ZyXEL Communications Unified Security Gateway ZyWALL 300 Bedienungsanleitung

ZyWALL USG 300

Unified Security Gateway

Quick Start Guide

Version 2.00

7/2007

Edition 1

DEFAULT LOGIN

LAN Port 1

IP Address http://192.168.1.1

User Name admin

Password 1234

CONTENTS

ENGLISH 2

DEUTSCH 9

ESPAÑOL 16

FRANÇAIS 23

ITALIANO 30

日本語 37

РУССКИЙ 44

简体中文 51

繁體中文 57

ENGLISH

1 Checking the Package Contents

2 Rack-mounted Installation

Mount the ZyWALL in a 19-inch rack or place it on a sturdy, flat surface.

Note: Leave 10 cm of clearance at the sides and 20 cm in the rear.

1Align one bracket with the holes on one side of the ZyWALL and secure it with the included bracket

screws. Similarly, attach the other bracket.

2After attaching both mounting brackets, position the ZyWALL in the rack by lining up the holes in the

brackets with the appropriate holes on the rack. Secure the ZyWALL to the rack with the rack-mounting

screws.

Your package should

include one of each

of the following:

• ZyWALL USG 300

•Powercord

• Rack-mounting kit

• RJ-45 Ethernet cable

• RS-232 console Y-cable

• Printed Quick Start Guide

• Configuration Reference Card

• Compact disk (CD)

ENGLISH

3 Connecting the Hardware

Make sure that the power switch on the rear panel is turned off before you make the hardware connections.

1It is recommended that you configure the ZyWALL before using it to protect your network. Use an Ethernet

cable to connect a computer to port 1.

2Use another Ethernet cable(s) to connect port 2 and/or port 3to an Ethernet jack with Internet access.

3Use the included power cord to connect the power socket on the rear panel to a power outlet.

4Push the power switch to the on position and look at the front panel. The PWR light turns on. The SYS light

blinks during system testing and initialization and then stays on when the system is ready.

4 Web Login

1Launch your web browser and go to http://192.168.1.1 (the

ZyWALL automatically redirects you to https://

192.168.1.1).

ENGLISH

2Click Yes to proceed if you get a security alert or

certificate screen.

3Enter admin as the user name and 1234 as

the password. Click Login.

4It is strongly recommended that you change the

password. Type and retype a new password, and click

Apply.

ENGLISH

5 Installation Setup Wizard

Use an installation setup wizard to connect to the Internet and register the ZyWALL and/or activate trial

services, like IDP and content filter.

Note: Use the installation wizard only for initial configuration starting from the default configuration.

Changes you make in the installation wizard may not be applied if you have already changed the

ZyWALL’s configuration.

The Status screen

opens. Click the

Wizard icon in the

upper right corner.

•INSTALLATION SETUP, ONE ISP sets up a sin-

gle Internet connection for ge2.

•INSTALLATION SETUP, TWO ISP sets up Inter-

net connections for ge2 and ge3.

ENGLISH

6 Default Settings and Port Details

The ZyWALL is configured for the following network topology by default.

The wizard screens vary depending on the

encapsulation type you use. Refer to information

provided by your ISP and the web help screens to

know what to enter in each field. You can leave fields

blank if you don’t have that information.

ENGLISH

Note: The USB ports and extension card slots are reserved for future use.

7 Troubleshooting

Port Interface Zone IP Address and DHCP Settings Suggested Use With Default Settings

1ge1 LAN 192.168.1.1, DHCP server enabled Protected LAN

2, 3ge2, ge3 WAN DHCP clients Connections to the Internet

4, 5 ge4, ge5 DMZ None, DHCP server disabled Public servers (such as web, e-mail and

FTP)

6ge6 WLAN 10.59.0.1, DHCP server enabled Wireless access points

7ge7 None None, DHCP server disabled Optional

AUX aux None None Auxiliary modem

CONSOLE N/A None None Local management

Label Type Cable to Use

1~7 RJ-45 8-wire Category 5e or above Ethernet cable

AUX, CONSOLE RS-232 RS-232

Problem Corrective Action

None of the LEDs

turn on.

