Weider Pro 9950 Bedienungsanleitung

USER’S MANUAL

Model No. 831.159530

Serial No.

The serial number is found in the

location shown below. Write the

serial number in the space above.

CAUTION

Read all precautions and instruc-

tions in this manual before using

this equipment. Save this manu-

al for future reference.

Serial Number Decal

Patent Pending

Visit our website at

www.weiderfitness.com

new products, prizes,

fitness tips, and much more!

SEARS, ROEBUCK AND CO.

HOFFMAN ESTATES, IL 60179

IMPORTANT PRECAUTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

BEFORE YOU BEGIN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

ASSEMBLY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5

ADJUSTMENT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

WEIGHT RESISTANCE CHART . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .25

CABLE DIAGRAMS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .26

TROUBLE-SHOOTING AND MAINTENANCE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .27

ORDERING REPLACEMENT PARTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Back Cover

FULL 90-DAY WARRANTY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Back Cover

Note: A PART LIST/EXPLODED DRAWING and a PART IDENTIFICATION CHART are attached in the center of

this manual. Remove the PART LIST/EXPLODED DRAWING and the PART IDENTIFICATION CHART before

beginning assembly.

TABLE OF CONTENTS

1. Read all instructions in this manual and in

the accompanying literature before using the

weight system.

2. It is the responsibility of the owner to ensure

that all users of the weight system are ade-

quately informed of all precautions.

3. The weight system is intended for home use

only. Do not use the weight system in a com-

mercial, rental, or institutional setting.

4. Use the weight system only on a level sur-

face. Cover the floor or carpet beneath the

weight system to protect the floor or carpet.

5. Make sure all parts are properly tightened

each time you use the weight system.

Replace any worn parts immediately.

6. Keep children under the age of 12 and pets

away from the weight system at all times.

7. The weight system is designed to be used by

no more than two people at a time.

8. Always wear athletic shoes for foot protec-

tion when exercising.

9. Keep hands and feet away from moving parts.

10. Make sure the cables remain on the pulleys

at all times. If the cables bind while you are

exercising, stop immediately and make sure

the cables are on all of the pulleys.

11. Always stand on the foot plate when perform-

ing an exercise that could cause the weight

system to tip.

12. Never release the press arms, butterfly arms,

leg lever, lat bar, or ab strap while weights

are raised. The weights will fall with great

force.

13. Always disconnect the lat bar or ab strap

from the weight system when performing an

exercise that does not use the attachments.

14. If you feel pain or dizziness at any time while

exercising, stop immediately and begin cool-

ing down.

15. Do not place more that 200 pounds on either

weight carriage. Always place the same

amount of weight on both sides of each

weight carriage.

16. The warning decals

shown here have

been placed on the

weight system in the

locations shown on

page 4. Note that

decal 1 has been

placed in two loca-

tions. If a decal is

missing or illegible,

please call our toll-

free HELPLINE at

1-800-736-6879,

Monday through

Saturday, 7 a.m. until

7 p.m. Central Time,

to order a free

replacement decal.

Place the decal on

the weight system in

the location shown.

WARNING: To reduce the risk of serious injury, read the following important precau-

tions before using the weight system.

WARNING: Before beginning this or any exercise program, consult your physician. This

is especially important for persons over the age of 35 or persons with pre-existing health problems.

Read all instructions before using. SEARS assumes no responsibility for personal injury or property

damage sustained by or through the use of this product.

IMPORTANT PRECAUTIONS

Keep hands and

fingers clear of

this area.

Decal 1

Decal 2

ASSEMBLED

DIMENSIONS:

Height: 77 in.

Width: 103 in.

Depth: 55 in.

Low Pulley

Station

Foot Plate

Leg Lever

Press Arms

Decal 1

Decal 2

Backrest

Curl Pad

Butterfly Arms

Ab Pulley Station

Leg Press Arm

Thank you for selecting the innovative and versatile

WEIDER®PRO 9950 weight system. The WEIDER®

PRO 9950 offers a unique selection of weight stations

designed to develop every major muscle group of the

body. Whether your goal is to tone your body, build

dramatic muscle size and strength or improve your

cardiovascular system, the WEIDER®PRO 9950

makes it easy to achieve the results you want.

For your benefit, read this manual carefully before

using the WEIDER®PRO 9950 weight system. If you

have additional questions, please call our toll-free

HELPLINE at 1-800-736-6879, Monday through

Saturday, 7 a.m. until 7 p.m. Central Time (excluding

holidays). To help us assist you, please note the prod-

uct model number and serial number before calling.

The model number is 831.159530. The serial number

can be found on a decal attached to the weight system

(see the front cover of this manual).

Please use the drawing below to familiarize your-

self with the major parts and how they fit together.

