Weider Pro 9625 Bedienungsanleitung

PATENT PENDING

WELDER

Model No. 831.159360

Serial No.

The serial number can be found in the

location shown below. Write the serial

number in the space above.

Serial Number Decal

F" x E: R C i _._,E:

Eq3, U I P M E N T

HELPLINEI

1-800-736-6879

USER'S MANUAL

a_AUTION- SEARS

BEARB, ROEBUCK AND CO., HOFFMAN ESTATES, IL 60179

TABLE OF CONTENTS

IMPORTANT PRECAUTIONS ............................................................. 2

BEFORE YOU BEGIN ................................................................... 3

ASSEMBLY ........................................................................... 4

ADJUSTMENT ........................................................................ 19

TROUBLE-SHOOTING AND MAINTENANCE ......... ....................................... 22

CABLE DIAGRAM ..................................................................... 23

ORDERING REPLACEMENT PARTS ................................................. Back Cover

FULL 90 DAY WARRANTY ....................................................... Back Cover

Note: An EXPLODED DRAWING/PART LIST and a PART IDENTIFICATION CHART are attached to the center

of this manual, Remove the EXPLODED DRAWING/PART LIST and the PART IDENTIFICATION CHART before

beginning assembly.

7. The be

time.

oAlwya stand on a foot plate when perform-

1, Ing an exeralee th_ _ld _use the home

9Ymay stern to tip. _, _

11. Never release the press arm, butterfly arms,

squst arm, leg lever, tat bar, or nylon strap

while weights are raised, The weights will fall

with great force.

12. Make sure that the cables remain onthe pul-

leys at all times. If the cables bind while you

are exercising, stop Immediately and make

sure that the cables are on all of the pulleys.

13. Always disconnect the let bar from the home

_oymsystem when oerformlno an exerciQe

that does not use the let bar.

BEFORE YOU BEGIN

Thank you for selecting the WELDER= PRO 9625

Home Gym System. The versatile PRO 9625 is

designed to develop every major muscle group of the

body. Whether your goal is a shapely figure, dramatic

muscle size and strength, or a healthier cardiovascular

system, the PRO 9625 will help you to achieve the

specific results you want.

For your benefit, read this manual carefully before

using the WELDER=PRO 9625 Home Gym System.

If you have additional questions, please call our toll-

free HELPLINE at 1-800-736-6879, Monday through

Saturday, 7 a.m, until 7 p.m. Central Time (excluding

holidays). To help us assist you, please note the prod-

uct model number and serial number before calling.

The model number is 831.159360. The serial number

can be found on a decal attached to the WELDER=

PRO 9625 (see the front cover of this manual).

Before reading further, please review the drawing

below and familiarize yourself with the parts that are

labeled.

ASSEMBLED

DIMENSIONS:

Height: 76 in.

Width: 38 in.

Length: 59 in.

High Pulley Station

Lat Bar

Butterfly Arms

Squat

Weight

Press Arm

Leg Lever

Low Pulley Station

- Foot Plate

ASSEMBLY

Before beginning assembly, carefully read the

following Information and Instructions:"

• Place all parts of the home gym system in a

cleared area and remove the packing materials;

do not dispose of the packing materials until

assembly is completed.

• The assembly is divided into four stages: 1)

frame assembly, 2) press, squat, and butterfly

arm assembly, 3) cable and pulley assembly, and

4) seat and backrest assembly. The hardware for

each stage is packaged separately.

• Wait until you begin each assembly stage to open

that parts bag.

• For help identi_ing the small parL_used in

assembly, use the PART IDENTIFICATION

CHART located In the center of this manual.

Note: Some smal_parts may have been pre*

attached for shipping. If a part is not in the parts

bag, check to see if it has been pre-attashed.

•As you assemble the home gym system, be sure

that all parts are oriented as shown in the

drawings.

•"Tightenall parts as you assemble them, unless

Instructed to do otherwise.

THE FOLLOWING TOOLS (NOT INCLUDED) ARE

REQUIRED FOR ASSEMBLY:

•Two (2) adjustable wrenches

•One (1) standard screwdriver

•One (1) phillips screwdriver

•One (1) rubber mallet

•Lubdcent, such as grease or petroleum jelly,

and soapy water will also be needed.

Assembly will be more convenient ifyou have the

following tools: A socket set, a set of open-end or

closed-end wrenches, or a set of ratchet wrenches.

