WPI NANOLITER2010 Bedienungsanleitung

Instrumenting scientiﬁc ideas

WORLD

PRECISION

INSTRUMENTS

NANOLITER2010

Nanoliter Injector with SMARTouch™ Controller

Serial No._____________________

www.wpiinc.com

QUICK START GUIDE

061217

Copyright © 2017 by World Precision Instruments. All rights reserved. No part of this publication may

be reproduced or translated into any language, in any form, without prior written permission of World

Precision Instruments, Inc.

Nanoliter 2010 with SMARTouch™ Controller

World Precision Instruments 1

Get started with your Nanoliter 2010 and SMARTouch™ Controller as quickly as

possible using these step by step instructions.

NOTE: This Quick Start Guide assumes that the operator back lled a micropipette

with mineral oil. For instructions on how to prepare the micropipette, see the

Nanoliter2010 Instruction Manual page 7.

1. Connect the AC power cord to the power supply unit and connect the power

supply unit to the MICRO2T controller. Plug the AC power cord into a wall outlet.

2 Connect the Nanoliter adapter cable to the output of channel 1 of the

SMARTouch™ controller and the RJ-11 connector of the Nanoliter2010 to the

RJ-11 female connector on the adapter. Make sure the embossed arrow on the

connector is facing upwards for proper pin alignment.

Adapter Cable connects to the

SMARTouch™ controller

Nanoliter 2010 Injector connection to

the adaper.

2 World Precision Instruments

3. Power on the unit. The following screen appears.

4. Touch the Initial Splash Screen anywhere. The MAIN MENU appears. Touch

DISPLAY ALL CHANNELS.

5. The syringe status screen appears. Press anywhere in the PUMP1 Display Area to

make Pump1 the active pump.

Nanoliter 2010 with SMARTouch™ Controller

World Precision Instruments 3

6. Touch the Congure button.

7. Press the Type box to bring up the Syringe Selection Screen.

8. In the Syringe Selection Screen, press the DWN key until you see the NL (Nanoliter

2010) type and press it. It will become highlighted. Then press Back to return to

the Pump Conguration Screen

4 World Precision Instruments

9. The CONFIGURATION screen appears. Touch the Volume Target display.

10. The Volume Target screen appears. Use the numerical keypad to enter 2500 nL.

Touch ENTER to set the volume and return to the CONFIGURATION screen.

11. Touch the DELIVERY RATE display.

Nanoliter 2010 with SMARTouch™ Controller

World Precision Instruments 5

12. The Volume Rate screen appears. Use the numerical keypad to enter a desired

injection rate in nL /sec. In this example, 500 nl/sec was entered. Touch ENTER to

set the delivery rate and return to the CONFIGURATION screen.

13. The Conguration screen shows that a target volume of 2500 nL was entered

and a delivery rate of 500 nL/s was entered. Touch BACK to return to the syringe

status {Home} screen.

14. Verify that the arrow inside the syringe is yellow and pointing in the injection

direction. If the arrow is not red and pointing to the left, touch DIRECTION to

change it. Touch the RUN button to start the injection.

6 World Precision Instruments

15. The injection will run until 2500 nL is injected and will then halt automatically.

Even though no injection actually happened, this will place the metal needle

plunger about 13.6 mm from the home (fully retracted) position. At this point

install the back lled micropipette on to the Nanoliter2010 injector as shown

below.

16. Press the DIRECTION button to change the direction to Withdraw. The arrow

turns green and points towards the back of the syringe depiction.

17. Press the CONFIGURE button.

Nanoliter 2010 with SMARTouch™ Controller

World Precision Instruments 7

18. Press the Volume Target area to bring up the Volume Target screen.

19. Use the keypad to enter the desired aliquot volume to be pulled into the

micropipette. We will enter 200 nL and press Enter.

20. Press the Delivery Rate area.

8 World Precision Instruments

21. Use the keypad to set the rate to 50 nL/sec and press Enter.

22. Press Back to go to the main Syringe information display.

23. Next place the micropipette tip into the aliquot to be loaded and press RUN. This

will pull 200 nL into the micropipette.

Dieses Handbuch passt für folgende Modelle

1

Andere WPI Laborausrüstung Handbücher

WPI

WPI Z-LITE Bedienungsanleitung

WPI

WPI LWCC-M-10 Bedienungsanleitung

WPI

WPI UltraPath 2 Stücklistenhandbuch

WPI

WPI MSI-150 Bedienungsanleitung

WPI

WPI REG2 Bedienungsanleitung

WPI

WPI ST5191 Bedienungsanleitung

WPI

WPI LWCC-M-10 Bedienungsanleitung

WPI

WPI MICRO-ePUMP Bedienungsanleitung

WPI

WPI CLEANRAY-2000 Bedienungsanleitung

WPI

WPI PV850 Bedienungsanleitung

WPI

WPI CLEANRAY-1000 Bedienungsanleitung

WPI

WPI M3301 Bedienungsanleitung

WPI

WPI Nanoliter 2000 Bedienungsanleitung

WPI

WPI SpectroPipetter SPT Bedienungsanleitung

WPI

WPI MPS-4 Bedienungsanleitung

WPI

WPI Eagle E2 Bedienungsanleitung

WPI

WPI NANOLITER2020 Bedienungsanleitung

Beliebte Laborausrüstung Handbücher anderer Marken

Qiagen

Qiagen DML 3000 Bedienungsanleitung

Queensgate

Queensgate NANOSCAN OP400 Programmierhandbuch

Conviron

Conviron GEN1000-GE Bedienungsanleitung

Parr Instrument

Parr Instrument 4560 Bedienungsanleitung

IKA

IKA IC control Bedienungsanleitung

Integra

Integra DOSE IT Bedienungsanleitung

Agilent Technologies

Agilent Technologies 5800 ICP-OES Bedienungsanleitung

Endress+Hauser

Endress+Hauser Cleanfit CPA875 Bedienungsanleitung

NI

NI PXI-5422 Handbuch

Collomix

Collomix Aqix Bedienungsanleitung

SPEX SamplePrep

SPEX SamplePrep 6875 Freezer/Mill Series Bedienungsanleitung

Ocean Insight

Ocean Insight FLAME-NIR+ Bedienungsanleitung

Parker

Parker ALIGN-MG-NA Bedienungsanleitung

BD

BD 644787 Bedienungsanleitung

DENTAURUM

DENTAURUM Compact Megaplus Bedienungsanleitung

Biuged Laboratory Instruments

Biuged Laboratory Instruments BGD 626 Bedienungsanleitung

VWR

VWR SAS Super IAQ Bedienungsanleitung

illumina

illumina MiSeqDx Bedienungsanleitung