Make sure that you have the power cord connected to the ZyWALL and plugged in to an

appropriate power source. Make sure you have the ZyWALL turned on. Check all cable

connections.

If the LEDs still do not turn on, you may have a hardware problem. In this case, you should

contact your local vendor.

ENGLISH

8 Procedure to View a Product’s Certification(s)

1Go to www.zyxel.com.

2Select your product from the drop-down list box on the ZyXEL home page to go to that product's page.

3Select the certification you wish to view from this page.

Cannot access

the ZyWALL from

the LAN.

Check the cable connection between the ZyWALL and your computer or switch. Refer to

section 3 for details.

Ping the ZyWALL from a LAN computer. Make sure your computer’s Ethernet card is

installed and functioning properly. Also make sure that its IP address is in the same subnet

as the ZyWALL’s.

In the computer, click Start, (All) Programs, Accessories and then Command Prompt. In

the Command Prompt window, type "ping" followed by the ZyWALL’s LAN IP address

(192.168.1.1 is the default) and then press [ENTER]. The ZyWALL should reply.

If you’ve forgotten the ZyWALL’s password, use the RESET button. Press the button in for

about 5 seconds (or until the PWR LED starts to blink), then release it. It returns the ZyWALL

to the factory defaults (password is 1234, LAN IP address 192.168.1.1 etc.; see your User’s

Guide for details).

If you’ve forgotten the ZyWALL’s IP address, you can use the commands through the

console port to check it. Connect your computer to the CONSOLE port using a console

cable. Your computer should have a terminal emulation communications program (such as

HyperTerminal) set to VT100 terminal emulation, no parity, 8 data bits, 1 stop bit, no flow

control and 115200 bps port speed.

Cannot access

the Internet.

Check the ZyWALL’s connection to the Ethernet jack with Internet access. Make sure the

Internet gateway device (such as a DSL modem) is working properly.

Check ge2’s status in the Status screen. Use the installation setup wizard again and make

sure that you enter the correct settings.

Problem Corrective Action

DEUTSCH

1 Prüfen des Packungsinhalts

2 Rackmontage

Montieren Sie die ZyWALL an einem 19"-Rack oder stellen Sie es auf eine stabile Unterlage.

Hinweis: Lassen Sie seitlich 10 cm und hinten 20 cm Platz.

1Richten Sie eine Halterung an den Löchern an der Seite der ZyWALL aus und schrauben Sie sie mit den

mitgelieferten Montageschrauben fest. Verfahren Sie ebenso mit der zweiten Halterung.

2Wenn Sie beide Montagehalterungen befestigt haben, richten Sie die ZyWALL im so im Rack aus, dass

die entsprechenden Schraublöcher übereinander stehen. Befestigen Sie den ZyWALL mit den

Befestigungsschrauben am Rack.

Prüfen Sie ob alle

Teile vorhanden

sind:

• ZyWALL USG 300

• Netzkabel

• Rackmontage-Zubehör

• RJ-45-Ethernetkabel

• Y-Kabel für RS-232-Konsole

• Kurzanleitung in Druckform

• Konfigurationskarte

•CD

DEUTSCH

3 Anschließen der Hardware

Stellen Sie sicher, dass der Netzschalter an der Rückseite des Geräts ausgeschaltet ist, bevor Sie die

ZyWALL in Betrieb nehmen.

1Es wird empfohlen, die ZyWALL zu konfigurieren, bevor Sie sie zum in Ihrem Netzwerk einsetzen.

Schließen Sie einen Computer mit einem Ethernetkabel an Port 1 an.

2Schließen Sie an Port 2 und/oder Port 3Ihren Router mit Internetzugriff an.

3Schliessen Sie den Netzanschluss des Geräts (an der Rückseite) mit dem mitgelieferten Netzkabel an

eine Netzsteckdose an.

4Schalten Sie den Ein/Aus-Schalter in die Position On und sehen Sie sich das vordere Bedienfeld an. Die

PWR-LED beginnt zu leuchten. Die SYS-LED blinkt während des Systemtests und der Initialisierung, und

sie leuchtet, wenn der Test abgeschlossen und das System bereit ist.

