Weslo Cadence 85 Bedienungsanleitung

USER'S MANUAL

Serial

Number

Decal

Model No. WETL26140C

Serial No.

CAUTION

Read all precautions and in-

structions in this manual before

using this equipment. Save this

manual for future reference.

Class HC Fitness Product

QUESTIONS?

As a manufacturer, we are com-

mitted to providing complete

customer satisfaction. If you

have questions, or if there are

missing or damaged parts,

please call:

or write:

ICON Health & Fitness, Ltd.

Customer Service Department

Unit 4

Revie Road Industrial Estate

Revie Road

Beeston

Leeds, LS118JG

email: [email protected]

08457 089 009

TABLE OF CONTENTS

IMPORTANT PRECAUTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3

BEFORE YOU BEGIN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5

ASSEMBLY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6

OPERATION AND ADJUSTMENT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9

HOW TO FOLD AND MOVE THE TREADMILL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14

TROUBLESHOOTING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16

CONDITIONING GUIDELINES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18

ORDERING REPLACEMENT PARTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Back Cover

Note: An EXPLODED DRAWING and a PART LIST are attached in the centre of this manual.

WESLO is a registered trademark of ICON IP, Inc.

1. It is the responsibility of the owner to ensure

that all users of this treadmill are adequately

informed of all warnings and precautions.

2. Use the treadmill only as described.

3. Keep the treadmill indoors, away from mois-

ture and dust. Do not put the treadmill in a

garage or covered patio, or near water.

4. Place the treadmill on a level surface, with at

least 2.5 m (8 ft.) of clearance behind it and

0.5 m (2 ft.) on each side. Do not place the

treadmill on a surface that blocks any air

openings. To protect the floor or carpet from

damage, place a mat under the treadmill.

5. Do not operate the treadmill where aerosol

products are used or where oxygen is being

administered.

6. Keep children under the age of 12 and pets

away from the treadmill at all times.

7. The treadmill should be used only by persons

weighing 113 kg (250 lbs.) or less.

8. Never allow more than one person on the

treadmill at a time.

9. Wear appropriate exercise clothes when

using the treadmill. Do not wear loose clothes

that could become caught in the treadmill.

Athletic support clothes are recommended for

both men and women.

Always wear athletic

shoes. Never use the treadmill with bare feet,

wearing only stockings, or in sandals.

10. Do not attempt to raise, lower, or move the

treadmill until it is properly assembled. (See

ASSEMBLY on page 6, and HOW TO FOLD

AND MOVE THE TREADMILL on page 14.)

You must be able to safely lift 20 kg (45 lbs) to

raise, lower, or move the treadmill.

11. When connecting the power cord (see page 9),

plug the power cord into an earthed circuit.

No other appliance should be on the same cir-

cuit. When replacing the fuse, an ASTA ap-

proved BS1362 type should be fitted to the

fuse carrier. A 13 amp fuse should be used.

12. If an extension cord is needed, use only a 3-

conductor, 1mm2(14-gauge) cord that is no

longer than 1.5 m.

13. Keep the power cord away from heated

surfaces.

14. Do not change the incline of the treadmill by

placing objects under the treadmill.

15. Never move the walking belt whilst the power

is turned off. Do not operate the treadmill if

the power cord or plug is damaged, or if the

treadmill is not working properly. (See BE-

FORE YOU BEGIN on page 5 if the treadmill is

not working properly.)

16. Never start the treadmill whilst you are stand-

ing on the walking belt. Always hold the

handrails whilst using the treadmill.

17. The treadmill is capable of high speeds.

Adjust the speed in small increments to avoid

sudden jumps in speed.

18. The pulse sensor is not a medical device.

Various factors, including your movement,

may affect the accuracy of heart rate readings.

The sensor is intended only as an exercise aid

in determining heart rate trends in general.

19. Never leave the treadmill unattended whilst it

is running. Always remove the key, unplug

the power cord, and move the on/off switch to

the off position when the treadmill is not in

use. (See the drawing on page 5 for the loca-

tion of the on/off switch.)

