Weider WESY19720 Bedienungsanleitung

USER’S MANUAL

QUESTIONS?

As a manufacturer, we are com-

mitted to roviding com lete

customer satisfaction. If you have

questions, or find there are miss-

ing or damaged arts, we will

guarantee you com lete satisfac-

tion through direct assistance

from our factory.

TO AVOID UNNECESSARY

DELAYS, PLEASE CALL DIRECT

TO OUR TOLL-FREE CUSTOMER

HOT LINE. The trained techni-

cians on our customer hot line

will rovide immediate assis-

tance, free of charge to you.

CUSTOMER HOT LINE:

1-800-999-3756

Mon.–Fri., 6 a.m.–6 .m. MST

Model No. WESY19720

Serial No.

Write the serial number in the space

above for reference.

Serial Number Decal

CAUTION

Read all recautions and instruc-

tions in this manual before using

this equi ment. Save this manual

for future reference.

Visit our website at

www.weiderfitness.com

new products, prizes,

fitness tips, and much more!

TABLE OF CONTENTS

IMPORTANT PRE AUTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3

BEFORE YOU BEGIN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4

ASSEMBLY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5

ADJUSTMENTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17

TROUBLESHOOTING AND MAINTENAN E . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19

ABLE DIAGRAM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20

PART LIST . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .22

EXPLODED DRAWING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .23

ORDERING REPLA EMENT PARTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Back over

LIMITED WARRANTY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Back over

Note: A PART IDENTIFI ATION HART is attached to the center of this manual. Remove the PART

IDENTIFI ATION HART before beginning assembly.

WEIDER is a registered trademark of I ON Health & Fitness, Inc.

IMPORTANT PRECAUTIONS

WARNING: To reduce the risk of serious injury, read the following im ortant recautions

before using the weight system.

1. Read all instructions in this manual and in

the accom anying literature before using the

weight system.

2. It is the res onsibility of the owner to ensure

that all users of the weight system are ade-

quately informed of all recautions.

3. The weight system is intended for home use

only. Do not use the weight system in any

commercial, rental, or institutional setting.

4. Use the weight system only on a level sur-

face. Cover the floor beneath the weight sys-

tem to rotect the floor.

5. Make sure all arts are ro erly tightened

each time you use the weight system.

Re lace any worn arts immediately.

6. Kee children under 12 and ets away from

the weight system at all times.

7. Kee hands and feet away from moving arts.

8. Always wear athletic shoes for foot rotection.

9. The weight system is designed to su ort a

a maximum user weight of 300 ounds.

10. Always stand on the foot late when er-

forming an exercise that could cause the

weight system to ti .

11. Never release the ress arm, butterfly arms,

leg lever, lat bar, or nylon stra while weights

are raised. The weights will fall with great

force.

12. Always disconnect the lat bar from the

weight system when performing an exercise

that does not use the lat bar.

13. Make sure that the cables remain on the ul-

leys at all times. If the cables bind while you

are exercising, sto immediately and make

sure that the cables are on all of the ulleys.

14. If you feel ain or dizziness at any time while

exercising, sto immediately and begin cool-

ing down.

15. The decals shown

here have been

laced on the

weight system in the

locations shown on

age 4. If a decal is

missing or illegible,

lease call our

Customer Service

De artment toll-free

at 1-800-999-3756,

Monday through

Friday, 6 a.m. until 6

.m. Mountain Time,

to order a free

re lacement decal.

A ly the re lace-

ment decal in the

location shown.

WARNING:Before beginning this or any exercise rogram, consult your hysician. This

is es ecially im ortant for ersons over the age of 35 or ersons with re-existing health roblems.

Read all instructions before using. ICON assumes no res onsibility for ersonal injury or ro erty

damage sustained by or through the use of this roduct.

Keep hands and

fingers clear of

this area.

Decal 1

Decal 2

BEFORE YOU BEGIN

ASSEMBLED

DIMENSIONS:

Height: 76 in.

Width: 38 in.

Length: 53 in.

Foot Plate Low Pulley Station

High Pulley Station

Lat Bar

Leg Lever

Butterfly Arm

Press Arm

Weight Stack

Seat

Backrest

Warning

Decal 1

Warning

Decal 2

Weight Pin

Thank you for selecting the versatile WEIDER®8515

weight system. The WEIDER®8515 weight system

offers a selection of weight stations designed to devel-

op every major muscle group of the body. Whether

your goal is to tone your body, build dramatic muscle

size and strength, or improve your cardiovascular sys-

tem, the WEIDER®8515 weight system will help you to

achieve the specific results you want.

