Wattstopper PW-301 Bedienungsanleitung

Santa Clara, CA 95050

800.879.8585

Installation Instructions

Specifications

Voltages:

PW-301 & PW-302. . . . . . . . . . . . . . . . 120/277VAC, 50/60Hz

PW-301-347 & PW-302-347. . . . . . . . . . . . 347VAC, 50/60Hz

Load Limits for relay 1:

@120VAC..1000W tungsten, ballast, E-ballast, LED, 1/4 HP

@277VAC.......... 1200W ballast, E-ballast, LED, 1/4 HP

@347VAC................... 1500W ballast, LED, 1/4 HP

Load Limits for relay 2:

@120VAC...800W tungsten, ballast, E-ballast, LED, 1/6 HP

@277VAC.......... 1200W ballast, E-ballast, LED, 1/6 HP

@347VAC................... 1500W ballast, LED, 1/6 HP

Time Delay Adjustment ....................5 to 30 minutes

Walk-Through Mode .... 3 minutes if no activity after 30 sec.

Test Mode .................. 10 min. with 5 sec. time delay

PIR Adjustment ..............................High or Low

Light Level Adjustment ......................8fc to 180+fc

Alerts ......................Selectable Audible & Visual

Optional Neutral . . . . . . . . . . . . . . . . . . . . . . . . . . . . .All models

Multi-Way Capability . . . . . . . . . . . . . . . . . . . . . . . . . All models

Terminal screw torque . . . . . . . . . . . . . . . . 16 lbf-in (18 kgf-cm)

PW-301 PW-301-347 PW-302 PW-302-347

PW-301/PW-301-347

PW-302/PW-302-347

Passive Infrared Multi-Way Wall Switch

Occupancy Sensor

Test/20 min

(DIP 1, 2, 3, OFF)

Presentation Mode is a feature of the Auto ON mode.When both relays are

manually turned OFF the PW holds the lights OFF until no motion has been

detected for the duration of the Time Delay. With subsequent occupancy, the PW

turns the load ON. If both relays are ON and one relay is manually turned OFF

this relay remains OFF until both the Time Delay and retrigger delay expires for

the relay that is ON, after that time the ON Mode control settings again apply.

Time Delays

The PW sensor holds the load ON until no motion is detected for the selected

time delay. Select the time delay using DIP switch settings. In the PW-302, both

relays use the same delay.

A Test Mode with a short time delay of 5 seconds is

set when DIP switches 1, 2, & 3 are OFF. It cancels

automatically after ten minutes, or when you set a

fixed time delay. When the Test Mode times out, the

sensor assumes a 20 minute time delay. To restart

Test Mode, change the time delay setting to any fixed

amount and then return it to the Test setting.

Walk-Through

Mode

(DIP #4 ON)

The PW sensor turns the load OFF three minutes after

the area is initially occupied, if no motion is detected

after the first 30 seconds. If motion continues beyond

the first 30 seconds, the set time delay applies.

High (DIP #5 OFF)Default setting. Suitable for most applications.

PIR Sensitivity Adjustment

The PW sensor constantly monitors the controlled environment and

automatically adjusts the PIR to avoid common ambient conditions that can

cause false detections, while providing maximum coverage.

Fixed Time Delay

(DIP 1 ON, 2 & 3 OFF)

Time delays are 5, 10, 15, 20 (default), 25, or 30

minutes.

Reduces sensitivity by approximately 50%. Useful in

cases where the PIR is detecting movement outside of

the desired area (also consider masking the lens) and

where heat sources cause unnecessary activation.

Low, 50%

(DIP #5 ON)

Visit our website for FAQs: www.wattstopper.com

Walk-Through

The Walk-Through mode shortens the time delay to reduce the amount of time

the load is ON after a brief moment of occupancy, such as returning to an office

to pick up a forgotten item then immediately exiting.

No Walk-Through

(DIP #4 OFF)

Walk-Through mode disabled.

