Weider WESY92190 Bedienungsanleitung

USERÕS MANUAL

Model No. WESY92190

Serial No.

The serial number is found in the

location shown below. Write the

serial number in the space above.

CAUTION

Read all precautions and instruc-

tions in this manual before using

this equipment. Save this manu-

al for future reference.

QUESTIONS?

As a manufacturer, we are com-

mitted to providing complete

customer satisfaction. If you

have questions, or if there are

missing parts, we will guarantee

complete satisfaction through

direct assistance from our factory.

TO AVOID UNNECESSARY

DELAYS, PLEASE CALL DIRECT

TO OUR TOLL-FREE CUSTOMER

HOT LINE. The trained techni-

cians on our customer hot line

will provide immediate assis-

tance, free of charge to you.

CUSTOMER HOT LINE:

1-800-999-3756

Mon.ÐFri., 6 a.m.Ð6 p.m. MST

Patent Pending

Visit our website at

www.weiderfitness.com

new products, prizes,

fitness tips, and much more!

Serial

Number

Decal

Important Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

Before You Begin . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Cable Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

How to Use the Weight System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

Trouble-shooting and Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

Ordering Replacement Parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Back Cover

Limited Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Back Cover

Note: A PART LIST/EXPLODED DRAWING and a PART IDENTIFICATION CHART are attached to the center of

this manual. Remove the PART LIST/EXPLODED DRAWING and the PART IDENTIFICATION CHART before

beginning assembly.

Table of Contents

WARNING: Before beginning this or any exercise program, consult your physician. This is especially

important for persons over the age of 35 or persons with pre-existing health problems. Read all

instructions before using. ICON assumes no responsibility for personal injury or property damage

sustained by or through the use of this product.

Important Precautions

1. It is the responsibility of the owner to ensure

that all users of the weight system are ade-

quately informed of all precautions.

2. Read all instructions in this manual and in

the accompanying literature before using the

weight system.

3. If you feel pain or dizziness at any time while

exercising, stop immediately and begin cool-

ing down.

4. Use the weight system only on a level sur-

face. Cover the floor or carpet beneath the

weight system for protection.

5. Inspect and tighten all parts often. Replace

any worn parts immediately.

6. Make sure the cables remain on the pulleys

at all times. If the cables bind while you are

exercising, stop immediately and make sure

the cables are on all of the pulleys.

7. Always stand on the foot plate when perform-

ing an exercise that could cause the weight

system to tip.

8. Keep children under the age of 12 and pets

away from the weight system at all times.

9. Keep hands and feet away from moving parts.

10. The weight system is designed to be used by

only one person at a time.

11. Always wear athletic shoes for foot protec-

tion when exercising.

12. Always disconnect the lat bar or row bar

from the weight system when performing an

exercise that does not use them.

13. Keep the power cord away from heated sur-

faces.

14. The weight system is intended for home use

only. Do not use the weight system in a com-

mercial, rental, or institutional setting.

15. The decals

shown at the

right have

been placed

on the weight

system in the

five locations

shown on

page 4. If a

decal is miss-

ing or illegible,

please call the

customer hot

line listed on

the front cover

of this manual

to order a free

replacement

decal. Apply

the decal in

the location

shown.

To reduce the risk of serious injury, read the following important precau-

tions before using the weight system.

WARNING:

ASSEMBLED

DIMENSIONS:

Height: 77 in.

Width: 38 in.

Length: 61 in.

Low Pulley

Station

Warning

Decal 2

Foot Plate

Row Bar

Console

High Pulley

Station

Ab Pulley

Station

Leg Lever

Butterfly Arm

Press Arm

Shroud

Warning Decal 2

(on both sides of the

weight mechanism

inside of the shroud)

Warning Decal 1

Seat

Backrest

Thank you for selecting the versatile WEIDER¨E2000.

The E2000 offers a selection of weight stations

designed to develop every major muscle group of the

body. Whether your goal is to tone your body, build

dramatic muscle size and strength, or improve your

cardiovascular system, the E2000 will help you to

achieve the results you want.

For your benefit, read this manual carefully before

using the WEIDER¨E2000. If you have additional

questions, please call our Customer Service

Department toll-free at 1-800-999-3756, Monday

through Friday, 6 a.m. until 6 p.m. Mountain Time

(excluding holidays). To help us assist you, please

note the product model number and serial number

before calling. The model number is WESY92190. The

serial number can be found on a decal attached to the

E2000 (see the front cover of this manual).

Please use the drawing below to familiarize your-

self with the major parts and how they fit together.

Before You Begin

Curl Pad

Lat Bar

Note: This introduction will save you more

time than it takes to read it!

