Windsor VP6 Bedienungsanleitung

Service Guide

VP6 and VP10 Back Pack Vacuum

Repair Manual

Table of contents

Section 1: Introduction page 3

Section 2: Machine components page 4

Section 3: Tools Required page 5

Section 4: General Maintenance Page 6

Section 5: Electrical Troubleshooting Schematic Page 7

Section 6: Vacuum System Troubleshooting Pages 8-13

Section 1 Introduction

How the machine works:

The Vac Pac (VP6 and VP10) is a portable back pack vacuum cleaner intended for

commercial use.

The appliance is strapped to the operators back using a harness allowing the

operator to clean without having to move the appliance manually. The machine

uses a single motor in a canister with a hose and wand with multiple attachments

for various applications. The machine has two primary systems, the filtration system

and the vacuum system.

The filtration system consists of a micro (paper) bag a micro-Tex (cloth) bag and a

motor filter. An optional high efficiency filter kit is also available filtering at 99.98% at

0.3 microns.

The vacuum system consists of the canister body and single stage flow through

vacuum motor, there is no internal circuit breaker, the motor is protected by an

in-line fuse and a thermal cut-off switch for overload/overheat protection.

Section 2 Machine Components

1. Cap

2. Housing

3. Switch assembly

4. Power cord

5. Harness assembly

6. Accessories

7. Hose

8. Wand

9. Carpet tool

Section 3 Tools Required to repair the Vac Pac

1. #1 cross tip (Phillips) screw driver

2. #3 cross tip (Phillips) screw driver

3. Standard blade screw driver (Medium)

4. 15/16” open end wrench

5. AC line splitter for amperage testing, either hand made or purchased

6. Multi meter and amp clamp or combintation.

7. Needle nose pliers

8. Side cutters

9. Vacuum lift gauge

Section 4 General Maintenance

The Vac Pac is simple to maintain, the most important step to optimal performance of

the machine is to always use the cloth and micro paper filter together. The motor filter

in the canister can only be changed by removing the motor keeping the cloth bag

clean and changing the paper bag when full will prolong the life of the filter.

The vacuum motor is a flow trough type in which the air flows though the motor for

cooling recovering water with the Vac Pac will damage the motor.

To change the filter the motor must be removed, using a #1 Philips screw driver

remove the two black screws from the canister and pull the filter out through the bot-

tom of the machine, reverse the steps to replace the filter.

The Vac Pac when operating normally should produce 70 to 90 inches of lift

depending on the altitude.

Section 5 Electrical troubleshooting Schematic

The electrical system of the Vac Pac is simply switch operated, power in power out

trouble shooting principles are applied.

The entire machine is operated with one switch and protected by an in-line fuse and

thermal cut-off switch.

Section 6 Vacuum System Troubleshooting

Symptom:

Vacuum motor runs no suction:

Check for full bag or clogged hose, wand and accessory tool.

Vacuum motor runs for a while with weak suction then cuts off, this is caused

by the motor over heating above 170° F. When this occurs the vacuum motor is

not getting enough air flowing through it to keep it cool (flow through type).

Check for full bag or clogged hose, wand or accessory tool.

Yes The bag is full, or system is clogged, change bag or clear clogged

hose wand or accessory tool.

No If this condition has occurred frequently the motor may cut off at a

cooler temperature which indicates the thermal cut-off switch has

degraded over time due to frequent tripping. Replace the fuse

assembly which includes the thermal switch.

Problem resolved

Thermal switch and

fuse assembly

Vacuum System Troubleshooting

Vacuum runs but trips the circuit breaker in the building.

1. Using an amp clamp set on AC amperes and a current splitter at the wall outlet, turn the vacuum

motor on and check the reading, if the motor runs higher than 12 amps check the voltage at the

outlet if the voltage under load is less than 110 VAC the motor is starving for voltage and is

pulling excess amps to compensate. If the motor runs.at 8 to 12 amps and the wall breaker still

pops the breaker is weak and should be replaced.

If the amps are consistently above 15 when the wall breaker pops the motor needs to be

inspected for faults.

Once the determination has been made whether the circuit breaker is the issue or

the motor needs to be looked at, access to the vac motor is necessary.

