ZyXEL Communications Prestige P660RU-T1 Bedienungsanleitung

ZyXEL

Firmware Release Note

Prestige P660RU-T1

Standard Version

Release 3.40(ST.5)C0

Date: November 17, 2005

Author: Sam Shi

ZyXEL Prestige 660RU-T1 Standard Version

Release 3.40(ST.5) C0

Release Note

Date: November 17, 2005

Supported Platforms:

ZyXEL Prestige 660RU-T1

Versions:

ZyNOS Version : V3.40(ST.5) | 11/17/2005 14:57:03

Bootbase Version : V1.03 | 04/26/2005 15:20:30

Notes:

P660R/RU-T1/T3/T7 is next generation of ZyXEL P623R series with higher speed of

ADSL2, ADSL2+ technology, speed up to 12Mbps (ADSL2) and 24 Mbps (ADSL2+).

With dual interface of USB and Ethernet, P660R/RU-61/63/67 offers the flexible way to

access the Internet.

Features:

Modification in V3.40(ST.5)C0 | 11/17/2005

1. Change to FCS

Modification in V3.40(ST.5)b3 | 11/9/2005

1. [Feature Enhancement]

Add reset button test Function

2. [Feature Enhancement]

Add PPPoE pass through when PC connect to device from USB interface

3. [BUG FIX] SPRID 051109589

Symptom: In SMT menu 4 and menu3.5 the ISP’s name and ESSID can not accept

special characters such as #$%^, but in eWC can accept it, they are not accordant

Condition: N/A

4. [BUG FIX] SPRID 051109596

Symptom: put rom-t has issue

Condition: after sys rom reset, put rom-t with right configurations, but device can’t

connect to internet

5. [BUG FIX] SPRID 051109598

Symptom: device can’t get IP from DHCP server after configure with wan node

command

Condition: no valid item in hunt table, vcautohunt is active, input wan node index

1, wan node vpi 0, wan node vci 33, wan node save, but device can’t get IP

Modification in V3.40(ST.5)b2 | 11/1/2005

1 [BUG FIX] SPRID: 051021682

Symptom: The display of CI command “wan atm vc webredir” has issue.

Condition: Step1: type in command “wan atm vc webredir”. It will show “usage:

webredict<enable 1 | disable 0>”

Step2: but type in command “wan atm vc webredir 1”, the webrediret is

disable.

type in command “wan atm vc webredir 0”, the webrediret is enable

2 [BUG FIX] SPRID: 051021684

Symptom: subnet mask error

Condition: 1. Log into the device via WEB GUI

2. Config Static WAN IP Address

3. Enter subnet mask ”255.255.248.0”

Then it will pop up a message shows ”subnet mask error”. However, ”

255.255.248.0”is a valid subnet

Modification in V3.40(ST.5)b1 | 10/19/2005

1.[Feature Enhancement]

Add CI command”WAN node”

Add CI command”sys password”

2. Add multiboot ver. 2.1

3. Change modem code to 3.2.0.7

Modification in V3.40(ST.4)C0 | 09/15/2005

1. Change default rom file according to 3.40(ST.3)C0

Modification in V3.40(ST.4)b2 | 08/24/2005

1. [FETURE ENHANCE]

Modify the zero configuration web pages according to PM’s requirement.

Modification in V3.40(ST.4)b1 | 08/17/2005

1 [BUG FIX] SPRID: 050817671

Symptom: the testing in progress page will consist endless

Condition: N/A

2 [BUG FIX] SPRID:

050817672

Symptom: Web redirect can not work well

Condition: When we input system password and PPPoE username/password and

press the save button, the settings are saved, but no connection testing window is shown up,

but still a window asking for the system password and PPPoE username/password again.

At this time, even if we ‘>d d 1’ in SMT, it can’t trigger PPPoE

3 [BUG FIX] SPRID:

050817675

Symptom: PPPOE/PPPOA idle timeout do not work

Condition: Step 1.:Set PPPOE idle timeout to 15 and PPPOE/LLC right username

password in menu4, Make sure PC can access the Internet

Step 2: Close all the programs that may send packets. Waiting at least 15s

Then the PPPOE is idle.