For your benefit, read this manual carefully before

using the weight system. If you have additional

questions, please call our ustomer Service

Department toll-free at 1-800-999-3756, Monday

through Friday, 6 a.m. until 6 p.m. Mountain Time

(excluding holidays). To help us assist you, please

note the product model number and serial number

before calling. The model number is WESY19720. The

serial number can be found on a decal attached to the

weight system (see the front cover of this owner's

manual).

Before reading further, please review the drawing

below and familiarize yourself with the parts that are

labeled.

ASSEMBLY

High Side of

Bracket

51 14

127

Before beginning assembly, carefully read the

following information and instructions:

•Place all parts of the weight system in a cleared

area and remove the packing materials; do not

dispose of the packing materials until assembly is

completed.

• The assembly is divided into four stages: 1)

frame assembly, 2) press and butterfly arm

assembly, 3) cable and pulley assembly, and 4)

seat and backrest assembly. The hardware for

each stage is packaged separately.

• Wait until you begin each assembly stage to open

that parts bag.

•For help identifying the small parts used in

assembly, use the PART IDENTIFICATION

CHART located in the center of this manual.

Note: Some small parts may have been pre-

attached for shipping. If a part is not in the parts

bag, check to see if it has been pre-attached.

•As you assemble the weight system, be sure that

all parts are oriented as shown in the drawings.

•Tighten all parts as you assemble them, unless

instructed to do otherwise.

THE FOLLOWING TOOLS (NOT INCLUDED) ARE

REQUIRED FOR ASSEMBLY:

• Two (2) adjustable wrenches

• One (1) standard screwdriver

• One (1) hilli s screwdriver

• One (1) rubber mallet

• Lubricant, such as grease or etroleum jelly,

and soa y water will also be needed.

Assembly will be more convenient if you have the

following tools: A socket set, a set of open-end or

closed-end wrenches, or a set of ratchet wrenches.

1. Before beginning assembly, be sure that

you have read and understand the infor-

mation in the box above.

Press a 2” Square Outer ap (51) onto each

end of the Stabilizer (5). Press a 2” Square

Inner ap (27) into the end of the Base (4).

Insert two M8 x 67mm arriage Bolts (14)

up through the Stabilizer (5). Insert two M8 x

63mm arriage Bolts (1) up through the

Base (4).

Slide the indicated end of the Base (4) onto

the M8 x 67mm arriage Bolts (14) in the

Stabilizer (5). Slide the Rear Upright (56)

onto the arriage Bolts. Hand tighten a M8

Nylon Locknut (3) onto each arriage Bolt.

The high side of the bracket on the Rear

U right must be on the side shown. Do

not tighten the Nylon Locknuts yet.

FRAME ASSEMBLY

2. Slide the Front Upright (42) onto the M8 x

63mm arriage Bolts (1) in the Base (4).

Hand tighten an M8 Nylon Locknut (3) onto

each arriage Bolt. Do not tighten the

Nylon Locknuts yet.

Press a 1” Square Inner ap (65) into the

Front Upright (42).

3. Press a 2” Square Inner ap (27) into each

end of the Top Frame (55). Press a 1 3/4”

Square Inner ap (44) into each end of the

crossbar on the Top Frame. Press two 1”

Round Inner aps (49) into the top of the

crossbar.

Attach the Top Frame (55) to the Front Upright

(42) and the Rear Upright (56) with four M8 x

65mm Bolts (11), four 5/16” Flat Washers (8),

and four M8 Nylon Locknuts (3).

Tighten all Nylon Locknuts used in ste s 1

through 3.

4. Set two Weight Bumpers (19) onto the brack-

et on the Base (4) as shown.

Stack six Weights (25) on the Weight

Bumpers (19). Be sure that all of the Weights

are turned so the pin grooves are on the

same side. Be careful not to ti the stack

of Weights.

11 11

56 42

rossbar

Pin Groove

4—Bracket

FRAME ASSEMBLYARM ASSEMBLY

5. Press the Weight Tube Bumper (64) into the

end of the Weight Tube (63). Insert the

Weight Tube into the stack of Weights (25).

Be sure that the pins on the Weight Tube are

aligned with the pin grooves in the upper

Weight.

Lubricate the insides of the holes in the Top

Weight (76). Set the Top Weight onto the

stack of Weights (25).

Insert both Weight Guides (62) into the stack

of Weights (25). Be sure that the holes in

the Weight Guides are at the to , as

shown.

