Weslo Cadence 1000 Fm Bedienungsanleitung

USER'S MANUAL

Serial

Number

Decal

Model No. WETL28805.1

Serial No.

CAUTION

Read all precautions and in-

structions in this manual before

using this equipment. Save this

manual for future reference.

QUESTIONS?

As a manufacturer, we are com-

mitted to providing complete

customer satisfaction. If you

have questions, or if there are

missing or damaged parts,

please call:

or write:

ICON Health & Fitness, Ltd.

Customer Service Department

Unit 4

Revie Road Industrial Estate

Revie Road

Beeston

Leeds, LS118JG

email: [email protected]

08457 089 009

TABLE OF CONTENTS

IMPORTANT PRECAUTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3

BEFORE YOU BEGIN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5

ASSEMBLY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6

OPERATION AND ADJUSTMENT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10

HOW TO FOLD AND MOVE THE TREADMILL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16

TROUBLESHOOTING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17

CONDITIONING GUIDELINES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19

ORDERING REPLACEMENT PARTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Back Cover

Note: A PART IDENTIFICATION CHART, an EXPLODED DRAWING, and a PART LIST are attached in the

centre of this manual.

WESLO is a registered trademark of ICON IP, Inc.

1. It is the responsibility of the owner to ensure

that all users of this treadmill are adequately

informed of all warnings and precautions.

2. Use the treadmill only as described.

3. Keep the treadmill indoors, away from mois-

ture and dust. Do not put the treadmill in a

garage or covered patio, or near water.

4. Place the treadmill on a level surface, with at

least 2.5 m (8 ft.) of clearance behind it and

0.5 m (2 ft.) on each side. Do not place the

treadmill on a surface that blocks any air

openings. To protect the floor or carpet from

damage, place a mat under the treadmill.

5. Do not operate the treadmill where aerosol

products are used or where oxygen is being

administered.

6. Keep children under the age of 12 and pets

away from the treadmill at all times.

7. The treadmill should be used only by persons

weighing 115 kg (250 lbs.) or less.

8. Never allow more than one person on the

treadmill at a time.

9. Wear appropriate exercise clothes when

using the treadmill. Do not wear loose clothes

that could become caught in the treadmill.

Athletic support clothes are recommended for

both men and women.

Always wear athletic

shoes. Never use the treadmill with bare feet,

wearing only stockings, or in sandals.

10. Do not attempt to raise, lower, or move the

treadmill until it is properly assembled. (See

ASSEMBLY on page 6, and HOW TO FOLD

AND MOVE THE TREADMILL on page 16.)

You must be able to safely lift 20 kg (45 lbs) to

raise, lower, or move the treadmill.

11. When connecting the power cord (see page

10), plug the power cord into an earthed cir-

cuit. No other appliance should be on the

same circuit. When replacing the fuse, an

ASTA approved BS1362 type should be fitted

to the fuse carrier. A 13 amp fuse should be

used.

12. If an extension cord is needed, use only a 3-

conductor, 1mm2(14-gauge) cord that is no

longer than 1.5 m.

13. Keep the power cord away from heated

surfaces.

14. Do not change the incline of the treadmill by

placing objects under the treadmill.

15. Never move the walking belt whilst the power

is turned off. Do not operate the treadmill if

the power cord or plug is damaged, or if the

treadmill is not working properly. (See TROU-

BLESHOOTING on page 17 if the treadmill is

not working properly.)

16. Read, understand, and test the emergency

stop procedure before using the treadmill (see

OPERATION AND ADJUSTMENT on page 10).

17. Never start the treadmill whilst you are stand-

ing on the walking belt. Always hold the

handrails whilst using the treadmill.

18. The treadmill is capable of high speeds.

Adjust the speed in small increments to avoid

sudden jumps in speed.

19. The pulse sensor is not a medical device.

Various factors, including the user’s move-

ment, may affect the accuracy of heart rate

readings. The pulse sensor is intended only as

an exercise aid in determining heart rate

trends in general.

20. Never leave the treadmill unattended whilst it

is running. Always remove the key, unplug

the power cord, and move the on/off switch to

the off position when the treadmill is not in

use. (See the drawing on page 5 for the loca-

tion of the on/off switch.)

21. When folding or moving the treadmill, make

sure that the storage latch is fully closed.

WARNING: Toreduce the risk of burns, fire, electric shock, or injury to persons, read the

following important precautions and information before operating the treadmill.

IMPORTANT PRECAUTIONS

178425

Vertical Latch Warning Decal, Treadmill

The decal shown at the right has been placed on the

treadmill. If the decal is missing, or if it is not legible,

call the telephone number on the front cover of this

manual and order a free replacement decal. Apply

the decal in the location shown. Note: The decal may

not be shown at actual size.

