR TO OPERATING OR

SERVICING THIS MACHINE.

GENERAL USE

1. Remove any obstructions or other

obstacles in the area which is to be

cleaned.

2. Placethehandleintheuprightposition

and tilt machine back until handle rests

on the floor

* Be sure the machine is not plugged into

an outlet

3. Attach the pad driver or brush to the

machine by placing the clutch plate over

thegearboxhubandturningthedriver

/brush¼turn.

4. Place machine back into its upright

position.

5. Plug power cord into a grounded outlet.

* Never use an extension cord in

conjunction with the standard power cord.

6. The handle height may be adjusted by

lifting up the compression handle which

is located on the right side of the handle

tube about 1 foot above floor level.

Release the compression handle and

adjust handle to safe operating height,

then push back down on the

compression handle to lock the handle in

operating position.

7. To start the machine, press the red

safety button on the top of the upper

switch housing, and then squeeze either

of the operating triggers. (the safety

button must be depressed prior to

squeezing the operating triggers.)

8. When the machine is in operation, both

handsshouldbeplacedontheswitch

housing (upper handle).

9. During operation, to make the machine

go right, gently raise the handle. To

make the machine go left, gently lower

the handle.

10. To stop the machine at any time,

simply release the operating trigger(s)

and the machine will stop automatically.

MAINTENANCE

To keep the machine performing well for

many years, please follow the following

maintenance procedures.

* Always confirm that the machine is

unplugged prior to performing any

maintenance or repairs.

1. Unplugmachineassoonasyouare

done using it.

2. Tilt machine back and remove pad driver

or brush.

* Never store a low speed machine with

the pad driver or brush mounted to the

machine.

3. Clean the outside of the machine with a

mild cleaner.

4. Check power cord for any damage. If

damage is detected, replace power cord

immediately.

5. Lubricate wheels with a water resistant

lubricant once a month.

6. Check machine for loose or missing nuts

and bolts, and replace as necessary.

7. If the machine is used in a dusty

environment, you may remove the motor

cover and blow the motor clean with

compressed air. This will ensure proper

ventilation, and allow the motor to run

cooler.

STORAGE

1. Unplug machine from power source and

wrap cord on handle.

2. Tilt machine back and remove pad driver

or brush.

3. Store machine in upright position and in

adryarea.