Leg Press Plate

Weight Carriage

Backrest

Seat

High Pulley

Station

Lat Bar

BEFORE YOU BEGIN

Make sure you have the following tools:

• Two adjustable wrenches

• One standard screwdriver

• One phillips screwdriver

• One rubber mallet

• You will also need grease or petroleum jelly, a

small amount of soapy water, and clear tape or

masking tape.

Note: Assembly will be more convenient if you have

a socket set, a set of open-end or closed-end

wrenches, or a set of ratchet wrenches.

How to Identify Parts

To help you identify the small parts used in assembly,

we have included a PART IDENTIFICATION CHART

in the center of this manual. Place the chart on the

floor and use it to easily identify parts during each

assembly step. Note: Some small parts may have

been pre-attached. If a part is not in the parts

bag, check to see if it has been pre-attached.

How to Orient Parts

As you assemble the weight system, make sure that

all parts are oriented exactly as shown in the draw-

ings.

Tightening Parts

Tighten all parts as you assemble them, unless

instructed to do otherwise.

Questions?

If you have questions after reading the assembly

instructions, please call our HELPLINE at

1-800-736-6879.

Assembly Requires Two Persons

For your convenience and safety, assemble the

weight system with the help of another person.

Set Aside Enough Time

Due to the many features of the weight system, the

assembly process will take time. By setting aside

plenty of time and by deciding to make the task

enjoyable, assembly will go smoothly. You may want

to assemble the weight system over a couple of

evenings.

Select a Location for the Weight System

Because of its weight and size, the weight system

should be assembled in the location where it will be

used. Make sure that there is enough room to walk

around the weight system as you assemble it.

How to Unpack the Box

To make assembly as easy as possible, we have

divided the assembly process into four stages. The

parts needed for each stage are found in individual

bags. Important: Wait until you begin each stage

to open the parts bag for that stage. Place all

parts of the weight system in a cleared area and

remove the packing materials. Do not dispose of

the packing materials until assembly is completed.

Make Assembly Easier for Yourself

Everything in this manual is designed to

ensure that the weight system can be assem-

bled successfully by anyone. Before begin-

ning assembly, make sure to read the

information on this page. This brief intro-

duction will save you much more time than

it takes to read it.

The Four Stages of the Assembly Process

Frame Assembly—You will begin by assembling

the base and the uprights that form the skeleton of

the weight system.

Arm Assembly—During this stage you will

assemble the arms and the leg lever.

Cable Assembly—During this stage you will

attach the cables and pulleys that connect the

arms to the weights.

Seat Assembly—During the final stage you will

assemble the seats and the backrests.

ASSEMBLY

1. Before beginning, make sure that you have

read and understood the information on page 5.

Locate and open the parts bags labeled

“FRAME ASSEMBLY 1 and 2.”

Press a 2” Square Inner Cap (59) into each end

of the Butterfly Base (1).

Insert four 5/16” x 2 1/2” Carriage Bolts (54) up

through the Butterfly Base (1). Place the Butterfly

Base flat on the floor. Note: If the Bolts fall out,

secure them with a small piece of tape.

Attach the Center Base (2) to the Butterfly Base

(1) with two 5/16” x 2 3/4” Bolts (55), a Long

Support Plate (34), and two 5/16” Nylon Locknuts

(64). Do not tighten the Nylon Locknuts yet.

2. Press a 2” Square Inner Cap (59) into each end

of the Press Base (3).

Insert four 5/16” x 2 1/2” Carriage Bolts (54) and

two 3/8” x 2 1/2” Carriage Bolts (76) up through

the Press Base (3). Place the Press Base flat on

the floor. Note: If the Bolts fall out, secure

them with a small piece of tape.

Attach the Press Base (3) to the Center Base (2)

with two 5/16” x 2 3/4” Bolts (55), a Long Support

Plate (34), and two 5/16” Nylon Locknuts (64). Do

not tighten the Nylon Locknuts yet.

3. Orient the Butterfly Upright (4) as shown. Attach

the Butterfly Upright to the indicated 5/16” x 2

1/2” Carriage Bolts (54) in the Butterfly Base (1)

with two 5/16” Nylon Locknuts (64). Do not tight-

en the Nylon Locknuts yet.

Frame Assembly

55 34

4. Press a 1 1/2” Square Inner Cap (100) into the

indicated part of the Press Upright (6).

Orient the Press Upright (6) as shown. Attach the

Press Upright to the indicated 5/16” x 2 1/2”

Carriage Bolts (54) in the Press Base (3) with two

5/16” Nylon Locknuts (64).

Attach the Support Brace (7) to the indicated 3/8”

x 2 1/2” Carriage Bolts (76) in the Press Base (3)

with two 3/8” Nylon Locknuts (74).