6. Attach the upper ends of the Weight Guides

(62) to the Top Frame (55) with the m8 x

150mm Bolt (60), two 1/2” x 3/4” Spacers

(61), and an M8 Nylon Locknut (3).

Be sure that the Pulley Bracket (20) is in

front of the right Weight Guide (62) as

shown.

7. Press a 1” x 7/8” Plastic Bushing (75) onto

each welded spacer on the Press Frame (17).

Slide the Press Frame into place on the Base

(4). Note: This will be a tight fit. The

Plastic Bushings should fit onto each end

of the indicated tube in the Base. Be sure

that the ulleys are on the indicated side.

Lubricate the M10 x 195mm Bolt (59). Attach

the Press Frame (17) to the Base (4) with the

M10 x 195mm Bolt and an M10 Nylon

Locknut (21).

Lubricate

60 20

4—Tube Welded

Spacers

Lubricate

Pulleys

Holes

ARM ASSEMBLY

8. Press a 1 3/4” Square Inner ap (44) into the

top of a Press Arm (46). Press a 1” Round

Inner ap (49) into each end of the handle on

the Press Arm. Attach the Press Arm to one

side of the Press Frame (17) with two M8 x

62mm Bolts (22) and two M8 Nylon Locknuts

(3).

Assemble the other Press Arm (46) in the

same manner.

9. Identify the Right Arm (48) and the Left Arm

(47). Note the position of the welded bracket

on each Arm. Arm identification is very

im ortant for ste 10.

Note: The “V”-Pulleys (6), Long able Traps

(50), M10 x 60mm Bolts (7), and M10 Nylon

Locknuts (21) are pre-attached. These have

been shown disassembled for easy part iden-

tification.

10. Lubricate both axles on the Top Frame (55).

Slide a 1/8” x 2 1/2” Plastic Bushing (74) onto

the right axle.

Slide the Right Arm (48) onto the right axle.

Note: Be careful not to confuse the Right

Arm with the Left Arm (47); refer to ste 9

to identify the Right Arm. Be sure that the

u er end of the Right Arm is behind the

indicated bracket on the To Frame (55).

Tap two 1” Retainers (69) and a 1” Round

over ap (70) onto the right axle. Be sure

that the teeth on the Retainers bend

toward the Cover Ca , as shown in the

inset drawing.

Attach the Left Arm (47) in the same manner.

Press 1 3/4” Square Inner aps (44) into the

lower ends of the Right and Left Arms (47,

48). Wet the lower end of each Arm with

soapy water. Slide a 10” Pad (45) onto the

lower end of each Arm.

Bracket

Lubricate Axle

Welded

Brackets 21

CABLE ASSEMBLY

11. During steps 11 through 25, refer to the

ABLE DIAGRAM on page 20 of this manual

to verify proper cable routing. Before begin-

ning this section, identify the Long able (23)

and the Short able (58) by comparing the

lengths of the cables.

IMPORTANT: While assembling the cables,

do not overtighten the bolts and nuts

securing the ulleys. The ulleys must be

able to turn freely.

12. Locate the Long Cable (23). Route the Long

able around the indicated 3 1/2” Pulley (15)

attached to the Top Frame (55). Be sure that

the end of the Cable with the ball is on the

indicated side of the Pulley and that the

Cable is between the Pulley and the hook.

Tighten the M10 x 90mm Bolt (77) and the

M10 Nylon Locknut (not shown).

13. Wrap the Long able (23) around a “V”-Pulley

(6). Attach the “V”-Pulley and a Long able

Trap (50) to the indicated bracket on the

Front Upright (42) with a M10 x 60mm Bolt

(7) and an M10 Nylon Locknut (21). Be sure

that the Long Cable Tra is ositioned to

hold the Cable in lace.

14. Route the Long able (23) around the “V”-

Pulley (6) on the Left Arm (47). Be sure that

the Cable is in the groove of the Pulley

and that the Long Cable Tra (50) is osi-

tioned to hold the Cable in lace. Tighten

the M10 x 60mm Bolt (7) and the M10 Nylon

Locknut (not shown).

Hook

Ball 15

650

15. Route the Long able (23) around the “V”-

Pulley (6) on the Right Arm (48). Be sure

that the Cable is in the groove of the “V”-

Pulley and that the Long Cable Tra (50) is

turned to hold the Cable in lace. Tighten

the M10 x 60mm Bolt (7) and the M10 Nylon

Locknut (not shown).