20. When folding or moving the treadmill, make

sure that the storage latch is fully closed.

WARNING: Toreduce the risk of burns, fire, electric shock, or injury to persons, read the

following important precautions and information before operating the treadmill.

IMPORTANT PRECAUTIONS

39%

The decal shown have been placed on the treadmill. If a decal is missing, or if it is not legible, please call

our Customer Service Department to order a free replacement decal (see the back cover of this manual).

Apply the decal in the location shown. Note: The decals may not be shown at actual size.

21. Inspect and properly tighten all parts of the

treadmill regularly.

22. Never insert any object into any opening.

23. DANGER: Always unplug the power

cord immediately after use, before cleaning the

treadmill, and before performing the mainte-

nance and adjustment procedures described in

this manual. Never remove the motor hood un-

less instructed to do so by an authorised ser-

vice representative. Servicing other than the

procedures in this manual should be performed

byan authorised service representative only.

24. The treadmill is intended for in-home use

only. Do not use the treadmill in a commer-

cial, rental, or institutional setting.

WARNING: Before beginning this or any exercise program, consult your physician. This

is especially important for persons over the age of 35 or persons with pre-existing health problems.

Read all instructions before using. ICON assumes no responsibility for personal injury or property

damage sustained by or through the use of this product.

SAVE THESE INSTRUCTIONS

Congratulations for selecting the new WESLO®

CADENCE 85 treadmill. The CADENCE 85 treadmill

combines advanced technology with innovative design

to help you get the most from your exercise, in the pri-

vacy of your home. And when you’re not exercising, the

unique CADENCE 85 treadmill can be folded up, re-

quiring less than half the floor space of other treadmills.

For your benefit, read this manual carefully before

using the treadmill.If you have questions after read-

ing this manual, please call our Customer Service

Department at 08457 089 009.To help us assist you,

please note the product model number and serial num-

ber before calling. The model number of the treadmill

is WETL26140C. The serial number can be found on a

decal attached to the treadmill (see the front cover of

this manual for the location).

Before reading further, please familiarise yourself with

the parts that are labelled in the drawing below.

BEFORE YOU BEGIN

Handrail

Upright

Storage Latch

Key/Clip

Circuit Breaker

Walking Belt

Walking Platform

Foot Rail

RIGHT SIDE

Rear Roller

Adjustment Bolts

Console

Bookrack

Accessory Tray

On/Off Switch

BACK

ASSEMBLY

Assembly requires two persons. Set the treadmill in a cleared area and remove all packing materials. Do not

dispose of the packing materials until assembly is completed. Note: The underside of the treadmill walking belt is

coated with high-performance lubricant. During shipping, a small amount of lubricant may be transferred to the

top of the walking belt or the shipping carton. This is a normal condition and does not affect treadmill perfor-

mance. If there is lubricant on top of the walking belt, simply wipe off the lubricant with a soft cloth and a mild,

non-abrasive cleaner.

Assembly requires the included hex keys and your own phillips screwdriver , wire cutters

and needlenose pliers .

For help identifying the assembly hardware, refer to the PART IDENTIFICATION CHART in the centre of

this manual. Note: The assembly hardware and other small parts are packaged in separate part bags. Do

not open the part bags until instructed to do so.

1. Make sure that the power cord is unplugged.

Place the Base (79) in the position shown, with the indi-

cated small holes on top (only one small hole is shown).

Place a Wheel (63) in each Wheel Housing (62), and

slide the Wheel Housings onto the ends of the Base that

have bolt holes.

Open part bag A. Attach the Wheels (63) to the Wheel

Housings (62) with 2 1/2” Bolts (61) and Wheel Nuts

(64). Make sure that the Wheel Nuts are on the sides

shown; do not overtighten the Bolts.