22. Inspect and properly tighten all parts of the

treadmill regularly.

23. Never insert any object into any opening.

24. DANGER: Always unplug the power

cord immediately after use, before cleaning the

treadmill, and before performing the mainte-

nance and adjustment procedures described in

this manual. Never remove the motor hood un-

less instructed to do so by an authorised ser-

vice representative. Servicing other than the

procedures in this manual should be performed

byan authorised service representative only.

25. The treadmill is intended for in-home use

only. Do not use the treadmill in a commer-

cial, rental, or institutional setting.

WARNING: Before beginning this or any exercise program, consult your physician. This

is especially important for persons over the age of 35 or persons with pre-existing health problems.

Read all instructions before using. ICON assumes no responsibility for personal injury or property

damage sustained by or through the use of this product.

SAVE THESE INSTRUCTIONS

Thank you for selecting the new WESLO®CADENCE

1000 FM treadmill. The CADENCE 1000 FM treadmill

combines advanced technology with innovative design

to help you get the most from your exercise in the pri-

vacy of your home. And when you’re not exercising,

the unique CADENCE 1000 FM treadmill can be

folded up, requiring less than half the floor space of

other treadmills.

For your benefit, read this manual carefully before

using the treadmill.If you have questions after read-

ing this manual, please call our Customer Service

Department at 08457 089 009.To help us assist you,

please note the product model number and serial num-

ber before contacting us. The model number of the

treadmill is WETL28805.1. The serial number can be

found on a decal attached to the treadmill (see the

front cover of this manual for the location).

Before reading further, please familiarise yourself with

the parts that are labelled in the drawing below.

BEFORE YOU BEGIN

Handrail

Upright

Storage Latch

Key/Clip

Circuit Breaker

Walking Belt

Walking Platform

Foot Rail

RIGHT SIDE

Rear Roller

Adjustment Bolts

Console

Bookrack

Accessory Tray

On/Off Switch

BACK

ASSEMBLY

Assembly requires two persons. Set the treadmill in a cleared area and remove all packing materials. Do not

dispose of the packing materials until assembly is completed. Note: The underside of the treadmill walking belt is

coated with high-performance lubricant. During shipping, a small amount of lubricant may be transferred to the

top of the walking belt or the shipping carton. This is a normal condition and does not affect treadmill perfor-

mance. If there is lubricant on top of the walking belt, simply wipe off the lubricant with a soft cloth and a mild,

non-abrasive cleaner.

Assembly requires the included hex keys and your own phillips screwdriver , wire

cutters , and needlenose pliers .

For help identifying the assembly hardware, see the PART IDENTIFICATION CHART in the centre of this

manual.

1. Make sure that the power cord is unplugged.

Place the Base (79) in the position shown, with the indi-

cated small holes on top. Next, place the Wheels (63)

into the ends of the Base.

Attach the Wheels (63) to the Base (79) with 2” Bolts

(61) and Wheel Nuts (64). Make sure that the Wheel

Nuts are on the sides shown; do not overtighten the

Bolts; the Wheels should turn freely.

Attach the four Base Pads (73) to the Base (79) with four

1” Tek Screws (60) (three are shown).

2. Raise the Base (79) to a vertical position, and hold it

near the treadmill Frame (96) as shown. Make sure that

the Wheels (63) are in the indicated position.

Identify the Right Upright (104), which has a large round

hole in the indicated location. Feed the Wire Harness

(65) into the hole and out of the top of the Right Upright.

Make sure that there are two U-nuts (74) in the lower

end of the Right Upright (see drawing 2a). Hold the Right

Upright against the Base (79) as shown. Make sure that

the Right Upright is oriented so the pivot hole is in the

position shown. Hand tighten two 3” Bolts (58) with two

5/16” Star Washers (57) into the Base and the Right

Upright.

Attach the Left Upright (47) to the Base (79) in the same

way. Note: There is not a wire harness on the left side.

With the help of a second person, raise the Uprights (47,

104) to a vertical position.

Small Hole

Pivot

Holes

104

Round

Hole

5. Identify the Right Handrail (40), which has a pulse bar

bracket on its left side. Feed the Wire Harness (65) up

into the large bracket on the Right Handrail and out of

the large hole in the left side. (Note: It may be helpful to

use needlenose pliers to pull the Wire Harness out of the

hole.) Remove any nylon ties from the large bracket.

Insert the large bracket on the Right Handrail (40) into

the upper end of the Right Upright (104). Attach the Right

Handrail with two 1” Bolts (43), two 1/4” Washers (44),

two 1/4” Star Washers (45), a 4” Handrail Bolt (78), and a

5/16” Washer (106) as shown. Do not tighten the Bolts

yet.