Call 800.879.8585 for Technical Support

COVERAGE PATTERNS

Coverage testing has been

performed according to the

NEMA WD 7 guideline. For best

performance, use in spaces not

larger than 15’ x 12’.

PIR Sensor

The sensor has a two-tiered,

multi-cell viewing Fresnel lens with

180 degree field of view. The red

LED on the sensor flashes when the

PIR detects motion.

Masking the lens

Opaque adhesive tape is supplied

so that sections of the PIR sensor’s

view can be masked. This allows

you to eliminate coverage in

unwanted areas. Since masking

removes bands of coverage, remember

to take this into account when

troubleshooting coverage

problems.

PIR

Coverage

7.5’

(2.2m)

15’

(4.5m)

20’

(6.1m)

35’

(10.6m)

Major motion

Minor motion

Alerts

The PW can provide audible and/or visible alerts as a warning before the load

turns OFF.

Unit will beep at one minute*, at 30 seconds and at 10

seconds before turning OFF load. When Walk-Through

is active, the unit beeps three times at 10 seconds

before the load goes OFF.

*If Visible Alert is also ON, the one-minute time-out

warning beep is replaced by the visible alert.

Audible Alerts

(DIP #7 ON)

No audible warnings provided.

When only one minute is left in the time delay, the

load connected to the relay turns OFF for one second.

This provides a one minute warning before the load(s)

are turned OFF by the sensor.

Visible Alert

(DIP #6 ON)

No Visible Alerts

(DIP #6 OFF)

No visible warnings provided.

No Audible Alerts

(DIP #7 OFF)

4’

(1.2m)

20’

(6.1m)

35’

(10.6m)

Top View

Side View

1. Make sure that the power has been turned OFF at the circuit breaker.

2. Connect wires to the PW flying leads as shown in the

wiring diagram that is appropriate to the PW model and

electrical supply. The 2 ground wires (both green) must

be fastened to ground for the sensor to work properly.

3. Attach the sensor to the wall box by inserting screws into

the two wide holes on the top and bottom of the attached

metal bracket. Match them up with the holes in the wall

box and tighten.

4. Turn the circuit breaker ON. Wait

one minute, then push the Auto

ON/OFF switch for each load and

the lights will turn ON. There is

a delay due to initial power-up of

the sensor that only occurs during

installation.

5. Test and adjust the sensor if

necessary.

6. Install industry standard

decorator wall switch cover plate

(not included).

INSTALLATION

Red

Black

Neutral

Line

Green

Ground

Blue

Primary

Load

Secondary

Load

Neutral

(optional)

Brown

Yellow

Red

Black

Neutral

Line 1

Green

Ground

Blue

Primary

Load

Brown Secondary

Load

Line 2

Neutral

(optional)

Yellow

PW-302 and PW-302-347

Bi-Level Wiring

PW-302 and PW-302-347

Dual Circuit Wiring

WARNING

TURN THE POWER OFF AT THE CIRCUIT BREAKER

BEFORE INSTALLING THE SENSOR OR WORKING ON THE LOAD.

#12 – #14 AWG

Cu Wire Only

Strip Gage

1/2"

12.7mm

Visit our website for FAQs: www.wattstopper.com

Load

Red

Black

Neutral

Line

Green

Neutral

(optional)

Ground

Yellow

PW-301 and PW-301-347 Wiring

Side View

Optional Neutral Wiring

For applications requiring

neutral wiring, remove tab

as shown to expose

terminals for wiring. If connected,

the unit will work in full function

mode. If disconnected, the device

will function as a two-wire device.

Breakaway

tab

Optional neutral

terminals behind

breakaway tab

6" ying leads for

line, load, ground

and multi-way

connections

Multi-Way

The Multi-Way capability is available on all models. Sensors can easily be

wired together for convenient control of a common load. When wiring this

way, only use 300 series sensors. Multi-Way in 300 series is not compatible

with prior sensor models.

The following princlples apply for Multi-Way:

• All units can see each other’s push button events and respond accord-

ingly.