Step 3: And now, we can not access the web even if we ‘d d 1’ in SMT

except reboot the device.

4 [FETURE ENHANCE]

Add a new page zCfgTryAgain.html. This page will be showed when DSL line has not

up. Modified the zCfgPPPOE.html. Close web redirect once PPPOE user name and

password are right

5 [BUG FIX] SPRID:

050817677

Symptom: MSN message support has some problem.

Condition: While disable or enable UPNP function in DUT, the Windows XP MSN

6.2 and MSN 7.0 can not establish Whiteboard sharing functions.

6 [BUG FIX] SPRID: 050817679

Symptom:while set the DUT LAN “Client IP Pool Starting Address” and “Size of

Client IP Pool” which are not match the “IP Subnet Mask”, but this can be saved in

GUI\Wizard Setup and rom-t. In SMT and GUI\Advanced Setup have no this issue.

Condition: N/A

7 [BUG FIX] SPRID: 050817680

Symptom：

If the multicast stream speed goes up to 6Mb or higher then the P660 is not

able to keep up and the multicast stream starts to get choppy (this is brodcast tv signal

being streamed) and it gets unviewable. This goes on for awhile, then the device locks up

and you have to reboot to get it working again.

Condition: N/A

8. [FETURE CHANGED]

Change default romfile to Access Telecom version

Modification in V3.40(ST.3)C0 | 06/08/2005

1. Change to FCS

Modification in V3.40(ST.3)b2 | 06/01/2005

1. [BUG FIX] SPRID: 050525640

Symptom: Use backup function in GUI will make LAN pc and DUT WAN can not get

ip.

Condition: Step1 enter eWC->maintenance->configuration->backup.

Step2 backup current configuration.

Step3 in LAN pc can not get ip from DUT and DUT WAN can not get

dynamic ip.

2. [BUG FIX] SPRID: 050524562

Symptom: A problem about can’t get ip(enet encap/llc/dynamic)

Condition: 1. Use”sys romreset”in SMT 24.8

2. Go to WEB wizard or SMT 4, use enet encap/LLC/dynamic ip, set the

vpi/vci=0/33, then the device can’t get ip (use other vpi/vci is ok, our AUT-C set vpi/vci is

0/33).

3. [BUG FIX] SPRID: 050516864

Symptom: Use ax/4000 test UBR have problem

Condition: Set menu 4 ATM QoS Type= UBR, Peak Cell Rate (PCR) = 1000, Sustain

Cell Rate (SCR) = 500, Maximum Burst Size (MBS) =500, The traffic do not restrict by

the PCR, it can up to 1600 cells/s.

4. [FEATURE ENHENCE]

Routing Throughput Enhancement.

5. Change Default Rom-file

Add new rule into VC hunting table: VPI/VCI: 0/38 Encapsulation: PPPOA

Multiplexing: VC

Modification in V3.40(ST.3)b1 | 05/19/2005

1. [Bug Fix] SPRID: 050505225

Symptom: While use “Full Feature” mode in NAT in GUI, and configure rule in “Full

Feature”, but this NAT rule can not work. Then reboot DUT, this rule can works

properly.

Condition: Step1: In GUI/Advanced Setup/NAT, choose “Full Feature”.

Step2: In “Full Feature”, configure a NAT rule (For example: One-to-One,

or Many-to-One……).

Step3: While complete the setting, this NAT “Full Feature” rule can not

work. Then reboot DUT, this rule can works properly.

Step4: In SMT, it has no this issue.

2. [Bug Fix] SPRID: 050506301

Symptom: use pppoe encapsulation，get rom-t file from LAN pc change some

configuration and put the rom-t file, then pppoe login password will be change.

Condition: step1: use pppoe encapsulation, get rom-t file from LAN pc change some

configuration(such as system name->1234)

step2: put rom-t file from LAN pc ,after the DUT reboot, pppoe can not dial

up.

step3: change the pppoe login password then can dial up.