Slide the two Base Endcaps (75) onto the other ends of

the Base (79) (only one Base Endcap is shown). Attach

the four Base Pads (73) to the Base Endcaps and the

Wheel Housings (62) with four 1 1/4” Tek Screws (60).

2. Raise the Base (79) to a vertical position, and hold it

near the treadmill Frame (96) as shown. Make sure that

the Wheels (63) are in the indicated position.

Identify the Right Upright (104), which has a large round

hole in the indicated location. Feed the Wire Harness

(65) into the hole and out of the top of the Right Upright.

Make sure that there are two U-Nuts (74) in the lower

end of the Right Upright (see drawing 2a). Hold the Right

Upright against the Base (79) as shown. Make sure that

the Right Upright is oriented so the pivot hole is in the

position shown. Hand tighten two 3” Bolts (58) with two

5/16” Star Washers (57) into the bottom of the Base and

the lower end of the Right Upright.

Attach the Left Upright (47) to the Base (79) in the same

way. Note: There is not a wire harness on the left side.

With the help of a second person, raise the Uprights (47,

104) to a vertical position.

Small Hole

Bolt

Hole 64

Pivot

Holes

104

Round

Hole

5. Feed the Wire Harness (65) up into the bracket on one of

the Handrails (40) and out of the large hole in the left

side. (Note: It may be helpful to use needlenose pliers to

pull the Wire Harness out of the hole.) Remove any plas-

tic ties from the bracket.

Insert the bracket on the Handrail (40) into the upper end

of the Right Upright (104). Attach the Handrail with two 1”

Bolts (43), two 1/4” Washers (44), two 1/4” Star Washers

(45), a 4” Bolt (117), and a 5/16” Washer (122) as

shown. Do not tighten the Bolts yet.

See drawing 5a. Insert the included nylon tie through the

indicated hole in the Handrail (40).

See drawing 5b. Look into the Handrail (40) and make

sure that the Wire Harness (65) is secured to the side

shown. Tighten the nylon tie and cut the excess off the

end.

Attach the other Handrail (not shown) in the same way.

Note: You may need to tip the Handrail to one side as

you insert the bracket. There is not a wire harness in the

left Upright (not shown).

4. Attach the Latch Housing (46) to the Left Upright (47)

with two 3/4” Screws (38). Make sure that the large hole

in the Latch Housing is on the side shown.

Remove the Latch Knob (48) from the Latch Pin (52).

Make sure that the Latch Pin Collar (49) and the Spring

(50) are on the Latch Pin. Insert the Latch Pin into the

Storage Latch (46), and then tighten the Latch Knob

back onto the Latch Pin.

Large Hole

3. Open part bag B. Hold an Upright Spacer (59) against

one side of the Frame (96) as shown. Insert a 3 1/2” Bolt

(54) into the indicated hole in the Upright Spacer and the

Frame. Next, tighten a Crossbar Screw (37) into the

Upright Spacer and the Frame. Remove the 3 1/2” Bolt.

Repeat on the other side of the Frame.

Have a second person lift the front end of the Frame

(96). Insert a 3 1/2” Bolt (54) with a 3/8” Star Washer (55)

into the Right Upright (104) and the right Upright Spacer

(59), and tighten the Bolt into the Frame. Do not over-

tighten the Bolt. Repeat on the left side of the Frame.

Hole

104

43 44

104

117

122

Large

Hole

Bracket

5a 5b

Tie Tie

9. Make sure that all parts are properly tightened before you use the treadmill. Note: Extra hardware may

be included. Keep the included hex keys in a secure place. The large hex key is used to adjust the walking

belt (see page 17). To protect the floor or carpet, place a mat under the treadmill.

8. Press the Wire Harness (65) into the recessed track on

the back of the Console Base (67). Note: There may be a

cylinder on the Wire Harness preventing it from being in-

serted into the track. Press as much Wire as possible

into the track.

Insert the excess Wire Harness (65) into the large hole in

the side of the right Handrail (40). Securely tighten the

nylon tie to prevent the Wire Harness from slipping.

