ACME BW-54-10FC II RL Bedienungsanleitung

TABLE OF CONTENTS

1. Safety Instructions.........................................................................................................2

2. Techical Specfications ..................................................................................................3

3. Installation......................................................................................................................4

4. How To Set The Fixture .................................................................................................5

4.1 Control Panel..........................................................................................................5

4.2 Main Functions.......................................................................................................6

5. How To Control The Unit.............................................................................................10

5.1 Master/Slave Built In Preprogrammed Function...............................................11

5.2 DMX Controller.....................................................................................................11

5.3 DMX 512 Configuration .......................................................................................12

5.4 DMX512 Connection............................................................................................14

6. Troubleshooting...........................................................................................................15

7. Cleaning and Maintenance..........................................................................................16

1. Safety Instructions

WARNING

Please keep this User Guide for future consultation. If you sell the unit to another user,

be sure that they also receive this instruction booklet.

Caution

：

All fixtures are intact from the manufacturer, please operate follow up the user manual,

artificial fault are not under guarantee repair.

Unpack and check carefully there is no transportation damage before using the unit.

Do install and operate by operator.

Use safety chain when fixes the unit.

The unit must be installed in a location with adequate ventilation, at least 50cm from

adjacent surfaces.

Be sure that no ventilation slots are blocked, otherwise the unit will be overheated.

Before operating, ensure that the voltage and frequency of power supply match the

power requirements of the unit.

It’s important to ground the yellow/green conductor to earth in order to avoid electric

shock.

Maximum ambient temperature is Ta: 40℃. DO NOT operate it where the temperature

is higher than this.

Don’t connect the device to any dimmer pack.

First run, there will be smoke or smells, and all disappearing a few minutes later.

Make sure there are no flammable materials close to the unit while operating, as it is fire

hazard.

Look over power wires carefully, replace immediately if there is any damage.

Unit surface temperature may reach up to 85℃. Don’t touch the housing bare-hand

during its operation.

Never run on for a long time lest shortening lifespan.

Avoid any inflammable liquids, water or metal objects entering the unit. Once it happen,

cut off the mains power immediately.

Do not operate in dirty and dusty environment, also cleaning fixtures regularly.

Please read the instructions carefully

which includes

important information about the installation, operation

and maintenance.

Do not allow children to operate the fixture.

Do not touch any wire during operation as there might be a hazard of electric shock.

Avoid power wires together arounding other cables.

Replace fuse only with the same type.

In the event of serious operating problem, stop using the unit immediately.

Never turn on and off the unit time after time.

The housing, the lenses, or the ultraviolet filter must be replaced if they are visibly

damaged.

Do not open the unit as there are no user serviceable parts inside. Never try to repair

the unit by yourself. Repairs carried out by unskilled people can lead to damage or

malfunction. Please contact the nearest authorized technical assistance center.

Disconnect the mains power if the fixture is not used for a long time.

Do use original packing materials once transport it again.

Do not look directly at the LED light beam while the fixture is on.

To protect the machine, power off 10s rear can electrify.

2. Techical Specfications

BW-54-10FC II RL: 54pcs x10W CREE Quad Color Building Wash with Built-in LED

Display for Rental Application.

BW-54-10FC II WT RL: with Built-in Wireless Receiver and LED Display for Rental

Application.

Light source

：

10W LED x 54pcs

Voltage

：

AC 100-240V/50Hz~60Hz

Power consumption

：

568W

Lens Option

：

20°, 30°, 40°, 60°

IP

：

Dimension

：

748X446X422 mm

Weight

：

43.1kg

446

748

422

3. Installation

The fixture can be placed directly on the stage floor which can support 10 times of the

fixture’s weight or can be rigged on the structure via two omega clamps in the positions you

want. Ensure that the structure (truss, wall) to which you are attaching the unit is secure.

Mounting holes are intended for permanent installation on the flat surface, especially in the

wall installation. Safety ropes that can hold 12 times of the weight of the fixture are needed

when you want to hang the fixture. Enhanced care has to be considered during the

installation.

The equipment must be fixed by professionals.

Note：Range of mounting height is 0~30m.