Vacuum System Troubleshooting

To access the motor the machine needs to be disassembled following these steps.

1. Using a standard flat screwdriver Remove the four screws holding the harness to the housing

taking care not to lose the spacers on the bottom of the harness.

2. With the harness removed turn the housing upside down and remove the diffuser foam from the

bottom of the unit. You will see the plastic diffuser, remove the two small #1 Philips screws hold-

ing it to the motor.

3. On the housing there are three gray caps covering the motor mount screws, using a flat screw

driver remove the caps exposing the # 3 Philips head screws.

4. While holding the rubber well nuts inside on the motor, remove the screws releasing the motor

from the housing.

5. Disconnect the white switch wire from the thermal switch and the white cord wire from the motor

remove the motor from the housing.

11a. 2

33a. 4

Continued on page 10

Andere Handbücher für VP6

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Windsor Staubsauger Handbücher

Windsor

Windsor Versamatic Plus 10120380 Bedienungsanleitung

Windsor

Windsor NuWave Bedienungsanleitung

Windsor

Windsor Chariot 2 iVac 24 ATV CV2410125760 Bedienungsanleitung

Windsor

Windsor Zephyr Bedienungsanleitung

Windsor

Windsor RECOVER 18 Bedienungsanleitung

Windsor

Windsor 1.012-052.0 VSP14 Bedienungsanleitung

Windsor

Windsor Wave WAV 10125050 Bedienungsanleitung

Windsor

Windsor NuWave NWIFE 10125340 Bedienungsanleitung

Windsor

Windsor Chariot iCapsol CI24 Technische Daten

Windsor

Windsor Versamatic VSE I-3 Bedienungsanleitung

Windsor

Windsor PRS2 Bedienungsanleitung

Windsor

Windsor SRS15IE Bedienungsanleitung

Windsor

Windsor Carpet Maintainer IM 10066360 Bedienungsanleitung

Windsor

Windsor Sensor SRS12 Bedienungsanleitung

Windsor

Windsor SENSOR S12 Bedienungsanleitung

Windsor

Windsor VERSAMATIC VS14 Bedienungsanleitung

Windsor

Windsor AXCESS 12 1.012-061.0 Bedienungsanleitung

Windsor

Windsor Radius Mini Bedienungsanleitung

Windsor

Windsor NORTHWIND NWB 86284220 Bedienungsanleitung

Windsor

Windsor iCapsol Mini Deluxe Bedienungsanleitung

Windsor

Windsor Chariot iVacuum CV28 Technische Daten

Windsor

Windsor Sensor XP 12 Bedienungsanleitung

Windsor

Windsor Recover 18 1.013-017.0 Bedienungsanleitung

Windsor

Windsor SRXP12 10120240 Bedienungsanleitung

Beliebte Staubsauger Handbücher anderer Marken

Bissell

Bissell LittleGreen Proheat 1425 Series Bedienungsanleitung

Panasonic

Panasonic MC-YL637S147-AE Bedienungsanleitung

NEFF

NEFF N17XH10 0 Series Bedienungsanleitung

LG A9 Series Bedienungsanleitung

Oreck

Oreck Cordless Captura BK51700 Series Bedienungsanleitung

Kogan

Kogan KAVACROBVWA Bedienungsanleitung

Kränzle

Kränzle VENTOS 50 ID Benutzerhandbuch

EVVO

EVVO Ai35 Bedienungsanleitung

DeWalt

DeWalt DWH200D Bedienungsanleitung

Pontec

Pontec Pondomatic Vacuum Cleaner Bedienungsanleitung

Cleanmaxx

Cleanmaxx PC-P007E Bedienungsanleitung

Exido

Exido 240-114 Bedienungsanleitung

RIDGID

RIDGID WD1685AU0 Bedienungsanleitung

Ezviz

Ezviz RE4P Bedienungsanleitung

STG global

STG global TANVAC HDV3000 Bedienungsanleitung

Shark

Shark ROTATOR PRO COMPLETE NV550 Series Bedienungsanleitung

Factory

Factory M3340 Bedienungsanleitung

Shop-Vac

Shop-Vac VN92 SERIES Bedienungsanleitung