Then, cut off the end of the nylon tie.

Attach the Access Door (84) to the Console Base (67) with

the 1/2” Screw (5).

Tighten, but do not overtighten, the bolts used in

step 5. With the help of a second person, lower the

uprights. Make sure the Frame (96) is centred be-

tween the Uprights (47, 104), and firmly tighten the

bolts used in steps 2.

Tie

7. Place the Console Base (67) on the right Handrail (40)

and the Left Handrail (not shown).

Insert the Wire Harness (65) through the indicated nylon tie

on the Console Base (67). Next, touch the right Handrail

(40) to discharge any static. See drawing 7a. Find the

connector on the end of the Wire Harness. Insert the con-

nector into the red socket beneath the Console (69). The

connector should slide easily into the socket and snap

into place. If the connector does not slide easily and snap

into place, turn the connector and then insert it. IF THE

CONNECTOR IS NOT INSERTED PROPERLY, THE

CONSOLE MAY BE DAMAGED WHEN THE POWER

IS TURNED ON.

Identify the 3/4” Screws (38); be careful not to confuse

the 3/4” Screws with the 1/2” Screw (5). Attach the

Console Base (67) to the right Handrail (40) and the Left

Handrail (not shown) with eight 3/4” Screws (only four

Screws are shown). Start all eight Screws before tight-

ening them. Do not overtighten the Screws.

Tighten the Crossbar Screws (37).

6. Attach the end of the ground wire to the small hole in the

side of the right Handrail (40) with a Silver Ground Screw

(66).

Open part bag C. Attach the Crossbar (39) to the right

Handrail (40) and the left Handrail (40) with two Crossbar

Screws (37). Do not tighten the Crossbar Screws yet.

Make sure that the rectangular hole in the Crossbar is on

the indicated side.

Ground Wire Hole

Track

THE PERFORMANT LUBETM WALKING BELT

Your treadmill features a walking belt coated with PERFORMANT LUBETM,ahigh-performance lubricant. IMPOR-

TANT: Never apply silicone spray or other substances to the walking belt or the walking platform. Such

substances will deteriorate the walking belt and cause excessive wear.

HOW TO PLUG IN THE POWER CORD

This product must be earthed. If it should malfunction or break

down, earthing provides a path of least resistance for electric cur-

rent to reduce the risk of electric shock. This product is equipped

with a power cord having an equipment-earthing conductor and an

earthing plug. Important: If the power cord is damaged, it must

be replaced with a manufacturer-recommended power cord.

See drawing 1. Plug the indicated end of the power cord into the

socket on the treadmill. Lift the tab on the ferrite box and clamp the

ferrite box around the power cord. Fasten the included plastic tie just

behind the ferrite box and cut off the excess plastic tie. The plastic tie

will prevent the ferrite box from sliding along the power cord.

See drawing 2. Press the pins on the power cord into the metal clips

in the Adaptor as shown. Close the Adaptor cover over the end of

the power cord and tighten the screw in the Adaptor. Important:

Make sure that the Adaptor cover is secure and the screw has

been tightened before using the power cord.

See drawing 3. Plug the power cord into an appropriate outlet that is

properly installed and earthed in accordance with all local codes and

ordinances. Important: The treadmill is not compatible with

GFCI-equipped outlets.

DANGER: Improper connection of the equipment-earthing conductor can result in an in-

creased risk of electric shock. Check with a qualified electrician or serviceman if you are in doubt as

to whether the product is properly earthed. Do not modify the plug provided with the product—if it will

not fit the outlet, have a proper outlet installed by a qualified electrician.

Socket on treadmill

Metal

Clips

Ferrite Box

Tab

Plastic Tie

Pins

Screw

Adaptor

Outlet

Adaptor

Cover

OPERATION AND ADJUSTMENT

FEATURES OF THE CONSOLE

The treadmill console offers a selection of features

designed to help you get the most from your workouts.