3. [Bug Fix] SPRID: 050310555

Symptom: in eWC can set DUT LAN ip to 0.0.0.0, in SMT menu3.2 when set it, it

warning “0.0.0.0 is not a valid IP address” they are not match.

Condition: N/A

4. [Bug Fix] SPRID: 050310549

Symptom: When 2 PCs visit eWC of DUT, the priority have some problem .

Condition: N/A

5. [Bug Fix] SPRID: 041222143

Symptom: in menu 24.11, leave the telnet server port default, upload firmware using

tftp from lan side pc, it always fails; but if telnet server port is changed to 23, the

function works well.

Condition: N/A

6. [Bug Fix] SPRID: 041124036

Symptom: 1.In Menu 24.8 typing ”ip ping 192.168.8.1” (the ip address from which

you can get response”.the default times of ping is three.

2.when the device get response in the first time or the second

time.type”ctrl+c”.then type the Up key and Enter quickly.the system will crash and

reboot.

Condition: N/A

7. [Bug Fix] SPRID: 050506307

Symptom: two LAN pc connect to DUT with anyip have problem.

Codition: step1 : use CI command “ip anyip enable yes” turn on DUT anyip

step2: LAN two pc set any ip out of DUT dhcp ip pool.

step3 when one LAN pc ping access DUT then another pc can not ping

access unless change the static ip.

8. [Bug Fix]

Symptom: there is always show testing on Web although Auto VC hunt finished and

failed.

Condition: N/A

9.[FETURE ENHANCE]

Supporting rom file back/restore via GUI .

10.[FETURE ENHANCE]

Modifying the 'Reset System' button ( MaintenanceÆdiagnosticÆGeneral) to 'Restart

the Device'.

Modification in V3.40(ST.2)C0 | 04/19/2005

1. Change to FCS firmware version.

Modification in V3.40(ST.2)b3 | 04/13/2005

2. [FEATURE CHANGE]

Symptom: Add Mbuf_Cache size for throughput improvement,

3. [FEATURE CHANGE]

Symptom: Add FTP_MALLOC.

4. [Bug Fix]

Symptom: VC-hunt causes sys exception.

5. [Bug Fix]

Symptom: The UPnP shows wrong link speed on WinXP PC.

6. [Bug Fix]

Symptom: Dialing messages shows up on console during VC-Hunt with PPPOE and

PPPOA

7. [Bug Fix]

Symptom: If we unplug ADSL line right after the ADSL just entered "wait for init

state" than ADSL will hold on this state and doesn't switch to down state, the CPU

loading is about 20% at the same time.

Modification in V3.40(ST.2)b2 | 03/17/2005

8. [FEATURE CHANGE]

Symptom: Add Mbuf_Cache to improve the throughput.

9. [Bug Fix]

Symptom: ATM Priority (UBR vs. CBR) scenario not correct.

10. [Bug Fix]

Symptom: In web wizard - LAN page. Change LAN IP for 192.168.1.1 to

192.168.181.1, the PC gets IP from the device but can't use IE to access device.

11. [Bug Fix]

Symptom: NAT_RuleList page display error in Mozilla.

12. [Bug Fix]

Symptom: In Lan page if type "255.255.248.0" in IP Subnet Mask will show "Subnet

Mask error".

13. [Bug Fix]

Symptom: Apply policy route rule to menu 3.2 or 11.3, the packet from LAN or WAN

can't route to gateway set in policy rule.

14. [Bug Fix]

Symptom: Set the MIB object “sysName” fail, this object doesn’t change but prompt

name of CI changed as what it set.

15. [Bug Fix]

Symptom: ATU-R can't link up after run the Loop test script for a spell.

16. [Bug Fix]

Symptom: Attainable downstream rate is 0 in ADSL2/ ADSL2+ mode, but it's normal

in ADSL1 mode.

17. [Bug Fix]

Symptom: ADSL sync up mode reset to default (ADSL2+) while sync up again.

