ZyXEL Communications Prestige 660R-6 Series Handbuch

Prestige 660R-6x Read Me First

PORT CONNECTION

DSL Connect the DSL port on the Prestige to the wall jack using the included DSL cable (telephone wire).

Connect the micro filter(s) (optional – see the appendix in your User’s Guide for details) between the wall

jack and your telephone(s).

Be careful not to insert an RJ-11 connector into the RJ-45 port.

LAN 10/100M Use an Ethernet cable to connect this port to a computer (with an Ethernet card) or a hub (if your network

has more than one computer). The port is auto-negotiating (can connect at 10 or 100Mbps) and auto-

crossover (automatically adjust to straight-through or crossover Ethernet cable).

RESET You only need to use this button if you have forgotten the Prestige’s password or IP address. It returns the

Prestige to the factory defaults.

POWER Connect the end of the included power adaptor for your region to this power socket.

After you’ve made the connections, connect the power adaptor to a power supply and push in the power button to turn on the

Prestige.

LED COLOR STATUS DESCRIPTION

Green On The Prestige is receiving power.PWR

Off The Prestige is not receiving power.

On The Prestige is functioning properly.

Blinking The Prestige is restarting.

SYS Green

Off The Prestige is not ready or has malfunctioned.

LED COLOR STATUS DESCRIPTION

Red On The power to the Prestige is too low.

On The Prestige has a successful 10Mbps Ethernet connection.

Blinking The Prestige is receiving or sending data.

LAN 10M Green

Off No device is connected at 10Mbps.

Amber On The Prestige has a successful 100Mbps Ethernet connection.

Blinking The Prestige is receiving or sending data.

LAN 100M

Off No device is connected at 100Mbps.

On The Prestige is linked successfully to a DSLAM.

Blinking The Prestige is initializing the DSL line.

DSL Green

Off The DSL link is down.

Green Blinking The Prestige is sending or receiving non-PPP traffic.

On The Prestige has a PPP (PPPoA or PPPoE) connection.Amber

Blinking The Prestige is sending or receiving PPPoA or PPPoE traffic.

PPP/ACT

Off The Prestige is ready but not sending or receiving data.

Press the power switch in. The Power LED turns on. The SYS LED blinks and turns steady on. The

LAN and DSL LEDs turn on, if they are properly connected.

LAN IP Address 192.168.1.1 Default Password 1234

Subnet Mask 255.255.255.0 DHCP IP Pool 192.168.1.33 – 192.168.1.64

Your ISP (Internet Service Provider) or telephone company should give you most of the following information or pre-

configured the Prestige with it when you signed up for your Internet access account. You do not need to know every field.

REQUIRED INFORMATION

Virtual Path Identifier (VPI): ____________

Virtual Channel Identifier (VCI): ____________

Multiplexing (VC-based or LLC-based): VC LLC

Your device’s WAN IP Address (if given): __________________

Encapsulation:

RFC 1483

ENET ENCAP Ethernet Encapsulation Gateway IP Address: ____________________

PPPoA User Name: ____________ Password: ____________

PPPoE (PPPoE) Service Name: ____________

User Name: ____________ Password: ____________

All computers must have a 10M or 100M network card and TCP/IP installed. TCP/IP should already be installed on computers

using Windows NT/2000/XP, Macintosh OS 7 and later operating systems. See your User’s Guide for information on

configuring static IP address for your computer.

These procedures are for dynamic IP address assignment.

Setting up Your Windows 95/98/Me Computer

Installing TCP/IP Components

1. Click Start,Settings, Control Panel and double-click the Network icon.

2. The Network window Configuration tab displays a list of installed components.

To install TCP/IP:

a. In the Network window, click Add.

b. Select Protocol and then click Add.

c. Select Microsoft from the list of manufacturers.

d. Select TCP/IP from the list of network protocols and then click OK.