• All units can see each other’s PIR trigger event. The response will be

determined by the Light Level setting and/or conditions of the space of

the detecting sensor.

• The time delay for all units is deﬁned by the unit with the smallest time

delay.

Call 800.879.8585 for Technical Support

Black Load

Red

Black

Neutral

(optional)

Line

Neutral

(optional)

Ground

Green

Ground

Green

Yellow

traveler

Yellow

Red

Typical wiring

(PW-301 or PW-301-347-up to 4 sensors)

Visit our website for FAQs: www.wattstopper.com

Sensor Operating Modes

Sensor #1 Sensor #2 Light Fixture

Auto-ON Auto-ON The load turns ON and OFF automatically

based on occupancy detection by either one

of the sensors. The sensors keep the load

ON until no motion is detected and will use

the time delay of the sensor with the lowest

value. At any time, the light can be turned

ON and OFF using the ON/OFF button of any

one of the sensors. If the load is turned OFF

manually by pressing either one of the ON/

OFF buttons, the unit will enter Presentation

mode.

Auto-ON* Manual-ON* The load can only be turned ON automati-

cally by the sensor set in Auto-ON mode. The

sensors keep the load ON until no motion is

detected and will use the time delay of the

sensor with the lowest value. There is either

a 30 second re-trigger delay for the sensor

set in Manual-ON mode or instant re-trigger

for the sensor set in Auto-ON mode. After

the re-trigger delay elapses, the ON/OFF

button of the sensor set in Manual-ON mode

must be pressed to turn the load back on un-

less the sensor set in Auto-ON mode detects

motion. If the light is turned OFF manualy by

pressing the ON/OFF button set in Auto-ON,

it will enter Presentation mode.

Manual-ON Manual-ON The occupant must press the ON/OFF button

on either one of the sensors to turn the light

ON. The sensors keep the load ON until no

motion is detected and will use the time de-

lay of the sensor with the lowest value. There

is a 30 second re-trigger delay, meaning the

occupant has 30 seconds to be detected for

the sensor to turn the load back on auto-

matically. After the re-trigger delay elapses,

the ON/OFF button of any one of the sensors

must be pressed to turn the load back ON.

* Although this conﬁguration may be selected, it is not recommended.

Call 800.879.8585 for Technical Support

Bi-level wiring

(PW-302 or PW-302-347 - up to 4 sensors)

Note: Button 1 on any sensor controls load #1 and button 2 on any

sensor controls load #2.

Two-phase wiring

Black Black

Neutral

(optional)

Line

Yellow

Red Primary

Load

Brown Secondary

Load

Neutral

(optional)

Ground

Green

Ground

Green

Red

Brown

Blue Blue

Black Black

Neutral

Ground

Green

Neutral

(optional)

Line 1

Yellow

Red Primary

Load

Brown Secondary

Load

Neutral

(optional)

Blue Blue

Green

Ground

Green

Red

Brown

Line 2

Neutral

UNIT DESCRIPTION AND OPERATION

The PW Passive Infrared Wall Switch sensors use advanced passive infrared

(PIR) technology.

The PW sensor has Optional Neutral capability for applications requiring

neutral wiring. It also has Multi-Way available on all models. A “walk-through”

mode can turn lights off after only 3 minutes, if no activity is detected after 30

seconds following an occupancy detection.

The PW-301 has one relay and one ON/OFF button. The PW-302 contains

two relays and two ON/OFF buttons to allow control of one or two loads

independently. Pressing a button toggles the state of the corresponding relay.

PW sensors contain a light level sensor. If adequate daylight is present, the

sensor holds the load OFF until light levels drop, even if the area is occupied. In

the PW-302, light level only affects the load on Relay 2. Users can overrule the

hold OFF function by pressing the ON/OFF button. See Light Level Adjustment.

Turning Load(s) ON (ON Mode)

The relays are programmed independently for either Auto ON or Manual ON. In

either mode, the load can be turned ON or OFF using the ON/OFF button.

