Williams Sound Motiva PFM 360 Leitfaden

Models PFM 360, PFM 330, PFM 360 RCH & PFM 330 RCH

Transmitter Model PFM T36

Optional Receiver Models PFM R36, R33

MAN 146H

manual & user guide

Wireless FM Listening System

Motiva® Personal FM System

Models PFM 360, PFM 330, PFM 360 RCH & PFM 330 RCH

Manual and User Guide

System Overview 1

System Components 2

Safety Information 3

Recycling Instructions 3

Using the PFM T36 Transmitter 4

Using the PFM R33 / 36 Receiver 7

Belt Clip Installation 10

Channel Selection Chart 10

Battery Information 11

Limited Warranty 12

System Speciﬁcations 13

Fm Receiver, Model PFM R33 13

Fm Receiver, Model PFM R36 14

Fm Transmitter, Model PFM T36 15

System Overview

Thank you for purchasing a Motiva® Personal FM System from Williams Sound. Anyone needing audi-

tory assistance to overcome background noise, reverberation, or distance from a sound source can

beneﬁt from a Personal FM System.

Your PFM System has two principal parts: the Transmitter and the Receiver. Much like a miniature ra-

dio station, the Transmitter and microphone pick up the sounds you want to hear and broadcast them

over an FM radio signal. The receiver and earphone are used to pick up the broadcast up to 150 feet

away.

To avoid difﬁculties, please read through these instructions as you begin using the system. Then save

them for questions that arise as you continue to use your Williams Sound Personal FM System.

If you have problems with the PFM system, don’t hesitate to call us toll-free at 1-800-843-3544.

The speaker wears the belt-clip transmitter and a clip-on microphone. The speaker’s voice is broad-

cast as an FM radio signal over a distance of 150 feet. Listeners use the pocket receiver and

earphones or headphones to hear the speaker’s voice directly, with reduced background noise. An

optional neckloop telecoil coupler allows the system to be used with telecoil (T-switch) equipped hear-

ing aids.

System Components

Belt Clip Transmitter (PFM T36) with removable Belt Clip

Lavalier microphone (MIC 090)

Mini earphone (EAR 013)

Stereo auxiliary input cable (WCA 087)

System Carry Case (CCS 043)

Screwdriver (SDF 002)

Instructions (MAN 146)

PFM System 330 Only:

Personal FM Receiver (PFM R33)

(4) AA Alkaline non-rechargeable batteries (BAT 001)

PFM System 360 Only:

Personal FM Receiver (PFM R36)

Environmental Plug-mount Microphone (MIC 014)

(4) AA Alkaline non-rechargeable batteries (BAT 001)

PFM System 330 RCH Only:

Personal FM Receiver (PFM R33)

(4) AA NiMH rechargeable batteries (BAT 026)

Drop-in Charger (CHG 3502)

PFM System 360 RCH Only:

Personal FM Receiver (PFM R36)

Environmental Plug-mount Microphone (MIC 014)

(4) AA NiMH rechargeable batteries (BAT 026)

Drop-in Charger (CHG 3502)

T36 R36 R33

Safety Information

Hearing Safety

CAUTION!

This product is designed to amplify sounds to a high volume level which could potentially cause

hearing damage if used improperly. To protect your hearing and the hearing of others:

1. Turn the volume down before putting on the earphone or headphone, and then adjust the volume

to a comfortable level.

2. Set the volume level at the minimum setting that you need to hear.

3. If you experience feedback (a squealing or howling sound), reduce the volume setting and move

the microphone away from the earphone or headphone.

4. Do not allow children or other unauthorized persons to have access to this product.

Battery Safety

CAUTION!

This product may be supplied with alkaline batteries. Do not attempt to recharge alkaline batter-

ies, which may explode, release dangerous chemicals, cause burns, or other serious harm to the

user or product.

Medical Device Safety

CAUTION!

1. Before using this product with an implantable or other medical device, consult your physician or

the manufacturer of your implantable or other medical device.

2. If you have a pacemaker or other medical device, make sure that you are using this product

in accordance with safety guidelines established by your physician or the implantable device

manufacturer.