_i_ _¸_¸¸ _!

1. Before beginning assembly, be sure that

you have read and understand the Infor-

mation In the box above.

Press a 2" Square Inner Cap (27) intothe

end of the Rear Base (51). Press a 2" Square

Cover Cap (78) onto each end of the

Stabilizer (5).

Insert two 5/16" x 2 1/2" Carriage Bolts (1)

up through the Rear Base (51). Insert two

5/16" x 2 3/4" Bolts(11) through the Rear

Base and Stabilizer (5) as shown,

2. Press a 2" Square Inner Cap (27) intothe

end of the Front Base (4).

Insert two 5/16" x 2 112"Carriage Bolts (1)

up through the Front Base (4), Slide the

Front Base ontothe two 5/16" x 2 3/4" Bolts

(11) in the Rear Base (51) and Stabilizer (5).

Hand-tighten two 5/16" Nylon Locknuts (3)

onto the Carriage Bolts. Do not tighten the

Nylon Locknuts yet.

11 78

11' 1

11 ":'__. 4

3. Press a 2" Square Inner Cap (27)into the 3

Rear Upright (56),

!_IM i

!i_i!t,_ 4.

_iii_ i__i_i_

!iiilil

Attach a Rubber Bumper (90) to the Rear

Upright (56) with a #8 x 112"Tap Screw (89).

Slide the Rear Llpright (56) onto the 5/16" x

2 1/2" Carriage Bolts (1) in the Rear Base

(51). Hand tighten a5/16" Nylon Locknut (3)

onto each Carriage Bolt. The high side of

the bracket on the Rear Upright must be

on the side shown. Do not tighten the

Nylon Locknuts yet.

Press a 1" Square Inner Cap (65) into the

Front Upright (42).

Slide the Front Upright (42) onto the 5/16" x

2 1/2" Carriage Bolts (1) in the Front Base

(4). Hand tighten a5/16" Nylon Locknut (3)

onto each Cardage Bolt. Do not tighten the

Nylon Locknute yet.

h Side of

Bracket

;-J

!iii i _ii_i_ i_i

ii_ii_ i_:_i_i!iiii_

ill _:_!_iiii_i

!i!!_i!__i!_ii_

__iii_ii_ii_

_i_ _ i_i

,Set two Weight Bumpers (19) onto the bracket

on the Stabilizer (5). Insert bothWeight Guides

through the Weight Bumpers and the bracket

on the Stabilizer. Be sure that the drilled

holes In the Weight Guides are at the top,

as shown. Press a 1" Round Cover Cap (70)

onto the bottom of each Weight Guide (62).

Slide eight Weights (25) on the Weight

Guides (62). Be sure that all of the Weights

are turned so the pin grooves are on the

same side.

.Press the Weight Tube Bumper (64) intothe

end of the Weight Tube (63). Insert the

Weight Tube into the stack of Weights (25).

Be sure that the pins on the Weight Tube are

resting in the pin grooves in the upper

Weight.

Lubricate the insides of the holes in the Top

Weight (76). Slide the Top Weight onto the

Weight Guides (62) and set it on the stack of

Weights (25).

.Press a 2" Square Inner Cap (27) into each.

end of the Top Frame (55). Press a 1 3/4"

Square Inner Cap (44) into each end of the

crossbar on the Top Frame. Press two 1"

Round Inner Caps (49) into the top of the

crossbar.

Attach the Top Frame (55) to the Front Upright

(42) and the Rear Upright (56) with four 5/16"

x 2 3/4" Bolts (11), four 5/16" Flat Washe_'s

(8), and four 5/16" Nylon Locknuts (3).

Drilled holes must

7be at the top

762

Pin Grooves must

be on this side

:: 8. Attach the upper ends of the Weight Guides

(62) to the Top Frame (55) with the 5/16" x 6"

Bolt (60), two 1/2" x 3/4" Spacers (61), and a

5/16" Nylon Locknut (3).

i ¸ Ul

Tighten all Nylon Locknute used In steps 2

through 6.

i!!!iiiiiiii!iii!!il110

Press a 1"x 7/8" Plastic Bushing (75) onto

each welded spacer on the Press Frame (17).

Slide the Press Frame into place on the Front

Base (4). Note: This will be a fight fit. The

Plastic Bushings should fit onto each end

of the indicated tube in the Base. Be sure

that the indicated pulleys are on the side

shown.

