Weslo 78e 831.29522.0 Bedienungsanleitung

Model No. 831.29522.0

Serial No.

CAUTION

Read all precautions and instruc-

tions in this manual before using

this equipment. Save this manu-

al for future reference. Sears, Roebuck and Co., Hoffman Estates, IL 60179

TREADMILL EXERCISER

User’s Manual

• Assembly

• Operation

• Maintenance

• Part List and Drawing

Serial Number Decal

TABLE OF CONTENTS

IMPORTANT PRECAUTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

BEFORE YOU BEGIN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

ASSEMBLY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

OPERATION AND ADJUSTMENT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

HOW TO FOLD AND MOVE THE TREADMILL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

MAINTENANCE AND TROUBLESHOOTING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

CONDITIONING GUIDELINES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

ORDERING REPLACEMENT PARTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Back Cover

FULL 90 DAY WARRANTY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Back Cover

Note: A PART IDENTIFICATION CHART, an EXPLODED DRAWING, and a PART LIST are attached in the

center of this manual.

1. It is the responsibility of the owner to ensure

that all users of this treadmill are adequately

informed of all warnings and precautions.

2. Use the treadmill only as described.

3. Place the treadmill on a level surface, with at

least eight feet of clearance behind it and two

feet on each side. Do not place the treadmill

on any surface that blocks air openings. To

protect the floor or carpet from damage,

place a mat under the treadmill.

4. Keep the treadmill indoors, away from mois-

ture and dust. Do not put the treadmill in a

garage or covered patio, or near water.

5. Do not operate the treadmill where aerosol

products are used or where oxygen is being

administered.

6. Keep children under the age of 12 and pets

away from the treadmill at all times.

7. The treadmill should not be used by persons

weighing more than 250 pounds.

8. Never allow more than one person on the

treadmill at a time.

9. Wear appropriate exercise clothing when

using the treadmill. Do not wear loose cloth-

ing that could become caught in the tread-

mill. Athletic support clothes are recommend-

ed for both men and women. Always wear

athletic shoes. Never use the treadmill with

bare feet, wearing only stockings, or in san-

dals.

10. When connecting the power cord (see page 9),

plug the power cord into a surge suppressor

(not included) and plug the surge suppressor

into a grounded circuit capable of carrying 15

or more amps. No other appliance should be on

the same circuit. Do not use an extension cord.

11. Use only a single-outlet surge suppressor that

meets all of the specifications described on

page 9. To purchase a surge suppressor, see

your local Sears store or call 1-800-366-7278

and order part number 146148, or see your

local electronics store.

12. Failure to use a properly functioning surge

suppressor could result in damage to the con-

trol system of the treadmill. If the control sys-

tem is damaged, the walking belt may change

speed, accelerate, or stop unexpectedly,

which may result in a fall and serious injury.

13. Keep the power cord and the surge suppres-

sor away from heated surfaces.

14. Never move the walking belt while the power

is turned off. Do not operate the treadmill if

the power cord or plug is damaged, or if the

treadmill is not working properly. (See page

12 if the treadmill is not working properly.)

15. Never start the treadmill while you are stand-

ing on the walking belt. Always hold the

handrails while using the treadmill.

16. The treadmill is capable of high speeds.

Adjust the speed in small increments to

avoid sudden jumps in speed.

17. Never leave the treadmill unattended while it is

running. Always remove the key and unplug

the power cord when the treadmill is not in

use.

18. Do not attempt to raise, lower, or move the

treadmill until it is properly assembled. (See

ASSEMBLY on page 6, and HOW TO MOVE

THE TREADMILL on page 11.) You must be

able to safely lift 45 pounds (20 kg) in order

to raise, lower, or move the treadmill.

19. Do not change the incline of the treadmill by

placing objects under the treadmill.

20. When folding or moving the treadmill, make

sure that the storage latch is fully closed.

21. Inspect and properly tighten all parts of the

treadmill regularly.

WARNING: To reduce the risk of burns, fire, electric shock, or injury to persons, read

the following important precautions and information before operating the treadmill.