When using the fixture as fixed installation at outdoor place, please remove the Nut for

Omega Clamp to avoid rusting.

4. How To Set The Fixture

4.1 Control Panel

①：

Power

Water proof connectors for power input.

②：

DMX input

Water proof connectors for DMX 512 operation,

3-pin XLR cable to input DMX signal.

③：

DMX output

Water proof connectors for DMX 512 operation,

3-pin XLR cable to output DMX signal.

④：

Display and Button:

Display: To show the menu and the selected functions.

Button:

Caution: If the unit is used for fixed installation outdoor, be sure to put the metal cover

equipped on top of the LED display, failing to do it may cause the water infiltration problem

after been used for more than 1 year outdoor.

To select the programming functions

DOWN

To go backward in the selected functions

To go forward in the selected functions

ENTER

To confirm the selected functions

4.2 Main Functions

Open the metal cover and remove it then you can set the menu manually. To select any

functions, press MENU button until the required one is shown on the display. Select the

function by ENTER button and the display will blink. Use DOWN and UP button to change

the mode. Once the required mode has been selected, press ENTER button to setup or it

will automatically return to the main functions without any change after idling one minute.

Back to the functions without any change press MENU button. The main functions are

shown below:

Once you set to , after running in show mode for 1

minute without any change or restarting the unit, the key board

become locked. Press ENTER button to enable the menu, the

display will show

, press UP and DOWN button until it

shows password you have set before,

then press ENTER to

unlock. initial password is .

DMX 512 Address Setting

1. Press the MENU button until is displayed. Press ENTER.

2. The current address will now be displayed and flashing. Press the UP or DOWN

buttons to find your desired address. When you have found your desired DMX address

press ENTER to confirm or automatically exit menu mode without any change after one

minute. Back to the functions without any change press MENU button.

Channel Mode

1. Press the MENU button until is displayed. Press ENTER. Either

（4channel mode）or （5 channel mode）or (7 channel mode)

(8 channel mode) or （10channel mode）will be displayed.

2. Press the UP or DOWN buttons to choose your desired DMX mode and press ENTER

to confirm and exit. Or automatically exit menu mode without any change after one

minute. Back to the functions without any change press the MENU button.

Fade Mode

1. Press the MENU button until is displayed. Press ENTER.

2. Press the UP or DOWN buttons to adjust the fade speed to your desire, 0 being the

fastest fade and 255 being the slowest.

3. When you find your desired fade speed, press ENTER to confirm or automatically exit

menu mode without any change after one minute, Back to the functions without any

change press MENU button.

Color Setup

1. Press the MENU button until is displayed. Press ENTER. will now be

displayed, press ENTER, Use the UP or DOWN buttons to adjust to your desired

intensity(0~255). Press ENTER after the intensity adjustment.

2. After you press ENTER then press UP and will be displayed, press ENTER,

Use the UP or DOWN buttons to adjust the value from 0 to 255.

3. Follow these steps to make adjustments of and until your desired color

is reached. After adjusting , press ENTER then press the UP button.

4. （Dimmer）will be displayed, press ENTER, this is the master dimmer control. In

this submenu you can adjust the intensity of your created color. Use the UP or DOWN

buttons to adjust the intensity from 0 to 255.

5. Press ENTER once you have adjusted the master dimmer, Press the UP button and

（Strobe）will be displayed. This is the strobe function. If you choose to activate

strobe, press ENTER. Use the UP or DOWN buttons to adjust the speed of the strobe,

choose 0 to turn the strobe off and 255 being the fastest strobe. Press ENTER once

you have made your adjustments.

6. Once your desired color and settings are reached, press ENTER to confirm or

automatically exit menu mode without any change after one minute, Back to the

functions without any change press MENU button.

Adjust White Balance

1. Press the MENU button until is displayed. Press ENTER. Either (Red

1), (Green 1), (Blue 1), (Red 2), (Green 2) or

(Blue 2) will be displayed.

2. Press the UP or DOWN buttons to find your desired color and press ENTER to confirm.

3. Using the UP or DOWN buttons adjust the value (125~255) to your desire.

4. When you find your desired White Balance value, press ENTER to confirm or

automatically exit menu mode without any change after one minute. Back to the

functions without any change press MENU button.

