Zavio D8520 Bedienungsanleitung

Motorized Outdoor Dome

86085A3000010

Please follow the installation steps below to set up Motorized Outdoor Dome IP

Camera.

Check the package contents against the list below. See P.1

Physical overview. See P.2

I/O Terminal Block Circuit. See P.3

I/O Terminal Block Pin Definition. See P.3

LED Indicator Definition. See P.4

Power mode. See P.4

Install the hardware and connect all cables. See P.5

Microsoft OS: Use the software CD to install Intelligent IP Installer. See P.8

Access the IP Camera using Intelligent IP Installer. See P.9

Mac OS using Safari Browser. See P.11

Change light environment setting. See P.12

Change the Web Interface into your preferred language. See P.12

Application of IP Camera. See P.13

For more information, please check the User Manual available in the Software CD.

Package Contents

Note:

Power Adapter and CAT5 cables are supplied by user. 2pin I/O terminal block is for

DC 12V Power Adapter used.

Camera

Motorized Outdoor Dome IP Camera

Quick

Installation

Guide

Brief product information and quick installation

Software CD

IP surveillance software

Intelligent IP Installer

User manuals

Language packs

Accessory

Mounting plate

Screw pack for wall and ceiling mounting

Alignment sticker

L-type hex key wrench

2pin I/O terminal block for power

Physical overview

Dome bubble

Conduit hole

Network / PoE

Lens

SD card slot

Reset

Network Link status indicator

Power status indicator

DC 12V/1.5A

Light Sensor

IR LEDs (16units,

Distance 20m)

I/O Terminal Block:

1: Ground,

2: +12VDC,

3: Audio in,

4: Audio out,

5: Digital Output 1,

6: Digital Output 2,

7: Digital Input 1,

8: Digital Input 2

Fan

RCA

Smart focus

control

NTSC/ PAL

switch

SD Card status indicator

I/O Terminal Block Circuit

I/O Terminal Block Pin Definition

This Camera provides an external I/O terminal block which is used to connect

input/ output devices. The pin definitions are described below.

Definition

Description

Max. V/A

Ground

+ 12VDC

12V DC

1.2 W

Audio In

Unbalanced, 1.4Vp-p, 1Vrms, terminal block

Audio Out

Unbalanced, 1.4Vp-p, 1Vrms, terminal block

Digital

Output 1

Uses an NPN transistor with the emitter

connected to the GND pin. If used with an

external relay, a diode must be connected in

parallel with the load for protection against

voltage transients.

100 mA

24V

Digital

Output 2

Uses an NPN transistor with the emitter

connected to the GND pin. If used with an

external relay, a diode must be connected in

parallel with the load for protection against

voltage transients.

100 mA

24V

Digital

Input 1

Connected to GND to activate, or leave

floating (or unconnected) to deactivate.

30V DC

Digital

Input 2

Connected to GND to activate, or leave

floating (or unconnected) to deactivate.

30V DC

LED Indicator Definition

LED

Color

Indication

Network

Blue

Steady blue for Network link

Flash blue while Network activity

Power

Red

Steady red for booting up process

Blue

Steady blue for booting up completion

Unlit

when reset button pressed for at least 5 sec.

to factory default

SD Card

Yellow

Steady yellow means SD card ready

Flashes yellow while accessing SD card

Reset: When the device is empowered, press the Reset Button to reboot the

device, or hold the Reset Button for

10 seconds to the settings back to factory default.

Reset process: Press reset button until indicator Unlitsteady red (booting up

process)steady blue (booting up completion)

Reset to default process: Press until indicator steady bluesteady red (booting

up process)steady blue (booting up completion)

Power Mode

PoE

Mode

Power

Requirement

PoE (IEEE802.3at) with Class 4

Power

Consumption

3.67W, without IR/ Fan

12.79 W, with max. IR on

5.04 W, with max. Fan on

14.05 W, with max. IR(100%) and Fan on

Power

Requirement

PoE (IEEE802.3af) with Class 3

Power

Consumption

3.67 W, without IR/ Fan

9.21 W, with max. IR on

5.04 W, with max. Fan on

10.81 W, with max. IR(70%) and Fan on

Adaptor

Mode

Power

Requirement

12V/1.5A Adaptor

Power

Consumption

3.67 W, without IR/ Fan

13.1 W, with max. IR on

5.04 W, with max. Fan on

14.26 W, with max. IR and Fan on

Note: Fan will be actived while the inner temparature above 50℃and will be

inactivated while it drops under 45℃.

(for F3105)

Install the hardware and connect all cables

A. Hardware installation

a. Connect the power adaptor to the supplied 2pin I/O terminal block. Please

make sure the red wire of the power adapter is connected with the positive

polarity of the terminal block.

b. Loosen the tamper-proof screws using supplied L-type Hex Key Wrench and

remove the dome cover. Be careful not to scratch the dome cover.

c. Disassemble the cable gland as shown in below illustration.

d. Feed the network and I/O cable through the sealing nut, claw and cable gland.

Connect the cables to the camera. Attach the cable gland to the conduit hole.