Modification in V3.40(ST.2)b1 | 02/21/2005

1. [FEATURE CHANGE]

Symptom: Change DMT code form v3.0.10.3_A_TC to 3.0.11.22_A_TC for

supporting ADSL2/2+

Modification in V3.40(ST.1)b1 | 12/23/2004

2. [FEATURE CHANGE]

Symptom: Change default ROM file to disable UPNP.

3. [FEATURE CHANGE]

Symptom: Change the messages display format in CI Command “wan adsl chandata”

while the link up mode is ADSL2 and ADSL2+.

Modification in 3.40(ST.0)b1|10/22/2004

1. [FEATURE CHANGED]

Firmware downloads mechanism in Bootext is ready.

Modification in 3.40(ST.0)a2| 09/11/2004

2. [FEATURE CHANGED]

Symptom: Remove the centralize log and cli-for-smt for more system free memory.

Modification in 3.40(ST.0)a1 | 07/27/2004

1. Create this project.

ZyXEL Confidential

340ST5C0.doc 8/25

Internal Information:

1. Support ADSL2+ by TrendChip modem code DMT FwVer: 3.2.0.7_A_TC, HwVer:

T14F7_0.0

2. Support Multiboot client V2.1

Known Issues:

1. Ethernet and USB interfaces stop while ADSL is initializing.

2. The TR-067 Loop test failure.

3. If there are two or more PVCs with CBR or VBR QOS type and the total PCR

requirement exceed the line rate then the bandwidth distribution between those PVCs is

unpredictable.

4. Setup two PVCs with 1483 bridge, each PVC with 500Kbps upstream and 10Mbps

downstream traffic. If packet size is 1500 The CPU loading is 88%. The CPU loading

is 100% if packet size is 1024.

5. The VBR property of TrendChip is different form the others.

6. The value of MBS can’t be too large. Ex 10000.

7. F/W upgrade in eWC can not work with IE 5.0.3315.

8. MAC OS can’t login the WEBGUI through IE 5.2.

9. In MAC OS 10.1, USB interface can’t be detected after unplug USB cable.

10. In MAC OS 10.1, MAC PC will crash if USB cable was unplugged during data

exchanging between MAC PC and device by USB interface.

11. For CHT spec, there are two point fail but almost can reach the criteria

12. Use ax/4000 test VBR have problem.

13. Use ax/4000 test priority have problem in especially setting.

14. DUT will reboot automatically when DUT wan port is initialing and exist packet attack

from wan port, until the packet stops send to wan port of DUT, the DUT will recover

15. The Throughput does not meet the ADSL2+ criteria

16. The USB interface can't play IPTV (IGMP).

17. The debug information “[BrgStopShortCut] : Recover USB” has not been closed and it

affect auto test running smoothly.

18. In GUI, The WAN Backup functions need at least one none-zero Check WAN IP.

Modifications:

Modification in V3.40(ST.3)C0 | 06/08/2005

1. Change to FCS

Modification in V3.40(ST.3)b2 | 06/01/2005

1. [BUG FIX] SPRID: 050525640

Symptom: Use backup function in GUI will make LAN pc and DUT WAN can not get

ip.

Condition: Step1 enter eWC->maintenance->configuration->backup.

Step2 backup current configuration.

Step3 in LAN pc can not get ip from DUT and DUT WAN can not get

dynamic ip.

2. [BUG FIX] SPRID: 050524562

ZyXEL Confidential

340ST5C0.doc 9/25

Symptom: A problem about can’t get ip(enet encap/llc/dynamic)

Condition: 1. Use”sys romreset”in SMT 24.8

2. Go to WEB wizard or SMT 4, use enet encap/LLC/dynamic ip, set the

vpi/vci=0/33, then the device can’t get ip (use other vpi/vci is ok, our AUT-C set vpi/vci is

0/33).

3. [BUG FIX] SPRID: 050516864

Symptom: Use ax/4000 test UBR have problem

Condition: Set menu 4 ATM QoS Type= UBR, Peak Cell Rate (PCR) = 1000, Sustain

Cell Rate (SCR) = 500, Maximum Burst Size (MBS) =500, The traffic do not restrict by

the PCR, it can up to 1600 cells/s.

