ACME Thunderstruck LP-2304 Bedienungsanleitung

LP-2304

1. Safety Instructions............................................................................................................................2

2. Technical Specifications....................................................................................................................3

3. Installation and Connection .............................................................................................................4

4. How to set the unit...........................................................................................................................5

4.1 Rear Panel.......................................................................................................................................5

4.2 Main Function.................................................................................................................................6

5. How to control the unit ..................................................................................................................12

6. DMX512 configuration ...................................................................................................................13

7. DMX512 Connection.......................................................................................................................15

8.Troubleshooting...............................................................................................................................16

9. Fixture Cleaning..............................................................................................................................17

1. Safety Instructions

WARNING

Please keep this User Manual for future consultation. If you sell the fixture to another user, be sure

that they also receive this instruction booklet.

Please unpack and check carefully there is no transportation damage before using the fixture.

Please disconnect main power before servicing and maintenance.

The unit must be installed in a location with adequate ventilation, at least 50cm from adjacent

surfaces. Be sure that no ventilation slots are blocked.

The ambient temperature is Ta: 0℃-40℃. DO NOT operate it where above or below the range of

temperature.

DO NOT connect the device to any dimmer pack.

The housing must be replaced if they are visibly damaged.

Unit surface temperature may reach up to 85℃. Don’t touch the housing bare-hand during its

operation. Turn off the power and allow about 15 minutes for the unit to cool down before replacing

or serving.

There are no user serviceable parts inside the fixture. Do not open the housing or attempt any

repairs by yourself. In the unlikely event your fixture may require service, please contact your nearest

dealer.

In the event of serious operating problem, stop using the fixture immediately. Never try to repair the

fixture by yourself. Repairs carried out by unskilled people can lead to damage or malfunction. Please

contact the nearest authorized technical assistance center. Always use the same type spare parts.

Installation:

The unit is fully operational in three different mounting positions, hanging upside-down from a

ceiling or set on a flat level surface. To avoid internal damage to the unit, never mount the unit on its

side as illustrated above. Be sure this fixture is kept at least 0.5m away from any flammable materials

(decoration etc.). Always use and install the supplied safety cable as a safety measure to prevent

accidental damage and/or injury in the event the clamp fails.

Please read the instruction carefully which includes important

information about the installation, usage and maintenance.

1. Bolt each clamp to the Omega holder with screw and lock nut through the hole in the holder.

2. Faster the omega holders on the bottom of the base by inserting quick-lock fasteners into the

holes of the base and tighten fully clockwise.

3. Hang the fixture to the support through clamp and faster the screws, Faster the safety cable

through the bottom of the base and over the support.

2. Technical Specifications

13 channel Modes;

Ideal for discotheques, clubs, bars, parties, Mobile DJs, etc.

Input Voltage: AC100V~240V，50/60Hz

Total Power consumption:1500W

Power Cord Daisy Chain: 1Fixtuer(120V); 2 Fixtuer(220V);

Beam Angle:110°

IP Grade: IP 65

LED Sources: 0.4W RGBW x 2304

Dimension: 623x123x387mm

Weight: 16 Kgs

3. Installation and Connection

The unit should be mounted via its screw holes on the bracket. Always ensure that the unit is firmly fixed

to avoid vibration and slipping while operating. Always ensure that the structure to which you are

attaching the unit is secure and is able to support a weight of 10 times of the unit’s weight. Also always

use a safety cable that can hold 12 times of the weight of the unit when installing the fixture.

The equipment must be fixed by professionals. And it must be fixed at a place where is out of the touch

of people and has no one pass by or under it. The unit should be mounted in the height of 0 to 30m.

Method for using lamp hook and safety rope

4. How to set the unit

4.1 Rear Panel

○

1Display: Show the various menus and the selected functions；

○

2Button：

To select the programming functions

DOWN

To go forward in the selected functions

To go backward in the selected functions

ENTER

To confirm the selected functions

○

3Breathable punishment

○

4Power input/output

For DMX512 link, use 3/5-pin XLR plug cable to input DMX signal, and to link the next unit.

○

5DMX input/output:

For DMX512 link, use 3/5-pin XLR plug cable to input DMX signal, and to link the next unit.

○

6Ethernet in/ Ethernet Thru:For ArtNet link

4.2 Main Function

To select any functions, press MENU button until the required one is shown on the display. Select the

function by ENTER button. Use DOWN and UP button to change the mode. Once the required mode has

been selected, press ENTER button to setup or it will return to the main functions without any change

after idling 8 seconds automatically. Back to the functions without any change press MENU button. The

main functions are shown below:

DMX Setting

Select the DMX Setting, press the ENTER button and the display will blink. Use the DOWN and UP

button to change the DMX 512 address（001-512）or Elthernet Setup,In Elthernet Setup menu,fixture

Elthernet parameter ,IP Address/Subnet Mask/Net(0-127)/Subnet(0-15)/Universe(0-15) ,Must be

consistent with the value of the controller，Fixture receives the corresponding ArtNet signal control.

Once the address has been selected, press the ENTER button to setup or exit menu mode without any

change after 8 seconds automatically. Back to the previous functions without any change press the

MENU button.