Identifying Parts

To help you identify the small parts used in assem-

bly, we have included a PART IDENTIFICATION

CHART located in the center of this manual. Place

the chart on the floor and use it to quickly identify dif-

ferent parts as you open the packages for each step.

Note: Some small parts may have been pre-

attached. If a part is not in the parts bag, check to

see if it has been pre-attached.

Orienting Parts

As you assemble this product, be sure that all parts

are oriented as shown in the drawings.

Tightening Parts

Tighten all parts as you assemble them, unless

instructed to do otherwise.

Required Tools

Assembly requires the following tools (not included):

¥ Two (2) adjustable wrenches

¥ One (1) standard screwdriver

¥ One (1) phillips screwdriver

¥ One (1) rubber mallet

¥ Lubricant, such as grease or petroleum jelly,

and soapy water

¥ Tape, such as clear tape or masking tape

Assembly will be more convenient if you have a

socket set, a set of open-end or closed-end wrenches

or a set of ratchet wrenches.

Giving Yourself a Good Start

Before you begin the assembly process, take the

time to complete the steps outlined here.

Clearing the Workspace

Clear a workspace that is large enough to hold all

parts and allow you to walk all the way around the

assembled equipment.

Unpacking the Box

To make the assembly process as smooth as possi-

ble, we have broken it into separate stages. All parts

used in each stage are found in individual packages

in the shipping box. Place all parts in a cleared area

and remove the packing materials. Do not dispose of

the packing materials until assembly is completed.

Important: Wait until you begin each assembly

stage to open the parts bag labeled for that

assembly stage.

Assembly

Making Things Easier for Yourself

Everything in this manual is designed to ensure

that the weight system can be assembled suc-

cessfully by anyone. However, it is important to

recognize that the weight system is a sophisti-

cated product with many small parts. The

assembly process will take timeÑpossibly sev-

eral hours. By setting aside plenty of time, and

by deciding to make the task enjoyable, assem-

bly will go smoothly. You may want to complete

the process over a couple of evenings.

The Four Stages of the Assembly Process

Frame Assembly

You will begin by assembling the base and the

upright frames that serve as the skeleton of the

equipment.

Arm Assembly

Completes the press and butterfly arms that you

operate while you are exercising.

Cable Assembly

Completes the cables and pulleys that connect the

moving arms with each other and with the weight

mechanism.

Seat Assembly

Completes the seats and backrests that support

your body while you are exercising.

1. Before beginning assembly, make sure you have

read and understood the information on page 5.

Open the parts bag labeled ÒFRAME ASSEMBLY.Ó

Press a 2Ó Square Outer Cap (51) onto each end of

the Stabilizer (5).

Insert two 5/16Ó x 2 3/4Ó Carriage Bolts (14) up

through the Stabilizer (5) and place it flat on the floor.

2. Press a 2Ó Square Inner Cap (21) into the end of the

Base (8).

Insert two 5/16Ó x 2 1/2Ó Carriage Bolts (52) up

through the Base (8).

Place the Base (8) on the floor with the holes in the

mounting bracket over the Carriage Bolts (14) in the

Stabilizer (5).

Frame Assembly

Bracket

3. Press a 1Ó x 2Ó Inner Cap (11) into the top of the Rear

Upright (18).

Slide the Rear Upright (18) onto the 5/16Ó x 2 3/4Ó

Carriage Bolts (14) in the Stabilizer (5). Hand tighten

a 5/16Ó Nylon Locknut (53) onto each Carriage Bolt.

Make sure the Rear Upright (18) is oriented as

shown. The wide side of the bracket on the lower

end must be on the side shown.

Slide the Front Upright (42) onto the 5/16Ó x 2 1/2Ó

Carriage Bolts (52) in the Base (8). Hand tighten a

5/16Ó Nylon Locknut (53) onto each Carriage Bolt.

Do not tighten the Nylon Locknuts yet.

Wide

Side of

the

Bracket

18 42

4. Press a 2Ó Square Inner Cap (21) into each end of

the crossbar on the Top Frame (1).

Slide two 5/16Ó Flat Washers (56) onto two 5/16Ó x

2 3/4Ó Bolts (67).

Place the Top Frame (1) on top of the Front Upright

(42) and align the indicated holes with the holes in

the bracket on the Front Upright.

Insert the 5/16Ó x 2 3/4Ó Bolts (67) through the Top

Frame (1) and the bracket on the Front Upright (42).

Hand tighten a 5/16Ó Nylon Locknut (53) onto each

Bolt. Do not tighten the Nylon Locknuts yet.

56 21

Bracket

Crossbar

5. Slide two 5/16Ó Flat Washers (56) onto two 5/16Ó x

1 3/4Ó Bolts (58).