4. [FEATURE ENHENCE]

Routing Throughput Enhancement.

5. Change Default Rom-file

Add new rule into VC hunting table: VPI/VCI: 0/38 Encapsulation: PPPOA

Multiplexing: VC

Modification in V3.40(ST.3)b1 | 05/19/2005

1. [Bug Fix] SPRID: 050505225

Symptom: While use “Full Feature” mode in NAT in GUI, and configure rule in “Full

Feature”, but this NAT rule can not work. Then reboot DUT, this rule can works

properly.

Condition: Step1: In GUI/Advanced Setup/NAT, choose “Full Feature”.

Step2: In “Full Feature”, configure a NAT rule (For example: One-to-One,

or Many-to-One……).

Step3: While complete the setting, this NAT “Full Feature” rule can not

work. Then reboot DUT, this rule can works properly.

Step4: In SMT, it has no this issue.

2. [Bug Fix] SPRID: 050506301

Symptom: use pppoe encapsulation，get rom-t file from LAN pc change some

configuration and put the rom-t file, then pppoe login password will be change.

Condition: step1: use pppoe encapsulation, get rom-t file from LAN pc change some

configuration(such as system name->1234)

step2: put rom-t file from LAN pc ,after the DUT reboot, pppoe can not dial

up.

step3: change the pppoe login password then can dial up.

3. [Bug Fix] SPRID: 050310555

Symptom: in eWC can set DUT LAN ip to 0.0.0.0, in SMT menu3.2 when set it, it

warning “0.0.0.0 is not a valid IP address” they are not match.

Condition: N/A

4. [Bug Fix] SPRID: 050310549

Symptom: When 2 PCs visit eWC of DUT, the priority have some problem .

Condition: N/A

5. [Bug Fix] SPRID: 041222143

Symptom: in menu 24.11, leave the telnet server port default, upload firmware using

tftp from lan side pc, it always fails; but if telnet server port is changed to 23, the

function works well.

ZyXEL Confidential

340ST5C0.doc 10/25

Condition: N/A

6. [Bug Fix] SPRID: 041124036

Symptom: 1.In Menu 24.8 typing ”ip ping 192.168.8.1” (the ip address from which

you can get response”.the default times of ping is three.

2.when the device get response in the first time or the second

time.type”ctrl+c”.then type the Up key and Enter quickly.the system will crash and

reboot.

Condition: N/A

7. [Bug Fix] SPRID: 050506307

Symptom: two LAN pc connect to DUT with anyip have problem.

Codition: step1 : use CI command “ip anyip enable yes” turn on DUT anyip

step2: LAN two pc set any ip out of DUT dhcp ip pool.

step3 when one LAN pc ping access DUT then another pc can not ping

access unless change the static ip.

8. [Bug Fix]

Symptom: there is always show testing on Web although Auto VC hunt finished and

failed.

9. [FETURE ENHANCE]

Supporting rom file back/restore via GUI .

10.[FETURE ENHANCE]

Modifying the 'Reset System' button ( MaintenanceÆdiagnosticÆGeneral) to 'Restart

the Device'.

Condition: N/A

Modification in V3.40(ST.2)b1 | 02/21/2005

1. [BUG FIXED]

Symptom: Input the CI command "wan atm vc result" while DSL do not sync up, the

system will hang up.

Modification in V3.40(ST.1)C0| 01/14/2005

1. Change to FCS firmware version.

Modification in V3.40(ST.1)b4| 01/12/2005

1. [BUG FIXED]

Symptom: VC hunt causes system reboot, if the right hunting information in 10th entry

of VC hunt Table and VC hunt debug open.

2. [BUG FIXED]

Symptom: VC hunt has finished successful but connection fail page is redirected by

WEB.

Modification in V3.40(ST.1)b3| 01/05/2005

3. [BUG FIXED]

Symptom: Login device by FTP and enter ls or dir, then system reboot.

4. [BUG FIXED]

Symptom: When we get ROM-t from LAN side by FTP, and modified it by WordPad,

then put ROM -t, the device won’t accept the new ROM-t.