When the manual mode of the console is selected, the

speed and incline of the treadmill can be changed with

the touch of a button. As you exercise, the displays will

provide continuous exercise feedback. You can even

measure your heart rate using the built-in pulse sensor.

Two speed programs are also offered. Each program

automatically controls the speed of the treadmill as it

guides you through an effective workout.

HOW TO TURN ON THE POWER

Note: If there is a sheet of clear plastic on the face of

the console, remove the plastic.

Plug in the power cord (see page 9).

Locate the on/off

switch on the right side

of the treadmill near

the right upright. Make

sure that the switch is

in the “on” position.

Position

Key Clip

Andere Handbücher für Cadence 85

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Weslo Tretmühle Handbücher

Weslo

Weslo Cadence 950 Bedienungsanleitung

Weslo

Weslo WETL1214.0 Bedienungsanleitung

Weslo

Weslo Cadence 78e Treadmill Bedienungsanleitung

Weslo

Weslo Easy compact 2 treadmill Einrichtungshandbuch

Weslo

Weslo Lyne 3500 Treadmill Kurzanleitung

Weslo

Weslo Cadence 16.0 Cwl Treadmill Bedienungsanleitung

Weslo

Weslo Cadence M6 Elliptical Einrichtungshandbuch

Weslo

Weslo WCTL19809.0 Bedienungsanleitung

Weslo

Weslo Cadence 630 Benutzerhandbuch

Weslo

Weslo Cadence 200 Treadmill Bedienungsanleitung

Weslo

Weslo Cadence 830 Bedienungsanleitung

Weslo

Weslo Cadence 720 Kurzanleitung

Weslo

Weslo WLTL29310.0 Bedienungsanleitung

Weslo

Weslo Cadence S5 Treadmill Bedienungsanleitung

Weslo

Weslo Cadence 860 Treadmill Bedienungsanleitung

Weslo

Weslo Cadence 5.0a Treadmill Bedienungsanleitung

Weslo

Weslo Cadence SL20 WLTL33091 Bedienungsanleitung

Weslo

Weslo Cadence 900 Treadmill Benutzerhandbuch

Weslo

Weslo Cadence 915 Bedienungsanleitung

Weslo

Weslo Cadence Ex 18 Bedienungsanleitung

Weslo

Weslo CADENCE 850 WETL85061 Bedienungsanleitung

Weslo

Weslo Cadence 8.0a Treadmill Bedienungsanleitung

Weslo

Weslo Cadence 16.0 Cwl Treadmill Bedienungsanleitung

Weslo

Weslo compact SL Bedienungsanleitung

Beliebte Tretmühle Handbücher anderer Marken

Treadly

Treadly TREADLY 2 Bedienungsanleitung

HEALTH ONE

HEALTH ONE Walk Ro Bedienungsanleitung

NordicTrack

NordicTrack T7.5 S Bedienungsanleitung

Gold's Gym

Gold's Gym ADVANTAGE GGTL12920 Bedienungsanleitung

Merax

Merax MS282992 Bedienungsanleitung

FYTTER

FYTTER RU-2SX Bedienungsanleitung

Precor

Precor 903 Bedienungsanleitung

FitLogic

FitLogic freewill d225 Bedienungsanleitung

HOP-SPORT

HOP-SPORT ESTIMA HS-3200LB Bedienungsanleitung

Horizon Fitness

Horizon Fitness Adventure 5 Plus Bedienungsanleitung

Stamia

Stamia InMotion II Bedienungsanleitung

Smooth Fitness

Smooth Fitness EVO 3i Bedienungsanleitung

NordicTrack

NordicTrack NETL81810.0 Bedienungsanleitung

Schwinn

Schwinn 830/Journey 8.0 Bedienungsanleitung

Keys Fitness

Keys Fitness HealthTrainer HT-740T Bedienungsanleitung

Spirit

Spirit XT8 Bedienungsanleitung

NordicTrack

NordicTrack T 14.0 Treadmill Bedienungsanleitung

Master

Master F22 Bedienungsanleitung