Align the holes in the bracket on the Top Frame (1)

with the holes in the Rear Upright (18). Insert the

5/16Ó x 1 3/4Ó Bolts (58) and hand tighten two 5/16Ó

Nylon Locknuts (53) onto them.

Tighten all of the Nylon Locknuts used in steps 3

to 5.

58 1

Knobs

ÒUÓ-bracket

6. Note: Make sure that you do not cut the wires

while cutting the tie that is holding the Weight

Mechanism (26).

Cut the Weight Mechanism (26) away from the Front

Upright (42). Carefully lower the Mechanism onto the

Base (8), positioning the ÒUÓ-bracket as shown.

7. Snap the Shocks (16) onto the indicated knobs on the

Front Upright (42) and the Weight Mechanism (26).

10. Press a 1 1/2Ó Square Inner Cap (33) into the end of

the Seat Frame (36).

Insert two 5/16Ó x 2 3/4Ó Bolts (67) through the

Support Plate (27) and the indicated holes in the

Front Upright (42). Place the mounting bracket on the

Seat Frame (36) over the two Bolts. Tighten a 5/16Ó

Nylon Locknut (53) onto each Bolt. Make sure the

Support Plate (27) is oriented as shown.

Press the Angle Cap (62) onto the end of the rod on

the Support Plate (27). Make sure that the Angle

Cap is angled as shown in the inset drawing.

Rod 42

Bracket

27 53

11. Open the parts bag labeled ÒARM ASSEMBLY.Ó

Press a Plastic Bushing (7) onto each welded tube on

the Press Frame (12).

Lubricate the 3/8Ó x 8Ó Bolt (59). Attach the Press

Frame (12) to the Base (8) with the Bolt and a 3/8Ó

Nylon Locknut (57).

Arm Assembly

59 Lubricate

Welded Tubes

9. Feed both Wire Ties (23) into the Wire Tie Blocks (82)

that are pre-assembled to the Base (8). Carefully

position the wire bundle over the Wire Tie Blocks and

secure the wires to the Base with the Wire Ties.

Note: The other end of the wire bundle will be

attached to a shroud in a later step. Make sure that

some slack is left between the wires and the

Weight Mechanism (26, not shown) for this pur-

pose.

82 8

Wires

8. Attach the indicated end of the Console Cord (83) to

the indicated end of the wire bundle. Make sure that

the Console Cord is attached exactly as shown.

Wires

Lubricate

Bracket

345

Axle

13. Identify the Right Butterfly Arm (48) and the Left

Butterfly Arm (47). Note the position of the welded

bracket on each Arm. Arm identification is very

important for this step.

Lubricate both axles on the Top Frame (1). Slide the

Right Butterfly Arm (48) onto the right axle. Note: Be

careful not to confuse the Right and Left Butterfly

Arms. Make sure the upper end of the Right

Butterfly Arm is behind the indicated bracket on

the Top Frame.

Tap two 1Ó Retainers (4) and a 1Ó Round Cover Cap

(3) onto the Right Axle. To do this, place the two

retainers on top of the Cover Cap. Make sure the

teeth on the Retainers (4) bend towards the Cover

Cap (3), as shown in the inset drawing. Tap on the

Cover Cap with a rubber mallet.

Attach the Left Butterfly Arm (47) in the same man-

ner. Press a 2Ó Square Inner Cap (21) into the lower

end of each Butterfly Arm (47, 48).

Lubricate the lower end of each Butterfly Arm (47, 48)

with soapy water and slide a Foam Pad (45) onto

each Arm.

14. Press a 1 1/2Ó Square Inner Cap (33) into the Leg

Lever (29).

Lubricate a 5/16Ó x 2 1/2Ó Bolt (22). Attach the Leg

Lever (29) to the Seat Frame (36) with the Bolt and a

5/16Ó Nylon Jamnut (91). Do not overtighten the

Nylon Jamnut. The Leg Lever should pivot freely.

Attach the 3/8Ó x 2 1/4Ó Eyebolt (44) into the indicated

hole in the Leg Lever (29) with a 3/8Ó Flat Washer

(55) and a 3/8Ó Nylon Locknut (57).

22 Lubricate

Left

Right

12. Note: In the following steps, some parts are not

shown for clarity.

Press a 2Ó Square Inner Cap (21) into the top of a

Press Arm (46). Press a 1Ó Round Inner Cap (49) into

the indicated hole in the Press Arm (46).

Attach the Press Arm (46) to the Press Frame (12)

with two 5/16Ó x 2 3/4Ó Bolts (67) and two 5/16Ó Nylon

Locknuts (53).

Attach the other Press Arm (46) in the same way.

Cable Assembly

15. Open the parts bag labeled ÒCABLE ASSEMBLY

AND PULLEYS.Ó For Cable identification and rout-

ing during steps 15Ð30, refer to the Cable

Diagram and Cable ID Chart on page 19.