Modification in V3.40(ST.1)b2 | 01/04/2005

1. [BUG FIXED]

Symptom: When get ROM-t from LAN side by FTP, and modify it, then put ROM-t,

the DUT will show not enough memory.

Andere Handbücher für Prestige P660RU-T1

Inhaltsverzeichnis

Andere ZyXEL Communications Netzwerk-Router Handbücher

ZyXEL Communications

ZyXEL Communications Prestige 681 Bedienungsanleitung

ZyXEL Communications

ZyXEL Communications P-660R-T1 v3 Bedienungsanleitung

ZyXEL Communications

ZyXEL Communications ALC-1024L Bedienungsanleitung

ZyXEL Communications

ZyXEL Communications ETHERNET SWITCHES ES-1016 Bedienungsanleitung

ZyXEL Communications

ZyXEL Communications GS-1116A Bedienungsanleitung

ZyXEL Communications

ZyXEL Communications 650 Series Bedienungsanleitung

ZyXEL Communications

ZyXEL Communications ES-2024A Handbuch

ZyXEL Communications

ZyXEL Communications LTE7460-M608 Bedienungsanleitung

ZyXEL Communications

ZyXEL Communications ES-2024PWR Handbuch

ZyXEL Communications

ZyXEL Communications ADSL2+ Ethernet / USB Router P-660RU-Tx v2 Bedienungsanleitung

ZyXEL Communications

ZyXEL Communications Prestige 791R Bedienungsanleitung

ZyXEL Communications

ZyXEL Communications Prestige 645R-A Series Bedienungsanleitung

ZyXEL Communications

ZyXEL Communications Prestige 650 Bedienungsanleitung

ZyXEL Communications

ZyXEL Communications WSQ60 Bedienungsanleitung

ZyXEL Communications

ZyXEL Communications PRESTIGE 660 HW Series Bedienungsanleitung

ZyXEL Communications

ZyXEL Communications LTE3316 Series Bedienungsanleitung

ZyXEL Communications

ZyXEL Communications LTE7410 Bedienungsanleitung

ZyXEL Communications

ZyXEL Communications P-660RU-Tx Series Handbuch

ZyXEL Communications

ZyXEL Communications ZyWALL VPN2S Bedienungsanleitung

ZyXEL Communications

ZyXEL Communications UAG5100 Bedienungsanleitung

ZyXEL Communications

ZyXEL Communications ZyXEL Dimension ES-2108-F Bedienungsanleitung

ZyXEL Communications

ZyXEL Communications ZyXEL Prestige 202 Bedienungsanleitung

ZyXEL Communications

ZyXEL Communications ES-2108 Bedienungsanleitung

ZyXEL Communications

ZyXEL Communications Multy Plus Bedienungsanleitung

Beliebte Netzwerk-Router Handbücher anderer Marken

Allnet

Allnet ALL0333AU Bedienungsanleitung

HomeSeer

HomeSeer HT-SEL Bedienungsanleitung

Sercomm

Sercomm Genesis OC3505D Bedienungsanleitung

Billion

Billion BIPAC 5102 Series Bedienungsanleitung

TP-Link

TP-Link TD-8817 Bedienungsanleitung

Motorola

Motorola MR1900 Bedienungsanleitung

Digi

Digi IX14 Bedienungsanleitung

Cisco

Cisco NCS 540 Handbuch

XAVi

XAVi X8821e Bedienungsanleitung

BEC

BEC 6200WZL Bedienungsanleitung

MikroTik

MikroTik hAP ac3 Series Bedienungsanleitung

Korenix

Korenix JetNet 5428G Series Bedienungsanleitung

NETGEAR

NETGEAR FS526T - Switch Bedienungsanleitung

Automated Logic

Automated Logic ZN551 Betriebsanleitung

Cisco

Cisco ASR 1000 Series Bedienerhandbuch

EnGenius

EnGenius ESR-9710 Bedienungsanleitung

Cisco

Cisco 805 Series Bedienungs- und Sicherheitshinweise

LevelOne

LevelOne FBR-1416 Bedienungsanleitung