Waters Shaker+ Leitfaden

USER MANUAL

Shaker+

[ CARE AND USE MANUAL ]

• The device must always be completely switched o (cables removed)

before moving it.

• The device must be handled with caution as it contains moving parts.

• The user must maintain a distance of at least 20cm from the product

(WiFi antenna) while it is being installed and operated.

• The device is intended for indoor use only.

• Device maintenance has to be done exclusively by a Waters representative.

• If the device is used in a manner not specied by the manufacturer,

the protection provided by the device may be impaired.

• All the input/output ports are Safety Extra Low Voltage (SELV) circuits.

SELV circuits should only be connected to other SELV circuits.

• To avoid damaging the unit, do not remove labware from the device if

the device’s clamps are closed. If the device’s clamps are closed onto a

labware and the device is OFF, the device must rst be turned ON.

The clamps will automatically open upon device initialization and will

thus release the labware.

• Non-slip pads are positioned below each Shaker+ Device. If any of these

pads are damaged or have been removed, they must be replaced with a

new set of pads to avoid damaging Shaker+ units.

Safety instructions

Do not touch moving parts during operation!

The user must never put their ngers or any objects on and

around the moving platform.

[ CARE AND USE MANUAL ]

About this manual

Read the user manual before using this device. Strictly follow usage and maintenance

instructions provided in the manual. It is the user’s responsibility to become familiar with all

available information concerning the correct use, care and limitations of these products.

If you are uncertain about the correct use or limitations of the products, contact Waters

service and support. The manufacturer, the distributor and their respective owners,

employees, agents and representatives are not responsible or liable for errors or omissions.

Information in this User Manual is subject to change without notice and does not represent

a commitment on the part of Waters. Waters assumes no responsibility for any inaccuracies

that may be contained in this User Manual. Waters makes no commitment to update or

keep current the information in this User Manual, and reserves the right to make improve-

ments to this User Manual and/or to the products described in this User Manual, at any time

without notice.

If you nd information in this manual that is incorrect, misleading, or incomplete,

we would appreciate your comments and suggestions.

Product

overview LED indicator Labware holder

Power socket

Ethernet port for

cable connection

Power button

Built-in

computer

Built-in wireless

adapter

Open hatch

from here

[ CARE AND USE MANUAL ]

Getting started

Plug your Shaker+

into a power source.

Wait for the LED indicator to

turn blue and blink.

After a couple of mi-

nutes, the Shaker+ will

inform you when it is

in installation mode.

Connect your computer, tablet or smartphone to the Shaker+

Launch a web browser, type http://192.168.2.1

and follow the on-screen steps to continue the installation.

A. Go to your Wi-Fi settings

and select the network named Shaker-5xx.4xxx.xxxxx

scan me

xxxx.xxxxx is the Shaker+ device serial number (you can nd it on top of your

device)

B. The LED indicator will stop blinking when the device has been successfully connected.

Shaker-5xx.4xxx.xxxxx

If the Shaker+ doesn’t automatically enter ins-

tallation mode, press the power button 5 times.

http://192.168.2.1

Before

you begin

If you do not have a OneLab account, please create one by going to:

https://onelab.andrewalliance.com/signup

The device will automatically start up.

Only use the provided AC/DC

power supply unit and cords.

Please note that the ins-

tallation page might open

automatically.

If you do not have access to a Wi-Fi

compatible device, please refer to

our online help:

help.andrewalliance.com

[ CARE AND USE MANUAL ]

45 steps

1:46:37

No additional guidelines

Simultaneous activity

None

I've made a mistake...

Continue

Next step

Pipetting

Wait for the end of shaking…

01:20

BDspl-8 BDspl-9

Shaker+ - 518.9303.XXX

Shaker+

Shaking...

1200 rpm

Step list Abort

No additional guidelines

Experiment ongoing: Cell analysis - FD12

Guidelines (optional)

Give guidelines for experiment about this

step, eg. how to proceed etc.

Drop labware you want shakehere

Duration

Speed

rpm

Labware to shake

minutes1

100 %

32 4 5 6 7 8 9 1011 12

Templateplate

50 mL tube #2 50 mL tube #3

384-well plate

50 mL tube

1 32

6-well tissue culture plate

Save step

1. Shaking Drag required labware and enter parameters for shaking

Operations

Design your protocol

Execute experiment with

Shaker+

Start the experiment and let OneLab

control your device

Our drag-and-drop editor makes it easy

to design a precise and complete protocol

with all that you need to run your

experiment perfectly.

Create a Shaking action by clicking on

this menu, which is located on the left

of the screen.

Shaking

Actions

Follow the visual instructions based on the

protocol being used and you will be guided

through your experiment.

Each step of the experiment will be recorded

and available in OneLab.

OneLab will automatically select your

Shaker+ and allows you to use it with every

available experiment set-up: manual,

semi-automated or fully automated.

Choose your desired experiment setup and

then prepare all the required materials.

Feel free to contact

the Waters

support team Send us an email to

[email protected]

Chat with our support team

directly in OneLab

We reply within 1 business day

[ CARE AND USE MANUAL ]

Technical data

Labware

compatible

Check the OneLab Domino

Catalog at andrewalliance.com/

domino-catalog

Mixing frequency • Tube: 200 to 2000 rpm

• Microplate: 200 to 3000 rpm

(The maximum speed may dier

according to the type of used

labware)

Mixing orbit

constant

2 mm

Speed setting

resolution

1 rpm

Mixing regulation

accuracy

±25 rpm

Relative humidity 80% at 37°C

Maximum

operating altitude

2000 m

Environment

temperature

operating range

+4 to +37 °C

User interface Through OneLab software

Ingress protection IP20*

Dimensions

(W x L x H)

170 x 162 x 100 mm

(The specied dimensions are

subject to change according to

the labware)

Weight 2.55 kg

External power

supply

Input 100-240 VAC, 1.4 A / out-

put 24 VDC, 5 A, 120 W

Power or

current rating

5 A

Overvoltage

category DC port

Cat I

Operating voltage 24 VDC

Network

connectivity

• Gigabit Ethernet

• Wi-Fi 2.4 GHz and 5 GHz

Pollution degree

of the intended

environment

Pollution degree 2

Cleaning Only with a wet tissue or

isopropanol

Warranty 1 year

Certications CE, FCC, RoHS, WEEE, UKCA

1. Place your connected

devices in front of Andrew+ as indicated

byOneLab.