DIA

PART

NUMBER

REQ'D

1VF30016 HANDLE RELEASE 1

2VF30015 BOLT, HANDLE RELEASE 1

3VF30018 WASHER, PLAIN 2

4VF13503 NUT, LOCK, M8 X 5.7 1

5VF30017 SCREW 1

6VF30014 COVER, HOOK 1

7VF45125 CORD, HANDLE 1

8AS41901 PLUG PROTECTOR, SMALL MALE 1

9VF50120A GROMMET 1

10 VF13504 NUT, LOCK, M10 1

11 VF30027 WASHER, PLAIN 1

12 VF14114 SCREW, M8 X 55 1

13 VF30013 HOOK, CORD 1

14 VF13493 SCREW, M6 X 10 1

15 AS112205 TUBE 1

16 VF44018 LEVER,SOLUTION 1

17 VV13667 SCREW, M4 X 8 2

18 VF48306 PIN 3

19 VF44016 LEVER, LEFT, SWITCH 1

20 VF45119 CORD, POWER SUPPLY 1

21 AS22009 STRAIN RELIEF, CORD 1

22 VF30108 GASKET, HANDLE, SOLUTION 1

23 VF14223 SCREW, M6 X 25 2

24 VF14218 SCREW, M6 X 45 2

25 VF13528 WASHER, TOOTH, M6 2

26 VF30102 REAR COVER, SWITCH HOUSING 1

27 VF99010C BREAKER, CIRCUIT, 17A 1

28 VF30109 COVER 1

29 GT13013 NUT, M4 3

30 VF48309 CLAMP BLOCK 1

31 VF44017 LEVER, RIGHT, SWITCH 1

32 VF44203 SWITCH ASSEMBLY 1

33 VF14212 SCREW, M3 X 25 2

34 VF13527 WASHER, TOOTH, M4 1

35 VF13526 SCREW, M4 X 30 1

36 VF46705 SAFETY BUTTON 1

37 GV40218 SPRING, SAFETY BUTTON 1

38 VF48310 HANDLE GRIP 2

39 VF30101 FRONT COVER, SWITCH HOUSING 1

40 VF47035A "VIPER" LOGO 1

41 VF13604 WASHER, TOOTH, M5 4

42 VF14222 SCREW, M5 X 12 4

HANDLE GROUP FOR VN1715 & VN2015

DESCRIPTION

DIA

PART

NUMBER

REQ'D

1GT13080 4

2VF30011 2

3VF30026 1

4VF30020 1

5VV20274 4

6GV40235 2

7VV13621 4

8VF13474A 4

9VF13613 2

10 VA13474 5

11 VF13524 4

12 VF13519 4

13 VF14114 4

14 MF-VF002-4A 6

15 MF-VF002-2 CLUTCH PLATE 1

MF-VF022 1

MF-VF021 1

17 VF999802B 1

18 VF99021 1

19 MT01102 1

VF30004 1

VF30005 1

21 VF999821A 1

22 VV13601 6

23 VV13636 SCREW, M5 X 30 6

VF30006 1

VF30006A SHROUD & BUMPER ASSY, 20-INCH 1

VF30007 VN1715 - FRAME 17-INCH 1

VF30007A SHROUD & BUMPER ASSY, 17-INCH 1

25 YLQ19200B 1

26 YCQ10501 1

27 YCQ12301 1

28 VF14549 2

29 VF30008 ALUMINIUM BASE, MOTOR 1

30 YCQ12302 STATIONARY SWITCH 1

31 VF999854 RUNNING CAPACITOR, 50μF / 370V 1

32 VF40152 HOSE BARB 1

33 YLQ14601 MOUNTING FRAME (SMALL), CAPACITOR 1

34 VF30019 BRACKET, HANDLE, RIGHT 1

35 VF13520 WASHER, LOCK 2

DESCRIPTION

SCREW, M6 X 30

CLAMP BLOCK, HANDLE

AXLE

20 VN2015 - BUMPER, 20-INCH

16 VN2015 - PAD HOLDER, 19-INCH

COUPLER

WASHER, LOCK, M5

WASHER, PLAIN, M5

SCREW, M5 X 20

SCREW, M5 X 16

WASHER, PLAIN,M8

BRACKET, LEFT HANDLE

WASHER, PLAIN, M13

CLAMP BLOCK, AXLE

SCREW, SELF-TAPPING, ST, M5 X 20

SCREW, M4 X 10

ROTOR WITH FAN ASSEMBLY

VN2015 - FRAME, 20-INCH

WASHER, LOCK, M8

SCREW, M8 X 55

VN1715 - PAD HOLDER, 16-INCH

GEAR BOX

SLEEVE

VN1715 - BUMPER, 17-INCH

BEARING,6002 LLU

BASE GROUP FOR VN1715 & VN2015

SCREW, SELF-TAPPING, 1/4"-1"

BEARING,6203 RZ

CENTRIFUGAL SWITCH

DIA

PART

NUMBER

REQ'D

36 VF50119 WASHER, PLAIN, M12 2

37 VF14214 SCREW, M5 X 8 4

38 VF48202 WHEEL, 5" 2

39 VF40994 LABEL, READ MANUAL 1

40 VF44012 SCREW, M6 X 12.7 2

41 VF13666 WASHER, M6 2

42 VF13604 WASHER, LOCK, EXTERNAL TOOTH 4

43 YCQ10615 MOUNTING FRAME (BIG), CAPACITOR 1

44 AS41902 PLUG PROTECTOR, LARGE FEMALE 1

45 YCQ10414 CLEAR COVER 4

46 YCQ10416 CAPACITOR WRAP 2

47 VF999805 1

48 YLQ17507 4

50 VF999787 MOTOR, 110V, 1.5HP 1

51 VF44003 LABEL, MOTOR 1

52 VF41079 LABEL, VIPER 1

53 VF14222 SCREW, M5 X 12 3

54 VF30001 TOP COVER, MOTOR 1

55 VF30002 CLUTCH PLATE 1

56 VF47023 1

BASE GROUP FOR VN1715 & VN2015

BUMPER

BOLT ASSEMBLY

SEE #17 & #50

START CAPACITOR (BIG), 380-400F / 150V

DESCRIPTION

Andere Handbücher für VN1715

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Viper Bodenreinigungsmaschine Handbücher

Viper

Viper Fang15B Bedienungsanleitung

Viper

Viper AS6690T Benutzerhandbuch

Viper

Viper VE 17 HS P Bedienungsanleitung

Viper

Viper CEX410 Bedienungsanleitung

Viper

Viper DR 1500 H Bedienungsanleitung

Viper

Viper SL1610SE Bedienungsanleitung

Viper

Viper AS4325B Bedienungsanleitung

Viper

Viper AS530R Benutzerhandbuch

Viper

Viper AS6690T Bedienungsanleitung

Viper

Viper SCRUBBER FANG 18C Bedienungsanleitung

Viper

Viper SCRUBBER FANG 18C Bedienungsanleitung

Viper

Viper AS710R Bedienungsanleitung

Viper

Viper FANG 20 Bedienungsanleitung

Viper

Viper FANG 20 Bedienungsanleitung

Viper

Viper VN20DS Bedienungsanleitung

Viper

Viper AS380/15 Benutzerhandbuch

Viper

Viper Dragon DR2000DC Dust Control Bedienungsanleitung

Viper

Viper AS1050R Bedienungsanleitung

Viper

Viper AS6690T Benutzerhandbuch

Viper

Viper VE 17DSP-EU Bedienungsanleitung

Viper

Viper SCRUBBER FANG 18C Bedienungsanleitung

Viper

Viper AS380/15C-EU Bedienungsanleitung

Viper

Viper AS4325B Benutzerhandbuch

Viper

Viper AS380/15B-EU Bedienungsanleitung

Beliebte Bodenreinigungsmaschine Handbücher anderer Marken

Nilfisk-Advance

Nilfisk-Advance Advance SC370 17B Bedienungsanleitung

Numatic

Numatic ET 4045 Bedienungsanleitung

HAWK ENTERPRISES

HAWK ENTERPRISES HP1513-180BRUTE Bedienungsanleitung

Mytee

Mytee 8070 Mytee-Lite Bedienungsanleitung

Kärcher

Kärcher B 140 R Bedienungsanleitung

Triple S

Triple S Ace 26T1 Bedienungsanleitung

Nilfisk-Advance

Nilfisk-Advance SW 750 Bedienungsanleitung

Tornado

Tornado Marathon 2000 98190 Handbuch

Windsor

Windsor ADMIRAL Admiral 8 Bedienungsanleitung

Numatic

Numatic TTB 1117/100 Bedienungsanleitung

Tennant

Tennant 8210D Bedienungsanleitung

Nobles

Nobles Frontier Produkthandbuch

lavina

lavina 21-X Bedienungsanleitung

KENT

KENT Edge 28B Bedienungsanleitung

Tennant

Tennant 215 Produkthandbuch

Windsor

Windsor BDP 51/2000C Bedienungsanleitung

CleanFreak

CleanFreak DURA-18HD Bedienungsanleitung

Nilfisk-Advance

Nilfisk-Advance Warrior 34RST Administratorhandbuch