Recycling Instructions

Battery Safety and Disposal

Help Williams Sound protect the environment! Please take time to dispose of your equipment

properly. Please do NOT dispose of batteries in the household trash. Please take the batteries to

a retail or community collection point for recycling.

Product Recycling:

Please do NOT dispose of your Williams Sound equipment in the household trash. Please take

the equipment to an electronics recycling center or return the product to the factory for proper

disposal.

Using the PFM T36 Transmitter

IMPORTANT: If Alkaline (nonrechargeable) batteries are being installed, slide the battery selec-

tion switch in the battery compartment to the “Alkaline” position. See FIG 1 below. If installing

NiMH (or rechargeable) batteries, slide the battery selection switch to the “NiMH” position.

1. Install two (2) AA batteries. Note: rechargeable batteries must be charged before use.

See Battery Information on page 11.

2. Plug the microphone cord into the “Mic Jack” (

Mic Jack

Channel

Selector

Power On Indicator

Auxiliary

Input

Power On/Off/Mute

) on top of the transmitter.

Note: The microphone with 39 inch cord MUST be used with the Transmitter.

3. Optionally, plug in a desired audio source such as a CD or MP3 player using the “Auxiliary Input”

jack (WCA 087 stereo auxiliary input cable included). If the microphone and an auxiliary source are

used together, the audio will be mixed. If only the auxiliary source is desired, the microphone can

be muted. Do not remove the microphone from the “Mic Jack” as the microphone’s cable is also the

transmitting antenna!

4. Turn the unit on: press and hold the “ON/OFF/MUTE” button for three seconds. The “Power On”

indicator (

Mic Jack

Channel

Selector

Power On Indicator

Auxiliary

Input

Power On/Off/Mute

) should illuminate green.

5. Select the desired operating frequency. Use the “Channel Selector” knob to select any of the 16

available channels on 72-76 MHz. Refer to the channel selection chart (FIG 9, Page 10). Make

sure the receiver being used is operating on the same frequency as the T36 transmitter.

6. Place the transmitter in a pocket, or clip it onto a belt or waistband

(See “BELT CLIP INSTALLATION”, page 10).

–

Comp

CH Lock

- Gain + -

AUX

2:1

1:1

Mic Jack

Channel

Selector

Power On Indicator

Auxiliary

Input

Power On/Off/Mute

FIG. 1: Battery Selection Switch

FIG. 2: PFM T36 User Controls

7. Lapel clip microphones should be attached to a collar or lapel, as close to the speaker’s mouth

as practical. If using an optional headset microphone, position the mic as close to the side of the

mouth as possible without touching the mouth See FIG 3.

8. To mute the microphone, press the “ON/OFF/MUTE” button momentarily. The “ON/OFF/MUTE” but-

ton will ﬂash red. To unmute the microphone, press the “ON/OFF/MUTE” button momentarily again.

IMPORTANT: When the PFM T36 transmitter is not being used, remember to turn the unit OFF by

pressing and holding the “ON/OFF/MUTE” button for three seconds. The Power On indicator will not be

lit.

GAIN CONTROL

The gain control can be used to adjust the volume level on both the microphone and auxiliary input. To

adjust the volume level, open the battery door and locate the Gain Control (see FIG 4). Use the sup-

plied small screwdriver and rotate to increase “+” or decrease “-” the gain.

FIG. 3: Lapel Microphone Placement

–

Comp

CH Lock

- Gain + -

AUX

2:1

1:1

FIG. 4: Conﬁguration Controls

1 2 3 4

1. Gain Control 3. Compression Selector

2. Auxiliary Input Level 4. Channel Lock

Ye s Ye s No

AUXILIARY INPUT LEVEL

The auxiliary input level can be used to adjust the auxiliary input level only. To adjust, open the battery

door and locate the Auxiliary Input Level (see FIG 4). Use the supplied small screwdriver and rotate to

increase “+” or decrease “-” the input level.

Note: When using an auxiliary audio source, if the “Aux Input Level” is set too high, there can be in-

creased audio distortion and decreased battery life.

Note: Microphone cable serves as the transmitting antenna; therefore must remain plugged in during Aux

cable use.

COMPRESSION SELECTOR

By default, the PFM T36 compression is set to “Off” for normal operation, or “1:1” compression. For

hearing assistance applications, the compression selector can be set to “On” for “2:1” compression.