Manual ON

DIP 8 ON

for Relay 1

DIP 9** ON

for Relay 2

With an ON Mode DIP switch in the ON position, the occupant

must press the ON/OFF button to turn ON the load. The sensor

keeps the load ON until no motion is detected for the selected

time delay. There is a 30 second re-retrigger delay. If occupancy

is detected during the delay, the sensor turns the load back ON.

After the re-trigger delay elapses the ON/OFF button must be

pressed to turn ON the load.

** PW-301: Switch 9 is not used. PW-302: Switch 9 default is ON to comply

with CA Energy Commission Title 24 bi-level switching requirements.

Auto ON

DIP 8 OFF for

Relay 1

DIP 9** OFF

for Relay 2

With an ON Mode DIP switch in the OFF position, the load turns

ON and OFF automatically based on occupancy. If the load is

turned OFF manually, Presentation Mode operation applies. This

prevents the load from turning ON automatically after it was

deliberately turned OFF. Pressing the button to turn lights ON

returns the sensor to Auto ON mode.

Shading indicates default operation and switch setting.

Model # Relay Default ON Mode DIP switch # Setting

PW-301 1 Manual ON 8 ON

PW-301-347 1 Manual ON 8 ON

PW-302 1 Auto ON 8 OFF

2 Manual ON 9 ON

PW-302-347 1 Auto ON 8 OFF

2 Manual ON 9 ON

DELAY

PIR 50%

WALK

AUD. ALERT

RLY 1 MAN

RLY 2 MAN

VIS. ALERT

ON/OFF Buttons

Relay 1

Relay 2

DIP Switches

PIR Lens

Detection LED

DIP SWITCH SETTINGS

=ON =OFF

Auto On

Manual On

Relay 1 Mode

High

Low, 50%

PIR Sensitivity

Disabled

Enabled

Audible Alert

Disabled

Enabled

Walk-Through

12345678

Time

Delay

Walk-Through

Relay 1 Mode

Relay 2 Mode

Audible Alerts

PIR Sensitivity

Visible

Alerts

Test/20 min

10 minutes

15 minutes

20 minutes

25 minutes

30 minutes

Service

5 minutes

123

Time Delay

Service bypasses occupancy

& light level functions. Control the

load manually using ON/OFF button.

Disabled

Enabled

Visible Alert

PW-302 ONLY

Auto On

Manual On

Relay 2 Mode

Factory Settings:

All models

PW-301 series

PW-302 series

Call 800.879.8585 for Technical Support

Button

Hinges

Tabs

PW-302 shown.

PW-301 has a

single button.

TROUBLESHOOTING

Lights do not turn ON with motion (LED does flash)

1. Press and release each button to make sure that the correct lights come

ON for each relay. If the lights do NOT turn ON, check wire connections,

especially the Load connection. If the lights turn ON, verify that the

correct On Mode is selected in DIP switches 8 and 9.

2. Check to see if light level control is enabled: cover the sensor lens with

your hand. If the lights come ON, adjust the light level setting.

3. If lights still do not turn ON, call 800.879.8585 for technical support.

Lights do not turn ON with motion (LED does not flash)

1. Press and release each button to make sure that the correct lights come

ON for each relay. If the lights turn ON, verify that Sensitivity is on High.

2. Check the wire connections, in particular, the Line connection. Verify that

connections are tightly secured.

3. If lights still do not turn ON, call 800.879.8585 for technical support.

ADJUSTMENTS

Sensor Adjustment

Remove the wall plate. Remove the button cap by firmly squeezing together the

top sides of the button assembly. Gently pull it away from the unit.

When the adjustments are completed, replace the button cap by inserting its

hinges into the tabs on the main unit and then squeeze the top of the button while

pressing it into the unit. Reinstall the cover plate.