Attach the Support Brace (7) to the Press Upright

(6) with two 5/16” x 2 1/2” Carriage Bolts (54) and

two 5/16” Nylon Locknuts (64).

Do not tighten the Nylon Locknuts (64, 74) yet.

5. Press two 1” Inner Caps (32) into the ends of the

weight tube on a Weight Carriage (28).

If you will be using Olympic weights with the

weight system, slide a Weight Sleeve (27) onto

each end of the weight tube on the Weight

Carriage (28). Secure each Weight Sleeve with a

Locking Pin (31). Note: The drawings in this

manual show the Weight Sleeves attached.

The Locking Pins will be found in the bag

labled “SEAT ASSEMBLY”.

Repeat this step with the other Weight Carriage

(28).

100

74 74

32 31

354

Weight Tube

6. Press a Weight Bumper (56) onto each bumper

tube on the Center Base (2). Press a 1 1/2”

Round Inner Cap (67) into each bumper tube.

Attach two Weight Guides (33) to the indicated

tube in the Center Base (2) with a 3/8” x 6” Bolt

(89) and a 3/8” Nylon Locknut (74).

Attach the other set of Weight Guides (33) in the

same manner.

Do not tighten the 3/8” Nylon Locknuts (74)

yet.

Bumper

Tube

8. Attach the Top Frame (5) to the Butterfly Upright

(4) with two 3/8” x 2 3/4” Bolts (58), a Short

Support Plate (26), and two 3/8” Nylon Locknuts

(74). Note: Be sure that the Top Frame is ori-

ented with the long bracket on the side

shown, and that it rests between the Weight

Guides (33) as shown in step 9.

Attach the Top Frame (5) to the Press Upright (6)

in the same manner.

Do not tighten the 3/8” Nylon Locknuts (74) yet.

9. Attach each set of Weight Guides (33) to the Top

Frame (5) with a 3/8” x 6” Bolt (89) and a 3/8”

Nylon Locknut (74). Do not tighten the Nylon

Locknuts yet.

7. Slide a Weight Carriage (28) onto each set of

Weight Guides (33). Be sure the weight tubes

are near the top of the Weight Carriages

Long Bracket

Weight

Tube

10. Press three 2” Square Inner Caps (59) into the

Butterfly Top Frame (19).

Attach the Butterfly Top Frame (19) to the

Butterfly Upright (4) with two 5/16” x 2 3/4” Bolts

(55), a Long Support Plate (34), and two 5/16”

Nylon Locknuts (64).

Attach the Butterfly Top Frame (19) to the Top

Frame (5) with two 5/16” x 2 3/4” Bolts (55), a

Long Support Plate (34), and two 5/16” Nylon

Locknuts (64).

Do not tighten the 5/16” Nylon Locknuts (64)

yet.

464

Adjustment knob

must be on this side

72 3

64 66

11. Press a 2” Square Inner Cap (59) into the Press

Top Frame (13).

Attach the Press Top Frame (13) to the Press

Upright (6) with two 5/16” x 2 3/4” Bolts (55), a

Long Support Plate (34), and two 5/16” Nylon

Locknuts (64).

Attach the back hole on the side of the Press Top

Frame (13) to the Top Frame (5) with a 5/16” x 2

3/4” Bolt (55), the Pulley Support Plate (107), and

a 5/16” Nylon Locknut (64).

Attach the next hole on the side of the Press Top

Frame (13), a 3 1/2” Pulley (37) and a Cable Trap

(44) to the Top Frame (5) with a 3/8” x 4” Bolt

(91), the Pulley Support Plate (107), and a 3/8”

Nylon Locknut (74). Do not overtighten the

Nylon Locknut; the Pulley must be able to turn

easily.

Do not tighten the Nylon Locknuts (64, 74) yet.

107

12. Attach a Bumper (71) to the Press Seat Frame

(12) with a Bumper Screw (72).

Attach the Press Seat Frame (12) to the 5/16” x

2 1/2” Carriage Bolts (54) in the Press Base (3)

with two 5/16” Nylon Locknuts (64).

Attach the Press Seat Frame (12) to the Press

Upright (6) with two 5/16” x 2 3/4” Bolts (55), two

5/16” Washers (66), and two 5/16” Nylon

Locknuts (64).

Do not tighten the 5/16” Nylon Locknuts (64)

yet.

13. Attach the Butterfly Seat Frame (10) to the

Butterfly Front Leg (9) with two 5/16” x 2 3/4”

Bolts (55), two 5/16” Washers (66), and two 5/16”

Nylon Locknuts (64). Do not tighten the Nylon

Locknuts yet. Be sure the Adjustment Knob

(not shown) is on the indicated side.

14. Attach a Bumper (71) to the Butterfly Front Leg

(9) with a Bumper Screw (72).