Lubricate the 3/8" x 8" Bolt (59). Attach the

Press Frame (17) to the Front Base (4) with

the 3/8" x 8" Bolt and a 3/8" Nylon Locknut

(21).

Press a I 3/4" Square Inner Cap (44) intothe

top of a Press Arm (46). Press a 1" Round

Inner Cap (49) into the side of the Press Arm.

Attach the Press Arm to one side of the Press

Frame (17) with two 5116"x 2 1/2" Bolts (22)

and two 5116"Nylon Locknuts (3).

Assemble the other Press Arm (46) in the

same manner.

ii!iiiiiiiiii_ili_i;iiiiii!_

i!!iiiiiiii!!iiliil11.

iiiiliili

ii ¸

Identify the Right Arm (48) and the LeftArm

(47). Note the position Ofthe welded bracket

on each Arm. Arm Identification Is very

Important for step 12.

Note: The "V"-Pulleys (6), Long Cable Traps

(50), 3/8" x 2 1/2" Bolts (7), and 3/8" Nylon

Locknuts (21) are pre-attached. These have

been shown disassembled for easy part iden-

tification.

i;!;i_i!i:ii;iii!

3 . ,

Tube

11 _7_-_50

We,ded // 47

Brackets_ '_21

ii ¸

{ i ¸¸ :=i

i ¸

12. Lubricate both axles on the Top Frame (55),

Slide the Right Arm (48) onto the right axle.

Note: Be careful not to confuse the Right

Arm with the Left Arm (47); refer to step 11

to Identify the Right Arm. Be sure that the

upper end of the Right Arm is behind the

indicated bracket on the Top Frame (55).

Tap two 1" Retainers (69) and a 1" Round

Cover Cap (70) onto the right axle. Be sure

that the teeth on the Retainers bend

toward the Cover Cap, as shown In the

Inset drawing.

Attach the Lef_Arm (47) in the same manner.

Press 1 3/4" Square Inner Caps (44) into the

lower ends of the Right and LeftArms (47,

48). Wet the lower end of each Arm with

soapy water. Slide a10" Pad (45) onto the

lower end of each Arm,

13. Press two 1"x 2" Inner Caps (83) intothe

indicated end of the Squat Arm (79).

Attach the Squat Arm (79) to the Front

Upright (42) with a 3/8" x 3 1/4" Bolt (85) and

a3/8" Nylon Locknut (21).

Attach a Handle (92) to one side of the Squat

Arm (79) with a 5/16" x 2 1/2" Bolt (22), two

5/16" Rat Washers (8_ a 1/2"x 17132"Spacer

(94), and a 5/16" Nylon Locknut (3).

Attach the other Handle (92) to the other side

of the Squat Arm (79) in the same manner.

22 92

83 -8

94 3

ii_ _i _

During steps 15 through 36, refer to the

CABLE DIAGRAM on page 23 of this manual

to verify proper cable routing. Before begin-

ning this section, identify the Long Cable (86),

the Medium Cable (23), and the Short Cable

(58) by comparing the lengths and ends of the

cables.

IMPORTANT: While assembling the cables,

do not overtlghten the bolts and nuts

securing the pulleys. The pulleys must be

able to turn freely.

15. Locate the Medium Cable (23). Wrap the

Medium Cable around a 3 1/2" Pulley (15).

Attach the Pulley to the Top Frame (55) with a

3/8" x 3 3/4" Bolt (71) and a 3/8" Nylon

Locknut (21). Be sure that the end of the

Cable with the ball Is on the indicated side

....... of the Pulley and that the Cable is between

the Pulley and the hook.

iiiiiili_ii!1 16. Wrap the Medium Cable (23) around a =V"-

Pulley (6). Attach the "V_-Pulley and a Long

ii!!!!i<lCi!

Cable Trap (50) to the indicated bracket on

the Front Upright (42) with a 3/8" x 2 1/2" Bolt

(7) and a 3/8" Nylon Locknut (21). Be sure

that the Long Cable Trap Is positioned to

hold the Cable In place.

iii!ili!!!i!iiiii

17. Route the Medium Cable (23) around the =V"-

Pulley (6) on the Left Arm (47). Be sure that

the Cable Is In the groove of the Pulley and

that the Long Cable Trap (50) Is positioned

to hold the Cable In place. Tighten the 3/8" x

2 112"Bolt (7) and the 3/8" Nylon Locknut (not

shown).