Light Level Adjustment

The light level can be set with loads ON or OFF. To enable light level control and

set the threshold: 1) Make sure the room is lit appropriately. 2) Put the sensor

into TEST mode (see Time Delay switches). You have 10 minutes to complete the

procedure. 3) Press and hold the ON/OFF button (Relay 1button on the PW-302)

for 3 seconds, until you hear a beep. 4) Step away from the sensor. After 10

seconds a beep sounds, indicating that the threshold level is set. This threshold

is retained, even if power is lost, until it is re-set or disabled. In the PW-302, light

level control only affects Relay 2.

To disable light level control, press and hold the Relay 1button for 7 seconds,

until a double beep tone sounds.

Reset to Default

Use the DIP Switch Settings tables on the previous page to return features

to factory settings. To reset the PW press and hold the Relay 1button for 10

seconds, until a triple beep sounds. This resets the sensor and disables light

level control (the brightest ambient light will not hold the light OFF).

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere wattstopper Zubehör Handbücher

wattstopper

wattstopper LMLS-400 Bedienungsanleitung

wattstopper

wattstopper DT-200 Bedienungsanleitung

wattstopper

wattstopper WN-100 Bedienungsanleitung

wattstopper

wattstopper DW-200 Bedienungsanleitung

wattstopper

wattstopper CI-300 Bedienungsanleitung

wattstopper

wattstopper CI-200 Bedienungsanleitung

wattstopper

wattstopper CI-24 Bedienungsanleitung

wattstopper

wattstopper FS-705 Bedienungsanleitung

wattstopper

wattstopper W-500A Bedienungsanleitung

wattstopper

wattstopper CI-200 Bedienungsanleitung

wattstopper

wattstopper EW-200-120 Bedienungsanleitung

wattstopper

wattstopper FM-105 Bedienungsanleitung

wattstopper

wattstopper FSP-211 Bedienungsanleitung

wattstopper

wattstopper DSW-301 Bedienungsanleitung

wattstopper

wattstopper RH-250 Bedienungsanleitung

wattstopper

wattstopper RD‑250 Bedienungsanleitung

wattstopper

wattstopper DT-355 Bedienungsanleitung

wattstopper

wattstopper CD-250 Bedienungsanleitung

wattstopper

wattstopper LMPX-100-4 Bedienungsanleitung

wattstopper

wattstopper EW-205-24 Bedienungsanleitung

wattstopper

wattstopper PW-100 Bedienungsanleitung

wattstopper

wattstopper DSW-301 Bedienungsanleitung

wattstopper

wattstopper RH-250-W Bedienungsanleitung

wattstopper

wattstopper WS-301 Service-Handbuch

Beliebte Zubehör Handbücher anderer Marken

Hillco

Hillco 2810 Bedienungsanleitung

Siemens

Siemens QSA2700D Bedienerhandbuch

Contours

Contours ZY024 Bedienungsanleitung

Saivod

Saivod VS621 Bedienungsanleitung

Virtuox

Virtuox VirtuCLEAN 2.0 Bedienungsanleitung

SCE

SCE ENVIRO-THERM SCE-TE170B24VSS Bedienungsanleitung

Z-Wave

Z-Wave HSD-200Z Bedienungsanleitung

turck

turck FMX-IM-2UPLI63FX Bedienungsanleitung

Decagon Devices

Decagon Devices 10HS Bedienungsanleitung

UPPAbaby

UPPAbaby Cup Holder Bedienungsanleitung

Elko

Elko SmartSensor Leakage Wireless Bedienungsanleitung

Grizzly

Grizzly H8371 Bedienungsanleitung

Panasonic

Panasonic HG-T Series Bedienungsanleitung

IFM Electronic

IFM Electronic Efector 250 Series Referenzhandbuch

DigiDesign

DigiDesign 888/24 I/O Bedienungsanleitung

PROZIS

PROZIS QUAY Bedienungsanleitung

patagonia

patagonia PSI Vest Bedienungsanleitung

SFC Energy

SFC Energy EFOY GO! Bedienungsanleitung

wattstopper PW-301 Bedienungsanleitung

Beliebte Zubehör Handbücher anderer Marken