To change this setting, open the battery door and locate the Compression Selector (FIG 4). To turn on

compression, use the supplied small screwdriver and slide the “Comp” switch to the position marked

“2:1”. To turn off compression, slide the “Comp” switch to the position marked “1:1”.

CHANNEL LOCK

By default, the PFM T36 channels are unlocked to allow the user to change frequencies as needed. If

desired, channels can be locked to prevent users from changing the channels.

Note: The Channel Lock only locks the electronic frequency; it does not physically lock the channel selec-

tion knob.

To lock or unlock channels, open the battery door and locate the Channel Lock (FIG 4). To lock the cur-

rent channel while the unit is on, slide the “CH Lock” switch to the position marked (

–

Comp

CH Lock

- Gain + -

AUX

2:1

1:1

). To unlock the

channels, use the supplied small screwdriver and slide the “CH Lock” switch to the position marked (

–

Comp

CH Lock

- Gain + -

AUX

2:1

1:1

LOW BATTERY INDICATOR

The “Power On” indicator (see FIG 2) will ﬂash to indicate low battery.

BATTERY LIFE EXPECTANCY AFTER LOW BATTERY SIGNAL

Transmitter Receiver

Alkaline 90 min. Alkaline 60 min.

NiMH 15 min. NiMH 15 min.

Using the PFM R33 / R36 Receiver

IMPORTANT: If Alkaline (nonrechargeable) batteries are being installed, slide the battery selection

switch in the battery compartment to the “Alkaline” position. See FIG 5 below. If installing NiMH (or

rechargeable) batteries, slide the battery selection switch to the “NiMH” position.

1. Install two (2) AA batteries. Note: rechargeable batteries must be charged before use. See Battery

Information on page 11.

2. (Applies only to PFM R36) Insert the small plug mount microphone (MIC 014) into the “Mic Jack”

( ) on the top of the receiver. See FIG 7 below. Note: The MIC 014 cannot be used with the transmitter.

3. Plug the earphone or headphone into the “Headphone Jack” ( ) on top of the receiver. See FIG 6 / FIG 7.

Place the headphones on your head or earphone in your ear.

4. Turn the power on by rotating the “On/Off/FM Volume” knob clockwise. The “Power On Indicator” ( )

should illuminate green.

5. Select the desired operating frequency. Locate the “Channel Selector” inside the battery door (See FIG.

5). Use the supplied small screwdriver to rotate the switch to the desired channel (See FIG. 9, Page 10:

Channel Selection Chart).

FIG. 5: Battery Selection Switch /

ConFIGuration Controls

1 2 3

1. Tone Control 2. Channel Selector 3. Max Gain Control

Battery Selection Switch

FIG. 6: PFM R33 Top View FIG. 7: PFM R36 Top View

6. Adjust the receiver tone control to your needs. Locate the tone control inside the battery door. Use

the supplied small screwdriver to rotate the “Tone Control”. A low setting (fully counter-clockwise

“-”) emphasizes lower frequencies. A medium setting (rotated to a vertical position) has some low

frequency cut. A high setting (fully clockwise “+”) maximizes low frequency cut and emphasizes higher

frequencies.

Note: the earphone cord is also the receiving antenna. Do not bunch up the cord or wrap it

around the receiver. For best reception, the cord should hang as straight as possible.

7. Clip the receiver onto a belt or waistband, or slip it into a pocket (see Belt Clip Installation, page 10).

8. Check that the “FM Indicator” is illuminated yellow. Turn the “On/Off/FM Volume” knob to adjust the

volume to a comfortable listening level.

IMPORTANT: Make sure the receiver is turned OFF when not in use. Turn the “FM Volume” knob com-

pletely counter-clockwise. It should “click” and the “Power On” indicator should turn off.

ADJUSTING THE R36 VOLUME CONTROLS:

A. Adjust the left control, “On/Off/FM Volume”, to a comfortable listening level. Check that the

“FM Indicator” is illuminated yellow. Turn the volume knob clockwise until you are able to hear

audio from the transmitter.

B. Adjust the right control, “Mic”, volume second, turning it clockwise until you can hear sounds

picked up by the plug mount microphone.