16. Route the Long able (23) around the 3 1/2”

Pulley (15) attached to the Pulley Bracket

(20). Be sure that the Cable is in the

groove of the Pulley and that the Cable

Tra (66) is turned to hold the Cable in

lace. Tighten the M10 x 45mm Bolt (78) and

the M10 Nylon Locknut (not shown).

Be sure that the M8 x 115mm Bolt (68) is

properly tightened and that the Pulley Bracket

(20) can move freely.

17. See the inset drawing. Attach a 3 1/2” Pulley

(15) and a able Trap (66) to the indicated

hole in the Long “U”-Bracket (57) with a M10

x 50mm Bolt (12) and an M10 Nylon Locknut

(21). Be sure that the Cable Tra is inside

the “U”-Bracket. Note: This may come re-

assembled.

Route the Long able (23) around the 3 1/2”

Pulley (15) and through the Long “U”-Bracket

(57). Be sure that the Cable is in the

groove of the Pulley and that the Cable

and Pulley move smoothly.

18. Note: The Pulley (15) in this drawing is

re-assembled. It is shown disassembled

for easy art identification.

Route the Long able (23) around the 3 1/2”

Pulley (15) attached to the bracket on the Top

Frame (55). Tighten the M10 x 45mm Bolt

(78) and the M10 Nylon Locknut (21). Be

sure that the Cable is in the groove of the

Pulley and that the Cable and Pulley move

smoothly.

CABLE ASSEMBLY

50 76

21 12

Bracket

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Weider Heim-Fitnessstudio Handbücher

Weider

Weider Platinum 800 WESY75740 Bedienungsanleitung

Weider

Weider WESY19510 Bedienungsanleitung

Weider

Weider WESY68632 Bedienungsanleitung

Weider

Weider Pro 125 Bench Bedienungsanleitung

Weider

Weider Pro 235 831.150300 Bedienungsanleitung

Weider

Weider Pro 240 831.150312 Bedienungsanleitung

Weider

Weider 8920 Bedienungsanleitung

Weider

Weider WEBE05590 Bedienungsanleitung

Weider

Weider 8980 I Bedienungsanleitung

Weider

Weider Pro 290 wc bench Bedienungsanleitung

Weider

Weider Flex 225 Bedienungsanleitung

Weider

Weider COBRA Bedienungsanleitung

Weider

Weider 150722 Bedienungsanleitung

Weider

Weider Pro 300 Bedienungsanleitung

Weider

Weider 831.159833 Bedienungsanleitung

Weider

Weider PRO 900 Bedienungsanleitung

Weider

Weider 8700 I Bedienungs- und Wartungshandbuch

Weider

Weider 8950 Bedienungsanleitung

Weider

Weider WEMC10161 Bedienungsanleitung

Weider

Weider Club C 240 Bench Bedienungsanleitung

Weider

Weider WESY29521 Bedienungsanleitung

Weider

Weider 831.159010 Bedienungsanleitung

Weider

Weider 195 Tc Bench Systemhandbuch

Weider

Weider XT20 Bedienungsanleitung

Beliebte Heim-Fitnessstudio Handbücher anderer Marken

Horizon Fitness

Horizon Fitness OXFORD 6 Bedienungsanleitung

Energetics

Energetics Multi Trainer 5.1 Bedienungsanleitung

Matrix

Matrix MG-PL Series Bedienungsanleitung

Reebok

Reebok Tbr2i Bedienungs- und Wartungshandbuch

Pure Fitness

Pure Fitness 8526HE Bedienungsanleitung

Bowflex

Bowflex Sport 001-6961 Bedienungsanleitung

NordicTrack

NordicTrack E8200 Competition Bench Kurzanleitung

Body Solid

Body Solid GHYP-345 Bedienungsanleitung

Evo

Evo TAHOE 5105 Bedienungsanleitung

ParaBody

ParaBody 40 Bedienungsanleitung

JLL

JLL Ventus Pro Air Power Bedienungsanleitung

Trojan

Trojan Colorado 370 Bedienungsanleitung

Octane Fitness

Octane Fitness xRide xR650 Bedienungsanleitung

Precor

Precor Discovery Series Bedienungsanleitung

Insportline

Insportline RW600 Bedienungsanleitung

Stamina

Stamina 55-1532 Bedienungsanleitung

Tunturi

Tunturi R25 Bedienungsanleitung

CYBEX

CYBEX Jungle Gym 17000 Bedienungsanleitung