Configuring TCP/IP

1. In the Network window Configuration tab, select your network adapter’s TCP/IP entry and click Properties.

2. Click the IP Address tab. Click Obtain an IP address automatically.

3. Click the DNS Configuration tab. Select Disable DNS.

4. Click the Gateway tab. Highlight any installed gateways and click Remove until there is none listed.

5. Click OK to save and close the TCP/IP Properties window.

6. Click OK to close the Network window.

7. Turn on your Prestige and restart your computer when prompted. Insert the Windows CD if prompted.

Verifying TCP/IP Properties

1. Click Start and then Run. In the Run window, type "winipcfg" and then click OK to open the IP Configuration window.

2. Select your network adapter. You should see your computer's IP address, subnet mask and default gateway.

Setting up Your Windows NT/2000/XP Computer

Configuring TCP/IP

1. Click Start, Settings, Network and Dial-up Connections and right-click Local Area Connection or the connection you

want to configure and click Properties. For Windows XP, click start, Control Panel, Network and Internet

Connections and then Network Connections. Right-click the network connection you want to configure and then click

Properties.

2. Select Internet Protocol (TCP/IP) (under the General tab in Win XP) and click Properties.

3. The Internet Protocol TCP/IP Properties window opens. Click Obtain an IP

address automatically.

4. Click Obtain DNS server automatically.

5. Click Advanced, IP Settings tab and remove any installed gateways, then click OK.

6. Click OK to save and close the Internet Protocol (TCP/IP) Properties window.

7. Click OK to close the Local Area Connection Properties window.

8. Turn on your Prestige and restart your computer (if prompted).

Verifying TCP/IP Properties

1. Click Start, Programs, Accessories and then Command Prompt.

2. In the Command Prompt window, type "ipconfig" and then press ENTER. The window displays information about your

IP address, subnet mask and default gateway.

Setting up Your Macintosh Computer

Configuring TCP/IP Properties

1. Click the Apple menu, Control Panel and double-click TCP/IP to open the TCP/IP Control Panel.

2. Select Ethernet from the Connect via list.

3. Select Using DHCP Server from the Configure list.

4. Close the TCP/IP Control Panel.

5. Click Save if prompted, to save changes to your configuration.

6. Turn on your Prestige and restart your computer (if prompted).

Verifying TCP/IP Properties

Check your TCP/IP properties in the TCP/IP Control Panel.

Access the Prestige using the web configurator or the SMT via a telnet session.

Procedure For Web Configurator Configuration

1. Launch your web browser and enter “192.168.1.1” as the URL.

2. Type “admin” as the user name, "1234" (default) as the password and press ENTER.

3. You should now see the SITE MAP screen. Click the help icon (located in the upper right portion all screens) for online

HTML help.

Procedure For SMT Configuration via Telnet

1. Launch a Telnet program. In Windows, click Start and then Run.

2. Type “Telnet” followed by a space and the IP address of the Prestige,

(192.168.1.1 is the default) and click OK to display the password screen.

3. Enter “1234”, the default password, to access the SMT main menu. As you

type a password, the screen displays an asterisk “ * ” for each character you type.

PROBLEM CORRECTIVE ACTION

The PWR and/or SYS LEDs

are off.

Make sure the Prestige’s power adaptor is connected to the Prestige and plugged into an

appropriate power source. Check that the Prestige and the power source are both turned on.

Turn the Prestige off and on. If the error persists, you may have a hardware problem. In this

case, you should contact your vendor.

The LAN LED won’t turn on. Check the cable connection to the Prestige LAN port.

Make sure your computer network card is working properly.

The DSL LED is off. Check the connection between the Prestige DSL port and the wall jack.

I cannot access the SMT

menu.

The default SMT password is “1234”. If you have changed the password and have now

forgotten it, you will need to reset the Prestige or upload the default configuration file (see

User’s Guide).

Check that your computer IP address and the Prestige IP address are on the same subnet.I cannot access the web

configurator. If you changed the Prestige default LAN IP address then enter the new one as the URL.

Make sure you enter the correct user name and password. The default user name is “admin”

and the default password is “1234”. If you forgot your password, you have to reset the

Prestige. See the User’s Guide.

I cannot ping any computer

on the LAN.

If the 10/100M LAN LED is off, check the cables between the Prestige and your computer or

hub.