_ _ '' _-86 (174")

:_ _ _-_-,_23 (159")

:L u , 58 (47")

21_

;5 ._'-23

Hook 71 //

7---q

6 7 50

18. Route the Medium Cable (23) around the =V-

Pulley (6) on the Right Arm (48). Be sure

that the Cable Is In the groove of the "V"-

Pulley and that the Long Cable Trap (50) Is

turned to hold the Cable In place, "13ghten

the 3/8" x 2 1/2, Bolt (7) and the 3/8" Nylon

Locknut (not shown).

19. Route the Medium Cable (23) around the

3 1/2, Pulley (15) attached to the Pulley

Bracket (20). Be sure that the Cable Is In

the groove of the Pulley and that the Cable

Trap (66) is turned to hold the Cable in

place. Tighten the 3/8" x 2" Bolt (12) and the

3/8" Nylon Locknut (not shown).

Be sure that the 5/16" x 5" Bolt (68) is proper-

ly tightened and that the Pulley Bracket (20)

can move freely.

20. Route the Medium Cable (23) around one of

the 3 1/2" Pulleys (15) attached to the =1"

Plates (81). Be sure that the Cable is in the

groove of the Pulley and that the Cable

and Pulley move smoothly,

Andere Handbücher für Pro 9625

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Weider Heim-Fitnessstudio Handbücher

Weider

Weider Pro 335 Bedienungsanleitung

Weider

Weider 831.15969.0 Bedienungsanleitung

Weider

Weider 8950 Kurzanleitung

Weider

Weider Pro 9950 Bedienungsanleitung

Weider

Weider 325 Bench Bedienungsanleitung

Weider

Weider MAX XP400 Bedienungsanleitung

Weider

Weider PRO 260 Bedienungsanleitung

Weider

Weider 9000 Bench Bedienungsanleitung

Weider

Weider C241 Installationsanleitung

Weider

Weider CROSS BOW WESY59420 Bedienungsanleitung

Weider

Weider WESY39522 Bedienungsanleitung

Weider

Weider 831.150380 Bedienungsanleitung

Weider

Weider Pro 400L Bedienungsanleitung

Weider

Weider Pro 525 Bedienungsanleitung

Weider

Weider Platinum Plus WESY7974.0 Bedienungsanleitung

Weider

Weider 831.159833 Bedienungsanleitung

Weider

Weider Flex 2000 Plus Bedienungsanleitung

Weider

Weider PRO 408 Bedienungsanleitung

Weider

Weider Pro 125 Bench Kurzanleitung

Weider

Weider 9400 PRO Bedienungsanleitung

Weider

Weider WESY19720 Bedienungsanleitung

Weider

Weider 9900i Benutzerhandbuch

Weider

Weider Flex 108 Wt Bench Bedienungsanleitung

Weider

Weider 9900i Bedienungsanleitung

Beliebte Heim-Fitnessstudio Handbücher anderer Marken

Horizon Fitness

Horizon Fitness OXFORD 6 Bedienungsanleitung

Energetics

Energetics Multi Trainer 5.1 Bedienungsanleitung

Matrix

Matrix MG-PL Series Bedienungsanleitung

Reebok

Reebok Tbr2i Bedienungs- und Wartungshandbuch

Pure Fitness

Pure Fitness 8526HE Bedienungsanleitung

Bowflex

Bowflex Sport 001-6961 Bedienungsanleitung

NordicTrack

NordicTrack E8200 Competition Bench Kurzanleitung

Body Solid

Body Solid GHYP-345 Bedienungsanleitung

Evo

Evo TAHOE 5105 Bedienungsanleitung

cardiobull

cardiobull RA17 Bedienungsanleitung

ParaBody

ParaBody 40 Bedienungsanleitung

JLL

JLL Ventus Pro Air Power Bedienungsanleitung

Trojan

Trojan Colorado 370 Bedienungsanleitung

Octane Fitness

Octane Fitness xRide xR650 Bedienungsanleitung

Precor

Precor Discovery Series Bedienungsanleitung

Insportline

Insportline RW600 Bedienungsanleitung

Stamina

Stamina 55-1532 Bedienungsanleitung

Tunturi

Tunturi R25 Bedienungsanleitung