Identify the High Cable (2). It is approximately 163

1/2Ó long. It is the shortest cable and it has a ball on

each end. Wrap the end with the small ball around a

3 1/2Ó Pulley (35) in the direction shown.

Attach the Pulley (35) to the Top Frame (1) with a

3/8Ó x 3 1/2Ó Bolt (54), a 3/8Ó Flat Washer (55) and a

3/8Ó Nylon Jamnut (63).

Make sure the High Cable (2) is between the

Pulley (35) and the welded hook on the Top Frame

(1).

Hook

16. Wrap the High Cable (2) around a ÒVÓ-Pulley (6) in

the direction shown.

Attach the ÒVÓ-Pulley (6) and a Long Cable Trap (50)

to the indicated bracket with a 3/8Ó x 2 1/4Ó Bolt (65)

and a 3/8Ó Nylon Locknut (57). Make sure the Long

Cable Trap is positioned as shown, so it will hold

the Cable in place.

16 Welded

Bracket

17. Wrap the High Cable (2) around a ÒVÓ-Pulley (6) in

the direction shown.

Attach the ÒVÓ-Pulley (6) and a Long Cable Trap (50)

to the Left Butterfly Arm (47) with a 3/8Ó x 2 1/2Ó Bolt

(96) and a 3/8Ó Nylon Locknut (57).

Make sure the Long Cable Trap (50) is positioned

as shown. It may be helpful to take the Butterfly

Arm (47) through one full range of motion to

ensure that the Cable Trap does not rub on the

cable.

Route the High Cable (2) under the Top Frame (1)

between the ÒVÓ-Pulley (6) and the crossbar.

Crossbar

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Weider Heim-Fitnessstudio Handbücher

Weider

Weider 8950 Bedienungs- und Wartungshandbuch

Weider

Weider WESY39523 Bedienungsanleitung

Weider

Weider PRO 260 Bedienungsanleitung

Weider

Weider PLATINUM 831.153970 Bedienungsanleitung

Weider

Weider 831.150721 Bedienungsanleitung

Weider

Weider 8630 Training Bedienungsanleitung

Weider

Weider Pro 400 Bedienungsanleitung

Weider

Weider Easy Compact 90 Einrichtungshandbuch

Weider

Weider Pro 9625 Bedienungsanleitung

Weider

Weider WEEVSY87210 Bedienungsanleitung

Weider

Weider 170 Tc Bench Kurzanleitung

Weider

Weider D130 Bedienungsanleitung

Weider

Weider PRO 9645 Bedienungsanleitung

Weider

Weider WEBE37330 Bedienungsanleitung

Weider

Weider 325 Bench Bedienungsanleitung

Weider

Weider WESY85104 Bedienungsanleitung

Weider

Weider WESY78732 Bedienungsanleitung

Weider

Weider WEBE34100 Bedienungsanleitung

Weider

Weider WEBE0332.0 Bedienungsanleitung

Weider

Weider 340 Classic Bench Bedienungsanleitung

Weider

Weider Flex 8960 Bedienungsanleitung

Weider

Weider Gold MEDALLION M4744 Bedienungsanleitung

Weider

Weider 9000 Bench Bedienungs- und Wartungshandbuch

Weider

Weider Pro 2000 Kurzanleitung

Beliebte Heim-Fitnessstudio Handbücher anderer Marken

Horizon Fitness

Horizon Fitness OXFORD 6 Bedienungsanleitung

Energetics

Energetics Multi Trainer 5.1 Bedienungsanleitung

Matrix

Matrix MG-PL Series Bedienungsanleitung

Reebok

Reebok Tbr2i Bedienungs- und Wartungshandbuch

Pure Fitness

Pure Fitness 8526HE Bedienungsanleitung

Bowflex

Bowflex Sport 001-6961 Bedienungsanleitung

NordicTrack

NordicTrack E8200 Competition Bench Kurzanleitung

Body Solid

Body Solid GHYP-345 Bedienungsanleitung

Evo

Evo TAHOE 5105 Bedienungsanleitung

ParaBody

ParaBody 40 Bedienungsanleitung

JLL

JLL Ventus Pro Air Power Bedienungsanleitung

Trojan

Trojan Colorado 370 Bedienungsanleitung

Octane Fitness

Octane Fitness xRide xR650 Bedienungsanleitung

Precor

Precor Discovery Series Bedienungsanleitung

Insportline

Insportline RW600 Bedienungsanleitung

Stamina

Stamina 55-1532 Bedienungsanleitung

Tunturi

Tunturi R25 Bedienungsanleitung

CYBEX

CYBEX Jungle Gym 17000 Bedienungsanleitung