2. Open the hatches.

3. Plug the power cables into the power sockets

of your devices.

4. Pass the cables into the dedicated channels in

front of the devices.

5. Close the hatches.

Multiple connected devices

installation

Operating device

Power on

Power o

When the device is in standby mode

(plugged into a power source but turned

o), press the power button to turn on the

device.

Note: The device will automatically start up

when you plug into a power source.

When the device is in its idle state

(no experiment running), press the

power button for 5 seconds to turn

o the device.

*Avoid spilling liquid on the device.

[ CARE AND USE MANUAL ]

Unit end of life

When a unit reaches the end of its useful life, contact Andrew Alliance for

directions and information on the end-of-life policy.

This is in accordance with the European Union Directive 2002/96/EC on

Waste Electrical and Electronic Equipment (WEEE).

Certications

Electrical safety

EMC

RADIO

FCC

RoHS

I. IEC 61010-1: 2010

II. IEC 61010-1/A1: 2016

III. UL 61010-1:2012

IV. CAN/CSA 22.2#61010-1-12

I. EN 61326-1: 2013

II. EN 301 489-1 V2.2.3

III. EN 301 489-17 V3.2.4

I. EN 300 328 Ver 2.1.1

II. EN 301 893 V2.1.1

I. FCC 47 CFR part 15 subpart B section 15.107 (b) and section 15.109 (b and g)

Class A all over other device tested per ANSI C63.4 (Ed. 2014) procedures

II. This device complies with Part 15 of the FCC Rules. Operation is subject to the

following two conditions:

(1) this device may not cause harmful interference, and (2) this device must accept

any interference received, including interference that may cause undesired opera-

tion.

RoHS 3 (EU) 2015/863

[ CARE AND USE MANUAL ]

Waters Corporation

34 Maple Street

Milford, MA 01757 U.S.A.

T: 1 508 478 2000

F: 1 508 872 1990

waters.com

Inhaltsverzeichnis

Andere Waters Laborausrüstung Handbücher

Waters

Waters Xevo G2-XS QTof Betriebsanleitung

Waters

Waters Xevo TQD Bedienungsanleitung

Waters

Waters SYNAPT G2 Bedienungsanleitung

Waters

Waters Atlantis Premier BEH C18 AX Columns Leitfaden

$Waters ACQUITY Refractive Index Detector Betriebsanleitung$

Waters

Waters ACQUITY Refractive Index Detector Betriebsanleitung

Waters

Waters Xevo TQ MS Montageanleitung

Waters

Waters ACQUITY UPLC Peptide HSS T3 100A Leitfaden

Waters

Waters Xevo TQ-S Betriebsanleitung

Waters

Waters 717plus Bedienungsanleitung

Waters

Waters Autospec Premier Handbuch

Waters

Waters SYNAPT G2 Betriebsanleitung

Waters

Waters GCT Premier Handbuch

Waters

Waters TA Instruments Sample/Temperature Stage Handbuch

Waters

Waters ACQUITY CM-30S Betriebsanleitung

Waters

Waters Anionic Polar Pesticide Column Leitfaden

Waters

Waters ACQUITY Isocratic Solvent Manager Betriebsanleitung

Waters

Waters Extraction+ Bedienungsanleitung

Waters

Waters ACQUITY UPC2 Stücklistenhandbuch

Waters

Waters Otto SPEcialist PPM Betriebsanleitung

Waters

Waters ACQUITY UPLC Betriebsanleitung

Waters

Waters Xevo TQD IVD Betriebsanleitung

Waters

Waters ACQUITY UPLC Leitfaden

Waters

Waters Xevo G2-XS QTof Betriebsanleitung

Waters

Waters Xevo TQD Betriebsanleitung

Beliebte Laborausrüstung Handbücher anderer Marken

Qiagen

Qiagen DML 3000 Bedienungsanleitung

Queensgate

Queensgate NANOSCAN OP400 Programmierhandbuch

Conviron

Conviron GEN1000-GE Bedienungsanleitung

Parr Instrument

Parr Instrument 4560 Bedienungsanleitung

IKA

IKA IC control Bedienungsanleitung

Integra

Integra DOSE IT Bedienungsanleitung

Agilent Technologies

Agilent Technologies 5800 ICP-OES Bedienungsanleitung

Endress+Hauser

Endress+Hauser Cleanfit CPA875 Bedienungsanleitung

NI PXI-5422 Handbuch

Collomix

Collomix Aqix Bedienungsanleitung

SPEX SamplePrep

SPEX SamplePrep 6875 Freezer/Mill Series Bedienungsanleitung

Ocean Insight

Ocean Insight FLAME-NIR+ Bedienungsanleitung

Parker

Parker ALIGN-MG-NA Bedienungsanleitung

BD 644787 Bedienungsanleitung

DENTAURUM

DENTAURUM Compact Megaplus Bedienungsanleitung

Biuged Laboratory Instruments

Biuged Laboratory Instruments BGD 626 Bedienungsanleitung

VWR

VWR SAS Super IAQ Bedienungsanleitung

illumina

illumina MiSeqDx Bedienungsanleitung