IMPORTANT PRECAUTIONS

22. Never drop or insert any object into any

opening.

23. DANGER: Always unplug the power

cord immediately after use, before cleaning

the treadmill, and before performing the

maintenance and adjustment procedures

described in this manual. Never remove the

motor hood unless instructed to do so by an

authorized service representative. Servicing

other than the procedures in this manual

should be performed by an authorized ser-

vice representative only.

24. This treadmill is intended for in-home use

only. Do not use this treadmill in any com-

mercial, rental, or institutional setting.

WARNING: Before beginning this or any exercise program, consult your physician.

This is especially important for persons over the age of 35 or persons with pre-existing health prob-

lems. Read all instructions before using. Sears assumes no responsibility for personal injury or

property damage sustained by or through the use of this product.

SAVE THESE INSTRUCTIONS

The decals shown here have been placed

on your treadmill. If a decal is missing or

illegible, please call toll-free 1-866-699-

3756 and order a free replacement decal.

Apply the decal in the location shown.

Note: The decals are not shown at actual

size.

BEFORE YOU BEGIN

Handrails

Console

Storage Latch

Key/Clip

Reset/Off

Circuit Breaker

Walking Belt

Foot Rails

Incline Leg

Incline Pin

Power Cord

FRONT

BACK

RIGHT SIDE

Rear Roller

Adjustment Bolts

Water Bottle Holder

(Bottle not included)

Accessory Tray

Upright

Thank you for selecting the WESLO®CADENCE 78e

treadmill. The CADENCE 78e treadmill combines

advanced technology with innovative design to let you

enjoy an excellent form of cardiovascular exercise in

the convenience and privacy of your home. And when

you’re not exercising, the unique CADENCE 78e

treadmill can be folded up, requiring less than half the

floor space of other treadmills.

For your benefit, read this manual carefully before

using the treadmill. If you have questions after read-

ing this manual, call 1-800-4-MY-HOME®(1-800-469-

4663). To help us assist you, please note the product

model number and serial number before calling. The

model number of the treadmill is 831.29522.0. The seri-

al number can be found on a decal attached to the

treadmill (see the front cover of this manual for the loca-

tion).

Before reading further, please review the drawing

below and familiarize yourself with the labeled parts.

ASSEMBLY

Assembly requires two persons. Set the treadmill in a cleared area and remove all packing materials. Do not

dispose of the packing materials until assembly is completed.

Note: The underside of the treadmill walking belt is coated with high-performance lubricant. During shipping, a

small amount of lubricant may be transferred to the top of the walking belt or the shipping carton. This is a nor-

mal condition and does not affect treadmill performance. If there is lubricant on top of the walking belt, simply

wipe off the lubricant with a soft cloth and a mild, non-abrasive cleaner.

Assembly requires the included allen wrenches and your own phillips screwdriver , wire

cutters , and needlenose pliers .

For help identifying the assembly hardware, see the PART IDENTIFICATION CHART attached in the cen-

ter of this manual. If a part is not in the parts bag, first check to see if it has been pre-assembled. If a part is

missing, call toll-free 1-866-699-3756.

2. With the help of a second person, carefully lower the

Uprights (46) to the floor. Make sure that the Base

Legs (21) do not fall out of the base of the Uprights.

Attach the Base Legs with the four Base Leg Screws

(62).

Attach the two Base Pads (63) to the base of the

Uprights (46) in the locations shown with the two 3/4”

Tek Screws (3).

With the help of another person, raise the Uprights (46)

to the vertical position.

1. Make sure that the power cord is unplugged.

With the help of another person, raise the Uprights (46)

to the vertical position. Insert one of the Base Legs (21)

into the treadmill as shown. (Note: It may be helpful to

tip the Uprights as you insert the Base Leg.) Make sure

that the Thin Base Pad (53) is under the Base Leg

and that the Wheel (68) is positioned as shown.

Insert the other Base Leg (not shown) in the same way.

3. If there is a plastic tie in the right Upright (46), remove

the plastic tie.