See drawing 5a. Insert the included nylon tie through the

indicated hole in the Right Handrail (40). See drawing 5b.

Look into the Right Handrail and make sure that the Wire

Harness (65) is secured to the side shown. Then, tighten

the nylon tie and cut the excess off the end.

Attach the Left Handrail (not shown) in the same way.

Note: You may need to tip the Left Handrail to one side

as you insert the bracket. There is not a wire harness in

the left Upright (not shown).

3. Hold an Upright Spacer (59) against one side of the

Frame (96) as shown. Insert a 4” Frame Bolt (54) into the

indicated hole in the Upright Spacer and the Frame.

Next, tighten a 3/4” Tek Screw (9) into the Upright

Spacer and the Frame. Then, remove the 4” Frame Bolt.

Repeat this procedure on the other side of the Frame.

Have a second person lift the front end of the Frame

(96). Insert a 4” Frame Bolt (54) with a 3/8” Washer (12)

and a 3/8” Star Washer (55) into the Right Upright (104)

and the right Upright Spacer (59), and tighten the Frame

Bolt into the Frame. Do not overtighten the Frame

Bolt. Repeat this procedure on the left side of the Frame.

5512

Hole

104

43 44

104

106

Large

Hole

Large Bracket

Pulse Bar Bracket

5a 5b

Tie Tie

4. Attach the Latch Housing (46) to the Left Upright (47) with

two 3/4” Screws (38). Make sure that the large hole in

the Latch Housing is on the side shown.

Large Hole

Tie

8. Insert the Wire Harness (65) through the indicated nylon tie

on the Console Base (67). Next, touch the Right Handrail

(40) to discharge any static. See drawing 8a. Insert the

connector on the end of the Wire Harness into the red

socket beneath the Console (69). The connector should

slide easily into the socket and snap into place. If the

connector does not slide easily and snap into place, turn it

and then insert it. IF THE CONNECTOR IS NOT IN-

SERTED PROPERLY, THE CONSOLE MAY BE DAM-

AGED WHEN THE POWER IS TURNED ON.

Identify the 3/4” Screws (38). Attach the Console Base

(67) to the Right Handrail (40) and the Left Handrail (not

shown) with six 3/4” Screws (only three Screws are

shown). Start all six Screws before tightening them; do

not overtighten the Screws.

Tighten the Pulse Bar Screws (37).

7. Set the console assembly onto the Left and Right

Handrails (13, 40). Be careful not to pinch the Wire

Harness (65). Tighten two Pulse Bar Screws (37), with

two #10 Star Washers (108), through the brackets on the

Handrails and into the Pulse Bar (39). Do not tighten

the Pulse Bar Screws yet.

108

Console Assembly 13

6. Attach the end of the ground wire to the small hole in the

side of the Right Handrail (40) with a Silver Ground

Screw (66).

Ground Wire

12.Make sure that all parts are properly tightened before

you use the treadmill. Note: Extra hardware may be in-

cluded. Keep the included hex keys in a secure place;

the large hex key is used to adjust the walking belt (see

page 18). To protect the floor or carpet, place a mat

under the treadmill.

10. Lower the Handrails (13, 40) until they are touching the

floor.

See drawing 10a. Position the Handrails (13, 40) so the

treadmill Frame (96) is centered between them.

Firmly tighten the four 3” Bolts (58) and the two 4”

Frame Bolts (54). Be careful not to overtighten the

Bolts.

40, 13

Top View

10a

11. Remove the knob from the pin. Make sure that the col-

lar and the spring are on the pin. Insert the pin into the

Latch Housing (46), and then tighten the knob back onto

the pin.

46 Pin

Spring

Knob

Collar

9. Press the Wire Harness (65) into the indicated track in

the Console Base (67). (Note: If there is a cylinder on the

Wire Harness that will not fit into the track, press as

much of the Wire Harness as possible into the track.)

Next, insert the excess Wire Harness into the large hole

in the side of the Right Handrail (40). Securely tighten

the nylon tie to prevent the Wire Harness from slip-

ping, and then cut off the end of the nylon tie.

Attach the Access Door (84) to the Console Base (67) with

the 3/4” Screw (38).

See step 5. Tighten, but do not overtighten, the 1”

Bolts (43) and the 4” Handrail Bolts (78).

Tie Track

THE PRE-LUBRICATED WALKING BELT

Your treadmill features a walking belt coated with high-performance lubricant. IMPORTANT: Never apply sili-

cone spray or other substances to the walking belt or the walking platform. Such substances will deterio-

rate the walking belt and cause excessive wear.