4 Anmelden im Internet

1Starten Sie Ihren Internetbrowser und rufen Sie die Seite

http://192.168.1.1 auf (der ZyWALL leitet Sie automatisch

zur Seite https://192.168.1.1 weiter).

Andere Handbücher für Unified Security Gateway ZyWALL 300

Inhaltsverzeichnis

Sprachen:

Andere ZyXEL Communications Tor Handbücher

ZyXEL Communications

ZyXEL Communications ZyXEL ZyWALL USG-1000 Bedienungsanleitung

ZyXEL Communications

ZyXEL Communications ZYWALL 2 WG Bedienungsanleitung

ZyXEL Communications

ZyXEL Communications ADSL 2+ Security Gateway Bedienungsanleitung

ZyXEL Communications

ZyXEL Communications ZyAIR G-4100 Bedienungsanleitung

ZyXEL Communications

ZyXEL Communications ZYAIR B-4000 Bedienungsanleitung

ZyXEL Communications

ZyXEL Communications P-794H Bedienungsanleitung

ZyXEL Communications

ZyXEL Communications P-660H Series Bedienungsanleitung

ZyXEL Communications

ZyXEL Communications AMG1001-T Series Bedienungsanleitung

ZyXEL Communications

ZyXEL Communications P-660HW-TX Handbuch

ZyXEL Communications

ZyXEL Communications VSG-1200 Bedienungsanleitung

ZyXEL Communications

ZyXEL Communications nebula NSG Series Bedienungsanleitung

ZyXEL Communications

ZyXEL Communications P-870HW-I1 Bedienungsanleitung

ZyXEL Communications

ZyXEL Communications EMG3425-Q10A Bedienungsanleitung

ZyXEL Communications

ZyXEL Communications EMG8726-B10A Bedienungsanleitung

ZyXEL Communications

ZyXEL Communications P-660N-T1A Bedienungsanleitung

ZyXEL Communications

ZyXEL Communications ZYWALL USG 20W Bedienungsanleitung

ZyXEL Communications

ZyXEL Communications EMG2306-R10A Bedienungsanleitung

ZyXEL Communications

ZyXEL Communications SBG3300-N000 Bedienungsanleitung

ZyXEL Communications

ZyXEL Communications P-662H-D Series Bedienungsanleitung

ZyXEL Communications

ZyXEL Communications P-870HN-51B Handbuch

ZyXEL Communications

ZyXEL Communications ZYWALL P1 - V3.64 Bedienungsanleitung

ZyXEL Communications

ZyXEL Communications VMG1312-B Series Bedienungsanleitung

ZyXEL Communications

ZyXEL Communications ZyXEL ZyWALL 35 Bedienungsanleitung

ZyXEL Communications

ZyXEL Communications Unified Security Gateway ZyWALL 300 Bedienungsanleitung

Beliebte Tor Handbücher anderer Marken

LST

LST M500RFE-AS Bedienungsanleitung

Kinnex

Kinnex Media Gateway Bedienungsanleitung

2N Telekomunikace

2N Telekomunikace 2N StarGate Bedienungsanleitung

Mitsubishi Heavy Industries

Mitsubishi Heavy Industries Superlink SC-WBGW256 Bedienungsanleitung

Telsey

Telsey CPVA 500 - SIP Bedienungsanleitung

RTA

RTA 460A-NNA4 Technisches Datenblatt

Shaw

Shaw Gateway HDPVR Bedienungsanleitung

ABB

ABB VSN900 Kurzanleitung

Commander

Commander Pulse Bedienungsanleitung

2N Telekomunikace

2N Telekomunikace ATEUS EasyGate 501309E Bedienungsanleitung

NETGEAR

NETGEAR C6300BD Bedienungsanleitung

Amit

Amit CDW531AM Bedienungsanleitung

HMS

HMS Netbiter EasyConnect EC150 Bedienungsanleitung

Huawei

Huawei EchoLife HG620 Bedienungsanleitung

AT&T

AT&T U-verse 3801 Gebrauchs- und Pflegehandbuch

Logic IO

Logic IO RTCU MX2 turbo Bedienungsanleitung

Suttle

Suttle MediaMAX MXM-521 Bedienungsanleitung

RTA

RTA 460MCBC-N2E Technisches Datenblatt