Hold one of the Handrails (59) near the right Upright (46)

as shown. Insert the Wire Harness (60) up through the

hole in the bottom of the Handrail and out of the round

hole in the side of the Handrail. If necessary, use

needlenose pliers to pull the Wire Harness out of the

hole. Be careful not to damage the Wire Harness.

Set the Handrail (59) on the upper end of the right

Upright (46). Tighten a Handrail Bolt (55) into the right

Handrail and the Upright as shown. Be careful not to

pinch the Wire Harness (60).

Attach the other Handrail (59) as described above. Note:

There are no wires on the left side.

60 59

Plastic Ties

4. Set the Console Base (52) on the Handrails (59). Thread

four 3/4” Screws (2) into the Handrails and the Console

Base. After you have started all four Screws, tighten the

Screws until they are snug; do not overtighten the

Screws. Note: It may be helpful to press down on the

top of the Console Base above the Handrails as you

tighten the Screws.

Insert the Wire Harness (60) through the two indicated

plastic ties on the Console Base (52) and up through the

hole in the Console Base as shown.

5. Hold the Console (65) near the Console Base (52).

Touch the right Handrail (59) to discharge any static.

Insert the Wire Harness (60) through the plastic tie

labeled C in the drawing at the right. Next, locate the

connector on the Wire Harness. Plug the Wire Harness

into the connector labeled A in the drawing at the right

and in the inset drawing. The connectors should slide

together easily and snap into place. If they do not,

turn the connector on the Wire Harness and try again. IF

THE CONNECTOR IS NOT INSERTED PROPERLY,

THE CONSOLE MAYBE DAMAGED WHEN THE

POWER IS TURNED ON.

Pull any slack in the Wire Harness (60) through the plas-

tic tie labeled C, and securely tighten the plastic tie

around the Wire Harness. Cut off the end of the plastic

tie.

59 52

Tie C

60 A

48 2

7. Attach the Storage Latch (48) to the left Upright (46)

with two 3/4” Screws (2).

8. Make sure that all parts used in assembly are properly tightened before you use the treadmill. Keep

the included allen wrench in a secure place. The allen wrench is used to adjust the walking belt (see page

13). To protect the floor or carpet, place a mat under the treadmill.

Screw

6. Set the Console (65) in the Console Base (52). Make sure

that no wires are pinched. Insert as much of the Wire

Harness (60) as possible down into the hole in the right

Handrail (59). Securely tighten the plastic tie nearest to

the right Handrail. Pull any excess Wire Harness

between the plastic ties tight and then tighten the other

plastic tie. Cut off the ends of the plastic ties.

Cover the Wire Harness (60) with the Wire Cover (11),

and route the Wire Harness out of the hole in the side of

the Wire Cover. Attach the Wire Cover to the back of the

Console Base (52) with two 3/4” Screws (2). Do not over-

tighten the Screws.

Attach the Console (65) to the Console Base (52) with

five 3/4” Screws (2) in the locations shown. Note: There

should not be a Screw in the hole indicated by the

arrow. Do not overtighten the Screws.

Ties

OPERATION AND ADJUSTMENT

THE PRE-LUBRICATED WALKING BELT

Your treadmill features a walking belt coated with high-

performance lubricant. IMPORTANT: Never apply sil-

icone spray or other substances to the walking

belt or the walking platform. Such substances will

deteriorate the walking belt and cause excessive

wear.

HOW TO PLUG IN THE POWER CORD

Your treadmill, like any other type of sophisticated

electronic equipment, can be seriously damaged by

sudden voltage changes in your home’s power.

Voltage surges, spikes, and noise interference can

result from weather conditions or from other appli-

ances being turned on or off. To decrease the pos-

sibility of your treadmill being damaged, always

use a surge suppressor with your treadmill (see

drawing 1 at the right). To purchase a surge sup-

pressor, see your local Sears store or call 1-800-

366-7278 and order part number 146148, or see

your local electronics store.

Use only a single-outlet surge suppressor that is

UL 1449 listed as a transient voltage surge sup-

pressor (TVSS). The surge suppressor must have

a UL suppressed voltage rating of 400 volts or less

and a minimum surge dissipation of 450 joules.