Check the TCP/IP configuration on your computer. Make sure that the IP address and the

subnet mask of the Prestige and the computers are on the same subnet.

I cannot access the Internet. Make sure the Prestige is turned on and connected to the network.

If the Prestige’s DSL LED is off, check the cable between the Prestige and the telephone wall

jack.

Make sure you entered your user name correctly. Your user name may be case-sensitive.

Inhaltsverzeichnis

Andere ZyXEL Communications Netzwerk-Router Handbücher

ZyXEL Communications

ZyXEL Communications P-660RU-T1 v3s Bedienungsanleitung

ZyXEL Communications

ZyXEL Communications XMG3512-B10A Bedienungsanleitung

ZyXEL Communications

ZyXEL Communications LTE3312-M432 Bedienungsanleitung

ZyXEL Communications

ZyXEL Communications Prestige 971M Bedienungsanleitung

ZyXEL Communications

ZyXEL Communications PRESTIGE 1400 - Bedienungsanleitung

ZyXEL Communications

ZyXEL Communications P-791R Bedienungsanleitung

ZyXEL Communications

ZyXEL Communications VMG8924 Bedienungsanleitung

ZyXEL Communications

ZyXEL Communications XGS4700-48F Bedienungsanleitung

ZyXEL Communications

ZyXEL Communications Prestige 964 Bedienungsanleitung

ZyXEL Communications

ZyXEL Communications ZyXEL ZyWALL P1 Bedienungsanleitung

ZyXEL Communications

ZyXEL Communications Prestige P-662HW-61 Bedienungsanleitung

ZyXEL Communications

ZyXEL Communications P-2302R-P1C Bedienungsanleitung

ZyXEL Communications

ZyXEL Communications LTE3202-M430 Bedienungsanleitung

ZyXEL Communications

ZyXEL Communications VMG3925 Bedienungsanleitung

ZyXEL Communications

ZyXEL Communications ES-2024 Series Bedienungsanleitung

ZyXEL Communications

ZyXEL Communications P-335WT Bedienungsanleitung

ZyXEL Communications

ZyXEL Communications ZYWALL 2 WG Bedienungsanleitung

ZyXEL Communications

ZyXEL Communications UAG Series Bedienungsanleitung

ZyXEL Communications

ZyXEL Communications P-2602R-DXA - Bedienungsanleitung

ZyXEL Communications

ZyXEL Communications G-6000 Bedienungsanleitung

ZyXEL Communications

ZyXEL Communications IES-1248-51V Bedienungsanleitung

ZyXEL Communications

ZyXEL Communications VES-1012 - Bedienungsanleitung

ZyXEL Communications

ZyXEL Communications P-791R V2 Bedienungsanleitung

ZyXEL Communications

ZyXEL Communications P964 APR 964 Bedienungsanleitung

Beliebte Netzwerk-Router Handbücher anderer Marken

Allnet

Allnet ALL0333AU Bedienungsanleitung

HomeSeer

HomeSeer HT-SEL Bedienungsanleitung

Sercomm

Sercomm Genesis OC3505D Bedienungsanleitung

Billion

Billion BIPAC 5102 Series Bedienungsanleitung

TP-Link

TP-Link TD-8817 Bedienungsanleitung

Motorola

Motorola MR1900 Bedienungsanleitung

Digi

Digi IX14 Bedienungsanleitung

Cisco

Cisco NCS 540 Handbuch

XAVi

XAVi X8821e Bedienungsanleitung

BEC

BEC 6200WZL Bedienungsanleitung

MikroTik

MikroTik hAP ac3 Series Bedienungsanleitung

Korenix

Korenix JetNet 5428G Series Bedienungsanleitung

NETGEAR

NETGEAR FS526T - Switch Bedienungsanleitung

Automated Logic

Automated Logic ZN551 Betriebsanleitung

Cisco

Cisco ASR 1000 Series Bedienerhandbuch

EnGenius

EnGenius ESR-9710 Bedienungsanleitung

Cisco

Cisco 805 Series Bedienungs- und Sicherheitshinweise

LevelOne

LevelOne FBR-1416 Bedienungsanleitung