Push the claw into the cable gland and tighten the sealing nut to secure the

cables.

e. Use the supplied blind plug to fill unused conduit hole.

f. Use of the cable gland is optional. For vandal-proof requirement of the cables,

use vandal-proof conduits instead.

B. Wall mounting and ceiling mounting

a. Attach the alignment sticker to the wall/ceiling. Drill five holes into the wall,

four for screws and one for the cable. Then hammer the supplied plastic

anchors into the screw holes and secure the mounting plate with supplied

screws.

b. Attach the camera to the mounting plate and turn the camera clockwise until

the clips snap to the mounting plate.

c. Put the O-rings on the two supplied screws and fix the camera to the mounting

plate from inside with them to prevent unauthorized removal.

C. Connect all cables

c1. Without Power over Ethernet (PoE) connection

1. Connect the power adaptor to the IP Camera.

2. Connect the IP Camera to a normal Hub / Switch / Router.

c2. Power over Ethernet (PoE)

1. Connect the IP Camera to a PoE-enabled Hub /

Switch / Router.

Note:

If using a non-PoE switch, please use a PoE power injector to connect the camera.

D.To adjust the view angle- 3 axis mechanism design

1. Turn the lens module right and left to your desired pan position.

2. Turn the lens module up and down to your desire tile position.

3. Turn the lens module to adjust the image orientation to satisfied angle.

Important:

Do not rotate the IR LEDs so that it gets blocked by the housing as it will

affect the IR performance (as shown below). If the image is upside down,

please use the image rotate function in Video Setting.

E. Completion

1. Clean the dome bubble to remove the dust and finger print.

2. Fix the tamper-proof screws using supplied special hex. Be careful do not

scratch the cover glass.

3. The installation is complete now.

Microsoft OS: Use the software CD to install Intelligent IP Installer

Power on your PC and insert the CD-ROM. The setup page will show up

automatically. Please follow these steps to install the firmware.

Select “Intelligent IP Installer” and follow the installation process to

complete the installation.

Access the IP Camera using Intelligent IP Installer

1. Please check two settings before using Intelligent IP Installer .

a. Browser’s Internet Properties

→Security

→Default Level

b. Browser’s Internet Properties →

Privacy →Uncheck Pop-up Blocker

2. Click the Intelligent IP Installer Icon on your desktop. The main page will

show up listing all active camera and video server devices. Select the

relevant IP camera from the list and click Link to IE.

Andere Handbücher für D8520

Inhaltsverzeichnis

Andere Zavio Sicherheitskamera Handbücher

Zavio

Zavio F5110 Bedienungsanleitung

Zavio

Zavio D8520 Bedienungsanleitung

Zavio

Zavio CB5220 Bedienungsanleitung

Zavio

Zavio CB3210 Bedienungsanleitung

Zavio

Zavio F3100 Bedienungsanleitung

Zavio

Zavio B7210 Bedienungsanleitung

Zavio

Zavio CF7300 Bedienungsanleitung

Zavio

Zavio D6111 Bedienerhandbuch

Zavio

Zavio D611E Gebrauchsanweisung

Zavio

Zavio B6330 Bedienungsanleitung

Zavio

Zavio N6130 Gebrauchsanweisung

Zavio

Zavio D4320 Bedienungsanleitung

Zavio

Zavio F3101 Bedienungsanleitung

Zavio

Zavio B8210 Bedienungsanleitung

Zavio

Zavio B6110 Bedienungsanleitung

Zavio

Zavio B5010 Bedienungsanleitung

Zavio

Zavio F610A Gebrauchsanweisung

Zavio

Zavio CD5220 Bedienungsanleitung

Zavio

Zavio F312A Bedienungsanleitung

Zavio

Zavio CB3211 Bedienungsanleitung

Zavio

Zavio M511W Bedienungsanleitung

Zavio

Zavio F731E 35M Bedienungsanleitung

Zavio

Zavio F3101 Montageanleitung

Zavio

Zavio D610A Gebrauchsanweisung

Beliebte Sicherheitskamera Handbücher anderer Marken

Okina USA

Okina USA SIR36-870VF650LP Bedienungsanleitung

Divio

Divio NDR155PA Bedienungsanleitung

Canon

Canon VB-C500D Bedienungsanleitung

Easy Access

Easy Access EasyGuard Bedienungsanleitung

Vivotek

Vivotek FD9389-EHV-v2 Bedienungsanleitung

TUYA

TUYA COSMO W2 Bedienungsanleitung

Eusso

Eusso UNC7500-IR Einrichtungshandbuch

urmet domus

urmet domus 1096/204 Bedienungsanleitung

VC VC20 series Bedienungsanleitung

Axis

Axis Q1614 Bedienungsanleitung

ieGeek

ieGeek DD201 Bedienungsanleitung

VADDIO

VADDIO ClearVIEW HD-USB PTZ 999-6990-000 Bedienungsanleitung

Vicon

Vicon V662-D-1 Betriebsanleitung

Grundig

Grundig GCH-K0274P Bedienungsanleitung

Lorex

Lorex VANTAGE LBC7032 Bedienungsanleitung

4xem

4xem WPT Bedienungsanleitung

Samsung

Samsung SCV-3082 Bedienungsanleitung

Vitek

Vitek VTC-C544 Bedienungsanleitung