HOW TO PLUG IN THE POWER CORD

This product must be earthed. If it should malfunction or break

down, earthing provides a path of least resistance for electric cur-

rent to reduce the risk of electric shock. This product is equipped

with a power cord having an equipment-earthing conductor and an

earthing plug. Important: If the power cord is damaged, it must

be replaced with a manufacturer-recommended power cord.

See drawing 1. Plug the indicated end of the power cord into the

socket on the treadmill.

See drawing 2. Press the pins on the power cord into the metal clips

in the adapter as shown. Close the adapter cover over the end of the

power cord and tighten the screw in the adapter. Important: Make

sure that the adapter cover is secure and the screw has been

tightened before using the power cord.

See drawing 3. Plug the power cord into an appropriate outlet that is

properly installed and earthed in accordance with all local codes and

ordinances. Important: The treadmill is not compatible with

GFCI-equipped outlets.

DANGER: Improper connection of the equipment-earthing conductor can result in an in-

creased risk of electric shock. Check with a qualified electrician or serviceman if you are in doubt as

to whether the product is properly earthed. Do not modify the plug provided with the product—if it will

not fit the outlet, have a proper outlet installed by a qualified electrician.

FR/SP

Socket on treadmill

Metal

Clips

Pins

Screw

Adapter

Outlet

Adapter

Cover

OPERATION AND ADJUSTMENT

Andere Handbücher für Cadence 1000 Fm

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Weslo Tretmühle Handbücher

Weslo

Weslo Cadence 3100 Bedienungsanleitung

Weslo

Weslo WETL34709.0 Bedienungsanleitung

Weslo

Weslo CADENCE C44 Bedienungsanleitung

Weslo

Weslo Cadence 70 Treadmill Bedienungsanleitung

Weslo

Weslo Cadence CT 4.8 Bedienungsanleitung

Weslo

Weslo TREADMILL 831.297100 Bedienungsanleitung

Weslo

Weslo Cadence G25 Treadmill Bedienungsanleitung

Weslo

Weslo CROSSWALK 5.2T Bedienungsanleitung

Weslo

Weslo Cadence 16.0 Cwl Treadmill Bedienungsanleitung

Weslo

Weslo Cadence 85 Bedienungsanleitung

Weslo

Weslo WETL28131 Bedienungsanleitung

Weslo

Weslo Crosswalk G 3.2 Treadmill Benutzerhandbuch

Weslo

Weslo WLTL29508.0 Bedienungsanleitung

Weslo

Weslo Cadence A 40 Treadmill Bedienungsanleitung

Weslo

Weslo Cadence 700 Treadmill Benutzerhandbuch

Weslo

Weslo Crosswalk 5.2t Treadmill Benutzerhandbuch

Weslo

Weslo Cadence 630 Bedienungsanleitung

Weslo

Weslo Crosswalk 5.0t Treadmill Bedienungsanleitung

Weslo

Weslo Cadence 5.0 Treadmill Bedienungsanleitung

Weslo

Weslo Lyne 3500 Treadmill Einrichtungshandbuch

Weslo

Weslo CROSSWALK 5.2T Bedienungsanleitung

Weslo

Weslo CADENCE LX25 Bedienungsanleitung

Weslo

Weslo Cadence 860 Treadmill Bedienungsanleitung

Weslo

Weslo WETL91072 Cadence 910 Bedienungsanleitung

Beliebte Tretmühle Handbücher anderer Marken

Treadly

Treadly TREADLY 2 Bedienungsanleitung

HEALTH ONE

HEALTH ONE Walk Ro Bedienungsanleitung

NordicTrack

NordicTrack T7.5 S Bedienungsanleitung

Gold's Gym

Gold's Gym ADVANTAGE GGTL12920 Bedienungsanleitung

Merax

Merax MS282992 Bedienungsanleitung

FYTTER

FYTTER RU-2SX Bedienungsanleitung

Precor

Precor 903 Bedienungsanleitung

FitLogic

FitLogic freewill d225 Bedienungsanleitung

HOP-SPORT

HOP-SPORT ESTIMA HS-3200LB Bedienungsanleitung

Horizon Fitness

Horizon Fitness Adventure 5 Plus Bedienungsanleitung

Stamia

Stamia InMotion II Bedienungsanleitung

Smooth Fitness

Smooth Fitness EVO 3i Bedienungsanleitung

NordicTrack

NordicTrack NETL81810.0 Bedienungsanleitung

Schwinn

Schwinn 830/Journey 8.0 Bedienungsanleitung

Keys Fitness

Keys Fitness HealthTrainer HT-740T Bedienungsanleitung

Spirit

Spirit XT8 Bedienungsanleitung

NordicTrack

NordicTrack T 14.0 Treadmill Bedienungsanleitung

Master

Master F22 Bedienungsanleitung