C. Adjust the “Mic” and “On/Off/FM Volume” controls for a comfortable mix of FM and ambient

sounds.

MAX GAIN CONTROL

Adjust the “Max Gain” if you have sensitive hearing due to hearing loss. This feature limits the maximum

volume output by the receiver in case of sudden bursts of sound. To adjust the “Max Gain”, use the

supplied small screwdriver and turn it to a comfortable maximum volume level. In a fully clockwise posi-

tion the maximum volume is not reduced. In a fully counter-clockwise position, the maximum volume is

reduced by 17 to 20 dB.

LOW BATTERY INDICATOR

The “Power On” indicator (see FIG. 6/7, page 7) will ﬂash to indicate low battery. The listener may con-

tinue to use until the unit stops operating, then replace or recharge the batteries.

Andere Handbücher für Motiva PFM 360

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Williams Sound Empfänger Handbücher

Williams Sound

Williams Sound Personal PA PPA R7 Bedienungsanleitung

Williams Sound

Williams Sound WIR RX14 Montageanleitung

Williams Sound

Williams Sound Whisper R863 Montageanleitung

Williams Sound

Williams Sound PPA T46 Bedienungsanleitung

Williams Sound

Williams Sound Personal P.A. T18 Bedienungsanleitung

Williams Sound

Williams Sound Hearing Helper PFM 350 RCH Bedienungsanleitung

Williams Sound

Williams Sound TGS PRO 737 Leitfaden

Williams Sound

Williams Sound Portable FM Listening System TGS 173 Leitfaden

Williams Sound

Williams Sound WIR 135 Bedienungsanleitung

Williams Sound

Williams Sound Personal PA Receiver PPA R35N Montageanleitung

Williams Sound

Williams Sound DLR 360 Bedienungsanleitung

Williams Sound

Williams Sound Hearing Helper PFM R31 Bedienungsanleitung

Williams Sound

Williams Sound PPA VP 37 Leitfaden

Williams Sound

Williams Sound R16 Bedienungsanleitung

Williams Sound

Williams Sound WIR 125 Leitfaden

Williams Sound

Williams Sound HEARING HELPER TGS PRO 720 Leitfaden

Williams Sound

Williams Sound PPA R35-8 Montageanleitung

Williams Sound

Williams Sound SoundPlus WIR RX237 Bedienungsanleitung

Williams Sound

Williams Sound Digi-Wave DLT-100 Bedienungsanleitung

Williams Sound

Williams Sound T2 863 Bedienungsanleitung

Williams Sound

Williams Sound FM Listening System PPA 575 Bedienungsanleitung

Williams Sound

Williams Sound WIR SYS ADV Fehlerbehebungshandbuch

Williams Sound

Williams Sound TGS 100 Bedienungsanleitung

Williams Sound

Williams Sound TGS R30 Bedienungsanleitung

Beliebte Empfänger Handbücher anderer Marken

Garmin

Garmin GA 23 Bedienungsanleitung

Aiphone

Aiphone PS-12F Bedienungsanleitung

IMES

IMES TCS-01CA-PMI Bedienungsanleitung

BWI Eagle

BWI Eagle AIR-EAGLE SR Handbuch

AMIMON

AMIMON AMN12310 WHDI Bedienungsanleitung

Dual

Dual DMCPA79BT Betriebsanleitung

Sound Associates

Sound Associates SA652P Bedienungsanleitung

Sherwood

Sherwood NewCastle R-772 Bedienungsanleitung

Audio

Audio A10-RX Series Bedienungsanleitung

AllSee

AllSee PushShare PSRV1.1 Bedienungsanleitung

DEMAG

DEMAG DRC-DR D2 Bedienungsanleitung

Teleco

Teleco TVRCL868A02 Bedienungsanleitung

Bosch

Bosch RF3222E Bedienungsanleitung

Kramer

Kramer 631R Bedienungsanleitung

Xpress

Xpress xmc10 Bedienungsanleitung

JVC

JVC KD-MR1BTS Bedienungsanleitung

Omega Engineering

Omega Engineering UWTC-REC3 Bedienungsanleitung

e-survey

e-survey E300 Pro Bedienungsanleitung