The surge suppressor must be electrically rated

for 120 volts AC and 15 amps. There must be a

monitoring light on the surge suppressor to indi-

cate whether it is functioning properly. Failure to

use a properly functioning surge suppressor could

result in damage to the control system of the

treadmill. If the control system is damaged, the

walking belt may change speed, accelerate, or

stop unexpectedly, which may result in a fall and

serious injury.

This product must be grounded. If it should mal-

function or break down, grounding provides a path of

least resistance for electric current to reduce the risk

of electric shock. This product is equipped with a cord

having an equipment-grounding conductor and a

grounding plug. Plug the power cord into a surge

suppressor, and plug the surge suppressor into an

appropriate outlet that is properly installed and

grounded in accordance with all local codes and

ordinances. Important: The treadmill is not com-

patible with GFCI-equipped outlets.

This product is for use on a nominal 120-volt circuit,

and has a grounding plug that looks like the plug illus-

trated in drawing 1 below. A temporary adapter that

looks like the adapter illustrated in drawing 2 may be

used to connect the surge suppressor to a 2-pole

receptacle as shown in drawing 2 if a properly

grounded outlet is not available.

The temporary adapter should be used only until a

properly grounded outlet (drawing 1) can be installed

by a qualified electrician.

The green-colored rigid ear, lug, or the like extending

from the adapter must be connected to a permanent

ground such as a properly grounded outlet box cover.

Whenever the adapter is used it must be held in place

by a metal screw. Some 2-pole receptacle outlet

box covers are not grounded. Contact a qualified

electrician to determine if the outlet box cover is

grounded before using an adapter.

DANGER: Improper connection

of the equipment-grounding conductor can

result in an increased risk of electric shock.

Check with a qualified electrician or service-

man if you are in doubt as to whether the

product is properly grounded. Do not modify

the plug provided with the product—if it will

not fit the outlet, have a proper outlet

installed by a qualified electrician.

Grounded Outlet Box

Grounding Plug

Surge Suppressor

Grounding Pin

Adapter

Lug

Metal Screw

Grounded Outlet

Grounding Pin

STEP-BY-STEP CONSOLE OPERATION

Before operating the console, make sure that the

power cord is properly plugged in (see page 9).

Next, step onto

the foot rails of

the treadmill.

Find the clip

attached to the

key, and slide

the clip onto the

waistband of

your clothes.

Then, insert the key fully into the console. Test the

clip by carefully taking a few steps backward until

the key is pulled from the console. If the key is not

pulled from the console, adjust the position of the

clip as needed. Note: To prevent damage to the

walking platform, always wear clean shoes when

using the treadmill.

Follow the steps below to operate the console.

Insert the key fully into the console.

When the key is inserted, the display will light.

Note: If there is a sheet of clear plastic on the

face of the console, remove the plastic.

Adjust the speed of the walking belt.

To start the walking belt, press the Digital Speed

increase button. The walking belt will begin to

move at 1 mph. As you exercise, change the

speed of the walking belt as desired by pressing

the Digital Speed buttons. Note: It may take a

moment for the walking belt to reach the selected

speed setting.

To stop the walking belt, press the Stop button.

Follow your progress with the display.

As you exer-

cise, the dis-

play will

show the

elapsed

time, the

speed of the

walking belt,

the approximate number of calories that you have

burned, and the distance that you have walked or

run during your workout.

Note: The console can display distance and

speed in either miles or kilometers. To change the

unit of measurement, first hold down the Stop but-

ton while inserting the key into the console. An

“E,” for English miles, or an “M,” for metric kilome-

ters, will appear in the display. Press the Digital

Speed increase button to change the unit of mea-

surement. Then, press the Stop button.

When you are finished exercising, remove the

key from the console.

After removing the key, unplug the power cord.

Make sure to keep the key in a secure place.

Note: The first time the treadmill is used, observe

the alignment of the walking belt, and align the

walking belt if necessary (see page 13).

HOW TO CHANGE THE INCLINE

To vary the intensity of your exercise, the incline of the

treadmill can be changed. There are four incline lev-

els. Before changing the incline, remove the key

and unplug the power cord. Next, fold the treadmill

to the storage position (see HOW TO FOLD THE

TREADMILL FOR STORAGE on page 11).