Cipher Setup

1. Press the MENU button until is displayed. Press ENTER.

2. will now be displayed and flashing. Press the UP or DOWN buttons to adjust

the password (0~9999) to your desire.

3. When you find your desired password, press ENTER to confirm or automatically exit

menu mode without any change after one minute. Back to the functions without any

change press MENU button.

Key Lock

1. Press the MENU button until is displayed. Press ENTER. Either or

will be displayed.

2. Press the UP or DOWN buttons to select (lock the key board) or

(normal). Once select, press ENTER to confirm or automatically exit menu mode

without any change after one minute, Back to the functions without any change press

MENU button.

Blackout Mode

1. Press the MENU button until is displayed, Press ENTER. Either or

will be displayed.

2. To activate Blackout, press UP or DOWN buttons until is displayed, press

ENTER to confirm and exit, the fixture will now be in Blackout mode. To deactivate

Blackout mode, select and press ENTER.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere ACME Beleuchtungsausrüstung Handbücher

ACME

ACME LED-747-1W Bedienungsanleitung

ACME

ACME DAZZLED COLORLED-430 Bedienungsanleitung

ACME

ACME Glamour 350Z Bedienungsanleitung

ACME

ACME BTDG40 Bedienungsanleitung

ACME

ACME LED-SC25 Bedienungsanleitung

ACME

ACME Whack Bedienungsanleitung

ACME

ACME Inferno Bedienungsanleitung

ACME

ACME V-BOX Bedienungsanleitung

ACME

ACME DELUGE LED-WAV-50W Bedienungsanleitung

ACME

ACME PIXEL LINE IP Bedienungsanleitung

ACME

ACME TRACK 10 Bedienungsanleitung

ACME

ACME XP-280 BS Bedienungsanleitung

ACME

ACME ASTRO LED-256D Bedienungsanleitung

ACME

ACME STAGE PAR 400 ZOOM IP Bedienungsanleitung

ACME

ACME Thunderstruck LP-2304 Bedienungsanleitung

ACME

ACME LED-900 A Bedienungsanleitung

ACME

ACME SABER HYBRID PRO Bedienungsanleitung

ACME

ACME GLORV FRAMING XP-5000SZF Bedienungsanleitung

ACME

ACME ENERGY SPOT XA-400 SPOT Bedienungsanleitung

ACME

ACME Energy Spot PRO Bedienungsanleitung

ACME

ACME Spider FC Bedienungsanleitung

ACME

ACME MP-12FC Bedienungsanleitung

ACME

ACME Stage Par 220MP-220 Bedienungsanleitung

ACME

ACME Thunder Bedienungsanleitung

Beliebte Beleuchtungsausrüstung Handbücher anderer Marken

Brizo

Brizo 8SP-MU-4 Bedienungsanleitung

LUCE&LIGHT

LUCE&LIGHT BROM 1.0 Bedienungsanleitung

IKEA

IKEA BJÖRKSPIREA Bedienungsanleitung

Laserworld

Laserworld Evolution Series ES-400RGB Bedienungsanleitung

EuroLite

EuroLite LED B-40 Bedienungsanleitung

Qazqa

Qazqa Suplux SL 3 Black 103062 Bedienungsanleitung

Commercial Electric

Commercial Electric 54568141 Bedienungsanleitung

CREE LIGHTING

CREE LIGHTING 304 Series Bedienungsanleitung

Goobay

Goobay 49867 Bedienungsanleitung

ECOMAN ITALIA

ECOMAN ITALIA LED T8 Bedienungsanleitung

Alkalite

Alkalite Krypton KT-81 Bedienungsanleitung

Clas Ohlson

Clas Ohlson GU10 Bedienungsanleitung

DTS

DTS DELTA 10 F Bedienungsanleitung

ring

ring Solar Steplight Bedienungsanleitung

One Stop Gardens

One Stop Gardens 57696 Montageanleitung

SIREM

SIREM Swimeo A2 Bedienungsanleitung

Silvair

Silvair MESH-CEDRP Bedienungsanleitung

S&P

S&P PCRL80 Bedienungsanleitung