Channel Mode

Select the Channel Mode, press the ENTER button. Use the DOWN and UP button to select the Channel,

there are 13 channel Modes. Once selected, press the ENTER button to store. Press the MENU button

back to the last menu without any change or idling 1 minute to exit menu mode.

DMX Last State

Select the DMX Last State, press the ENTER button. Use the DOWN and UP button to select Blackout or

Hold . Once selected, press the ENTER button to store. Press the MENU button back to the last menu

without any change or idling 8 seconds to exit menu mode.

Dimmer curve

Select the Dimmer curve, press the ENTER button. Use the DOWN and UP button to select the curve you

need. Once selected, press the ENTER button to setup or exit menu mode without any change after 8

seconds. Back to the functions without any change press the MENU button again.

Dimmer mode 1 Dimmer mode 2 Dimmer mode 3 Dimmer mode 4

Optically Linear Square Law Inverse-Square Law S-Curve

Mode 1(Optically Linear): The increase in light intensity appears to be linear as DMX value is increased.

Mode 2(Square Law): Light intensity control is finer at low levels and coarser at high levels.

Mode 3(Inverse Square Law): Light intensity control is coarser at low levels and finger at high levels.

Mode 4(S-cure): Light intensity control is finger at low levels and high levels and coarser at medium

levels.

Dimmer Speed

Select the Dimmer Speed, press the ENTER button. Use the DOWN and UP button to select Fast or

Smooth. Once selected, press the ENTER button to setup or exit menu mode without any change after 8

seconds. Back to the functions without any change press the MENU button again.

White Balance

Select the White Balance, press the ENTER button to confirm. It can be adjusted with the whole fixture,

or it can be adjusted independently for each block.Use the UP and DOWN button to select

Red/Green/Blu/White,press the ENTER button to store, then use the UP and DOWN button to adjust

the value from (125~255), press the ENTER button to confirm. (DMX signal will be the first priority under

Manual Mode.) Once selected, press the ENTER button to store. Press the MENU button back to the last

menu without any change or idling 8 seconds to exit menu mode.

Language

Select the Language, press the ENTER button to confirm. Use the UP and DOWN button to adjust

English or Chinese .Once selected, press the ENTER button to store. Press the MENU button back to the

last menu without any change or idling 8 seconds to exit menu mode.

Inhaltsverzeichnis

Andere ACME Beleuchtungsausrüstung Handbücher

ACME

ACME BW-54-10FC II RL Bedienungsanleitung

ACME

ACME LED-MTX6S-8W Bedienungsanleitung

ACME

ACME XP-5000WZ Bedienungsanleitung

ACME

ACME Colortec 250 Bedienungsanleitung

ACME

ACME BOOTES Bedienungsanleitung

ACME

ACME DIABOLO 500 Bedienungsanleitung

ACME

ACME PEXEL 100 Bedienungsanleitung

ACME

ACME BRIGHT Bedienungsanleitung

ACME

ACME Diamonds II Bedienungsanleitung

ACME

ACME DOT Bedienungsanleitung

ACME

ACME FESTIVAL Bedienungsanleitung

ACME

ACME LED-SC252 Bedienungsanleitung

ACME

ACME LS-1005 Bedienungsanleitung

ACME

ACME GEIST BSWF Bedienungsanleitung

ACME

ACME COMET Bedienungsanleitung

ACME

ACME Gemini Bedienungsanleitung

ACME

ACME LED-245/2 Bedienungsanleitung

ACME

ACME LED-275 D Bedienungsanleitung

ACME

ACME BF-1500ND B Bedienungsanleitung

ACME

ACME ASTRO LED-256D Bedienungsanleitung

ACME

ACME CP-18TC Bedienungsanleitung

ACME

ACME DAZZLED COLORLED-430 Bedienungsanleitung

ACME

ACME LED-PS10D RGBW Bedienungsanleitung

ACME

ACME Spider FC Bedienungsanleitung

Beliebte Beleuchtungsausrüstung Handbücher anderer Marken

Brizo

Brizo 8SP-MU-4 Bedienungsanleitung

LUCE&LIGHT

LUCE&LIGHT BROM 1.0 Bedienungsanleitung

IKEA

IKEA BJÖRKSPIREA Bedienungsanleitung

Laserworld

Laserworld Evolution Series ES-400RGB Bedienungsanleitung

EuroLite

EuroLite LED B-40 Bedienungsanleitung

Qazqa

Qazqa Suplux SL 3 Black 103062 Bedienungsanleitung

Commercial Electric

Commercial Electric 54568141 Bedienungsanleitung

CREE LIGHTING

CREE LIGHTING 304 Series Bedienungsanleitung

Goobay

Goobay 49867 Bedienungsanleitung

ECOMAN ITALIA

ECOMAN ITALIA LED T8 Bedienungsanleitung

Alkalite

Alkalite Krypton KT-81 Bedienungsanleitung

Clas Ohlson

Clas Ohlson GU10 Bedienungsanleitung

DTS

DTS DELTA 10 F Bedienungsanleitung

ring

ring Solar Steplight Bedienungsanleitung

One Stop Gardens

One Stop Gardens 57696 Montageanleitung

SIREM

SIREM Swimeo A2 Bedienungsanleitung

Silvair

Silvair MESH-CEDRP Bedienungsanleitung

S&P

S&P PCRL80 Bedienungsanleitung