Whispbar K333W Bedienungsanleitung
K333W
Fitting Kit
EN Fitting Instructions for Basic Carrier
x 1 x 4 x 4 x 4
x 4 x 4 x 4
Revision No: 7G 1
Fitting Kit K333W
MAX kgs (lbs)
W/P WHD
Hyundai
Terracan, 5dr SUV 01-05 EU 35 kgs (77 lbs) 35 kgs (77 lbs)
Terracan, 5dr SUV 01-05 CN 35 kgs (77 lbs) 35 kgs (77 lbs)
Terracan, 5dr SUV 01-07 ZA 35 kgs (77 lbs) 35 kgs (77 lbs)
Terracan, 5dr SUV Nov 01-Jun 07 NZ 35 kgs (77 lbs) 35 kgs (77 lbs)
Terracan, 5dr SUV Nov 01-Jun 07 AU 35 kgs (77 lbs) 35 kgs (77 lbs)
2
Fitting Kit EN
K333W
First Time Installation
●Remove parts from inside the package and
check. Contact your dealer if any parts are
missing or damaged.
●This kit fits type A, B, C and D.
●These instructions show type A crossbar
fitted. They also apply to type B, C and D.
●Use keys to remove covers.
3
Fitting Kit EN
K333W
●Use hex screwdriver to reverse adjusting
screw 10 turns.
●Press adjusting screw and pull crossbar
legs out. Refer to the crossbar instructions
for crossbar adjustment method.
●Ensure each end of the crossbar is
adjusted equally.
●Set bars to length (revert to rear of these
instructions).
●Please check the front of this manual for
information relating specifically to your
vehicle.
4
Fitting Kit EN
K333W
●Tighten adjusting screw to 5 Nm (3.7 ft lb)
hand tight.
●Remove plastic clamp block by gripping bar
leg with fingers and push firmly with
thumbs until clamp block drops out behind
leg.
●Select plastic internal block (from fitting kit)
and insert into foot.
5
Fitting Kit EN
K333W
●Fit rubber pads (supplied with fitting kit) to
foot. Pad may vary in shape to that shown.
●Make sure the pad fits into the holes
underneath the foot.
●Repeat for all legs.
Fitment
●Slide metal T-nuts into tracks on vehicle.
Two per track.
●Screw down the grubscrews into T-nuts
until it hits the track below (this will hold the
T-nuts in position).
●Do not over tighten.
●Place U-lock over grubscrew and T-nut.
Press down firmly.
6
Fitting Kit EN
K333W
●Top of U-lock to sit flush with top of track.
●Repeat for all four positions.
●Place crossbar foot over grubscrews.
●Tighten the plastic knob.
●Ensure the plastic knob is in the position
shown when fully tightened.
●Repeat for all four positions.
7
Fitting Kit EN
K333W
●Check crossbar is securely attached to the
vehicle.
●Use keys to fit and lock covers
CAUTION: Recheck all fasteners immediately after
a load is applied to the crossbars.
Regularly check screws are tight.
8
Fitting Kit EN
K333W
Maintenance
●Clean the car roof and surfaces of the
product that will be in contact with the car
roof.
●Follow the fitting instructions for fitting the
product to your vehicle. Make sure all steps
are carried out in order.
●Set crossbars a minimum distance of
700mm (27 1/2") apart where no other
distance is specified in the fitting
instructions. This is especially important
when carrying long loads.
●Check unit is securely attached whenever
you refit it to the vehicle. If the unit feels
loose, refer to the fitting instructions and
readjust.
●Some glass/panoramic roofs and radio
antennae may not be able to be used when
the product is fitted.
●Do not modify this product.
●Refer to the maximum permitted load
capacity specified in the fitting instructions.
Do not exceed the vehicle manufacturers
roof load rating if it is lower than the
maximum load capacity specified in the
fitting instructions.
●Loads should not overhang the sides of the
product and be evenly distributed with the
lowest possible centre of gravity.
●Long loads should be secured with non-
elastic straps to the front and rear of the
vehicle.
●Objects with pointed ends (e.g. ski poles)
should be carried with the pointed ends to
the rear of the vehicle.
●Remove all loose or removable objects
from the load prior to loading.
●Make sure all loads are securely fastened
with non-elastic straps. Check regularly
during longer journeys.
●A loaded roof rack system can alter the
performance of your vehicle. Be especially
aware of the effects of side winds,
changing of direction, and braking
performance. Avoid rapid acceleration and
deceleration. Drive carefully.
●Note that the total height of the vehicle
increases when upright loads are carried.
●Products should be locked during transport
if they have locks fitted.
9
Fitting Kit EN
K333W
●Check and replace worn out or defective
parts.
●Keep the product clean and maintained.
●Never drive into a car wash with the roof
rack system fitted.
●Lubricate locks and adjusting screws at
regular intervals.
●Remove the products from the vehicle
when not in use. Make sure all loose parts
are stored safely.
●Yakima Australia Pty Ltd
17 Hinkler Court
Brendale QLD 4500
AUSTRALIA
www.whispbar.com
www.whispbar.com.au
www.whispbar.co.nz
www.whispbar.co.uk
www.whispbar.co.za
www.whispbar.eu
www.whispbar.ca
10
Andere Handbücher für K333W
1
Inhaltsverzeichnis
Andere Whispbar Autozubehör Handbücher
Whispbar
Whispbar K449W Bedienungsanleitung
Whispbar
Whispbar K905W Bedienungsanleitung
Whispbar
Whispbar K828W Bedienungsanleitung
Whispbar
Whispbar K377W Bedienungs- und Installationshandbuch
Whispbar
Whispbar K604W Bedienungsanleitung
Whispbar
Whispbar K192W Bedienungsanleitung
Whispbar
Whispbar K484W Bedienungsanleitung
Whispbar
Whispbar S53W Bedienungsanleitung
Whispbar
Whispbar K464W Bedienungsanleitung
Whispbar
Whispbar K839W Bedienungsanleitung
Whispbar
Whispbar K916W Bedienungsanleitung
Whispbar
Whispbar K465W Bedienungsanleitung
Whispbar
Whispbar K001W Bedienungsanleitung
Whispbar
Whispbar K836W Bedienungsanleitung
Whispbar
Whispbar K324 Bedienungsanleitung
Whispbar
Whispbar K719 Bedienungsanleitung
Whispbar
Whispbar K584W Bedienungsanleitung
Whispbar
Whispbar K815W Bedienungsanleitung
Whispbar
Whispbar Q Series Bedienungsanleitung
Whispbar
Whispbar K800W Bedienungs- und Installationshandbuch