To change the incline, first remove the incline pin from

one of the incline legs. Adjust the incline leg to the

desired height, and fully reinsert the incline pin. Make

sure that the incline pin is in the “locked” position

shown in the inset drawing. Adjust the other incline leg

in the same way. Make sure that both incline pins

are inserted from the direction shown.

CAUTION: Before using the treadmill, make sure

that both incline legs are at the same height. Do

not use the treadmill with the incline pins

removed. After you have adjusted the incline legs,

lower the treadmill (see HOW TO LOWER THE

TREADMILL FOR USE on page 11).

Clip

Key

Incline

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Weslo Tretmühle Handbücher

Weslo

Weslo Cadence 8.0a Treadmill Bedienungsanleitung

Weslo

Weslo Lyne 3500 Treadmill Bedienungsanleitung

Weslo

Weslo Cadence 2050 Bedienungsanleitung

Weslo

Weslo Cadence Sl 20 Bedienungsanleitung

Weslo

Weslo Cadence M6 Elliptical Benutzerhandbuch

Weslo

Weslo Cadence 900 Treadmill Bedienungsanleitung

Weslo

Weslo Compact XS WETL20708.0 Bedienungsanleitung

Weslo

Weslo Cadence 3260 Bedienungsanleitung

Weslo

Weslo WETL91070 Bedienungsanleitung

Weslo

Weslo WLTL29010 Bedienungsanleitung

Weslo

Weslo WLTL48410 Bedienungsanleitung

Weslo

Weslo Cadence 215s Treadmill Bedienungsanleitung

Weslo

Weslo Cadence 1050 Bedienungsanleitung

Weslo

Weslo WLTL25320 Bedienungsanleitung

Weslo

Weslo Cadence R 7.2 Treadmill Bedienungsanleitung

Weslo

Weslo Cadence 200 Treadmill Benutzerhandbuch

Weslo

Weslo Cadence 85 Kurzanleitung

Weslo

Weslo Cadence E-20 Treadmill Bedienungsanleitung

Weslo

Weslo Cadence A60 Treadmill Bedienungsanleitung

Weslo

Weslo Cadence 630 Bedienungs- und Wartungshandbuch

Weslo

Weslo Cadence C6 Treadmill Benutzerhandbuch

Weslo

Weslo Cadence R20 Treadmill Bedienungsanleitung

Weslo

Weslo CADENCE TS300 Bedienungsanleitung

Weslo

Weslo Easy compact 2 treadmill Systemhandbuch

Beliebte Tretmühle Handbücher anderer Marken

Treadly

Treadly TREADLY 2 Bedienungsanleitung

HEALTH ONE

HEALTH ONE Walk Ro Bedienungsanleitung

NordicTrack

NordicTrack T7.5 S Bedienungsanleitung

Gold's Gym

Gold's Gym ADVANTAGE GGTL12920 Bedienungsanleitung

Merax

Merax MS282992 Bedienungsanleitung

FYTTER

FYTTER RU-2SX Bedienungsanleitung

Precor

Precor 903 Bedienungsanleitung

FitLogic

FitLogic freewill d225 Bedienungsanleitung

HOP-SPORT

HOP-SPORT ESTIMA HS-3200LB Bedienungsanleitung

Horizon Fitness

Horizon Fitness Adventure 5 Plus Bedienungsanleitung

Stamia

Stamia InMotion II Bedienungsanleitung

Smooth Fitness

Smooth Fitness EVO 3i Bedienungsanleitung

NordicTrack

NordicTrack NETL81810.0 Bedienungsanleitung

Schwinn

Schwinn 830/Journey 8.0 Bedienungsanleitung

Keys Fitness

Keys Fitness HealthTrainer HT-740T Bedienungsanleitung

Spirit

Spirit XT8 Bedienungsanleitung

NordicTrack

NordicTrack T 14.0 Treadmill Bedienungsanleitung

Master

Master F22 Bedienungsanleitung