Attach the Butterfly Front Leg (9) to the 5/16” x

2 1/2” Carriage Bolts (54) in the Butterfly Base (1)

with two 5/16” Nylon Locknuts (64).

Attach the Butterfly Seat Frame (10) to the

Butterfly Upright (4) with two 5/16” x 2 3/4” Bolts

(55), two 5/16” Washers (66), and two 5/16”

Nylon Locknuts (64).

Tighten all of the Nylon Locknuts (64, 74)

used in steps 1 to 14.

Axle

15. Locate and open the parts bag labeled “ARM

ASSEMBLY.”

Press a 2” Square Inner Cap (59) into each end

of the Leg Lever (8).

Lubricate the 3/8” x 3 1/4” Bolt (101). Attach the

Leg Lever (8) to the Butterfly Front Leg (9) with

the Bolt and a 3/8” Nylon Jamnut (88).

16. Press two 1 3/4” Square Inner Caps (60) into the

ends of the the Right Butterfly Arm (18). Press

two Handgrips (99) onto the handle on the Right

Butterfly Arm.

Assemble the Left Butterfly Arm (17) in the same

manner.

Handle

17. Lubricate both axles on the Butterfly Top Frame

(19). Slide the Right Butterfly Arm (18) onto the

indicated axle. Be sure the upper end of the

Butterfly Arm is behind the bracket on the

Butterfly Top Frame.

Tap two 1” Retainers (85) and a 1” Round Cover

Cap (86) onto the axle. Be sure that the teeth

on the Retainers bend toward the Round

Cover Cap, as shown in the inset drawing.

Attach the Left Butterfly Arm (17) in the same

manner.

86 17

101

59 88

Arm Assembly

Lubricate

Bracket

Axle

Inhaltsverzeichnis

Andere Weider Heim-Fitnessstudio Handbücher

Weider

Weider Club 500 Bench Bedienungsanleitung

Weider

Weider 140 WEIGHT BENCH COMBO Bedienungsanleitung

Weider

Weider 831.153972 Bedienungsanleitung

Weider

Weider WEBE0635.0 Bedienungsanleitung

Weider

Weider Body Works Pro 2.0 Bench Bedienungsanleitung

Weider

Weider Pro 305 Bedienungsanleitung

Weider

Weider Pro 125 Bench Bedienungs- und Wartungshandbuch

Weider

Weider Pro 132 Bedienungsanleitung

Weider

Weider WESY86303 Bedienungsanleitung

Weider

Weider Body Works Pro 2.0 Bench Bedienungsanleitung

Weider

Weider Pro 120 Bench Benutzerhandbuch

Weider

Weider B460 Bench Bedienungsanleitung

Weider

Weider 9250 Bedienungs- und Wartungshandbuch

Weider

Weider 245 Bench Kurzanleitung

Weider

Weider Flex 8960 Bedienungs- und Wartungshandbuch

Weider

Weider Flex 8960 Bedienungsanleitung

Weider

Weider Pro 9835 Bedienungsanleitung

Weider

Weider 9000 Bench Benutzerhandbuch

Weider

Weider Pro 290 wc bench Bedienungsanleitung

Weider

Weider WEMC10161 Bedienungsanleitung

Weider

Weider Pro 3000 Bedienungs- und Wartungshandbuch

Weider

Weider D480 Bedienungsanleitung

Weider

Weider 170 Tc Bench Benutzerhandbuch

Weider

Weider 9900i Einrichtungshandbuch

Beliebte Heim-Fitnessstudio Handbücher anderer Marken

Horizon Fitness

Horizon Fitness OXFORD 6 Bedienungsanleitung

Energetics

Energetics Multi Trainer 5.1 Bedienungsanleitung

Matrix

Matrix MG-PL Series Bedienungsanleitung

Reebok

Reebok Tbr2i Bedienungs- und Wartungshandbuch

Pure Fitness

Pure Fitness 8526HE Bedienungsanleitung

Bowflex

Bowflex Sport 001-6961 Bedienungsanleitung

NordicTrack

NordicTrack E8200 Competition Bench Kurzanleitung

Body Solid

Body Solid GHYP-345 Bedienungsanleitung

Evo

Evo TAHOE 5105 Bedienungsanleitung

cardiobull

cardiobull RA17 Bedienungsanleitung

ParaBody

ParaBody 40 Bedienungsanleitung

JLL

JLL Ventus Pro Air Power Bedienungsanleitung

Trojan

Trojan Colorado 370 Bedienungsanleitung

Octane Fitness

Octane Fitness xRide xR650 Bedienungsanleitung

Precor

Precor Discovery Series Bedienungsanleitung

Insportline

Insportline RW600 Bedienungsanleitung

Stamina

Stamina 55-1532 Bedienungsanleitung

Tunturi

Tunturi R25 Bedienungsanleitung