ACME Glamour 350Z Bedienungsanleitung

CONTENTS

1. Safety Instructions ......................................................................................... 2

2. Technical Specifications ................................................................................. 4

3. How To Set The Unit....................................................................................... 5

3.1 Control Panel ........................................................................................... 5

3.2 Main Function.......................................................................................... 6

3.3 Home Position Adjustment .................................................................... 13

4. Control By Universal DMX Controller ........................................................... 14

4.1 DMX512 Connection.............................................................................. 14

4.2 Address Setting ...................................................................................... 15

4.3 DMX512 Configuration........................................................................... 15

5. Troubleshooting........................................................................................... 21

6. Fixture Cleaning ........................................................................................... 22

1. Safety Instructions

WARNING

Please keep this User Guide for future consultation. If you sell the unit to another user, be sure

that they also receive this instruction manual.

Important:

Damages caused by the disregard of this user manual are not subject to warranty. The dealer

will not accept liability for any resulting defects or problems.

Unpack and check carefully that there is no transportation damage before using the unit.

This product is for indoor use only. Use only in a dry location.

DO install and operate by qualified operator.

DO NOT allow children to operate the fixture.

Use safety chain when fixing the unit. Handle the unit by carrying its base instead of head

only.

The unit must be installed in a location with adequate ventilation, at least 50cm from adjacent

surfaces.

Be sure that no ventilation slots are blocked, otherwise the unit will be overheated.

Before operating, ensure that the voltage and frequency of power supply match the power

requirements of the unit.

It’s important to ground the yellow/green conductor to earth in order to avoid electric shock.

Minimum ambient temperature TA: 0℃. Maximum ambient temperature TA: 40℃.

DO NOT connect the device to any dimmer pack.

During initial start-up some smoke or smell may arise. This is a normal process and does not

necessarily mean that the device is defective, and it will decrease gradually within 15 minutes.

Make sure there are no flammable materials close to the unit while operating to avoid fire

hazard.

Examine the power wires carefully; replace them immediately if there is any damage.

Please read the instruction carefully which includes important information about

the installation, usage and maintenance.

Unit’s surface temperature may reach up to 75℃. DO NOT touch the housing bare-handed

during its operation.

Avoid any inflammable liquids, water or metal objects entering the unit. Once it happens, cut

off the mains power immediately.

DO NOT operate in dirty or dusty environment, do clean fixtures regularly.

DO NOT touch any wire during operation as there might be a hazard of electric shock.

Avoid power wires together twist other cables.

The minimum distance between light output and the illuminated surface must be more than

12 meters.

Disconnect mains power before fuse replacement or servicing.

Replace fuse only with the same type.

In the event of serious operating problem, stop using the unit immediately.

Never turn on and off the unit time after time.

The housing, the lenses, or the ultraviolet filter must be replaced if they are visibly damaged.

DO NOT open the unit as there are no user serviceable parts inside.

Never try to repair the unit by yourself. Repairs carried out by unskilled people can lead to

damage or malfunction. Please contact the nearest authorized technical assistance center if

needed.

Disconnect the mains power if the fixture is has not been used for a long time.

DO use the original packing materials before transporting it again.

DO NOT look directly at the light while the LED is on.

DO NOT start on the unit without LED enclosure or when housing is damaged.

Installation:

The fixture should be mounted via its Omega Quick Release Clamp bracket. Always ensure that the

unit is firmly fixed to avoid vibration and slipping while operating and make sure that the structure

to which you are attaching the unit is secure and is able to support a weight of 10 times of the

fixtures weight. Always use a safety cable that can hold 12 times of the weight of the fixture when

installing.

The equipment must be installed by professionals. It must be installed in a place where is out of

the reach of people and no one can pass by or under it.

2. Technical Specifications

Power Voltage:

AC 100~240V, 50/60Hz

Power Consumption:

315W (CM-350Z II)

320W (CM-350Z III)

Light Source:

7x40W RGBW LED

Zoom Range:

5°~50°

Movement:

Pan: 540°

Tilt: 225°

Pan/Tilt Resolution: 16bit

Dimming/Strobe:

0~100% smooth dimming, variable strobe effects

Control:

DMX Channel: 1 1/1 5/14 Channels

Control Mode: DMX, Wireless Control (Optional)

Firmware Upgrade: Update via DMX link

Construction:

Display: LCD Display

Data In/Out: 3-pin&5-pin XLR

Power In/Out: Power Connector in/out

Protection Rating: IP20

Features:

Motorized liner zoom system

Outstanding color macro effect

Fast, quiet, flicker free operation

Dimension/Weight:

310x226x412mm, 10.6kgs

12.2"x8.9"x16.2"in, 23.4lbs

310 mm

412 mm

226 mm

Photometric Diagram:

3. How To Set The Unit

3.1 Control Panel

1. Display: To show the various menus and the selected functions

2. LED:

POWER ON Power On

DMX ON DMX input present

3. Button:

MENU To enter into move backward or leave the menu

DOWN To go forward in the selected functions

UP To go backward in the selected functions

ENTER To confirm the selected functions

4. DMX IN:

DMX512 link, use 3/5-pin XLR cable to link the unit and the DMX controller to input DMX signal

5. DMX OUT:

DMX512 link, use 3/5-pin XLR cable to link the next unit to output DMX signal

6. MAINS IN:

To connect to the mains supply

7. MAIS OUT:

To connect to the next unit

8. Fuse (T 6.3A):

Protects the unit from over-voltage or short circuit

3.2 Main Function

To select any of the given functions, press the MENU button until the required function is showing

on the display. Select the function by pressing the ENTER button and the display will blink. Use the

DOWN/UP buttons to change the mode. Once the required mode has been selected, press the

ENTER button to setup, to go back to the functions without any change press the MENU button

again. Press and hold the MENU button for about one second or wait for one minute to exit the

menu mode.

The main functions are shown overleaf:

DMX Functions

Enter MENU mode, select DMX Functions, press the ENTER button to confirm, use the UP/DOWN

button to select DMX Address, DMX Channel Mode, View DMX Value or WDMX Setting.

DMX Address

To select DMX Address, press the ENTER button to confirm. Use the UP/DOWN button to adjust

the address from 001 to 512, press the ENTER button to setup. Press the MENU button back to the

last menu or let the unit idle one minute to exit menu mode.

DMX Channel Mode

To select DMX Channel Mode, press the ENTER button to confirm. Use the UP/DOWN button to

select Mode1 (11), Mode2 (15) or Mode3 (14), press the ENTER button to setup. Press the MENU

button back to the last menu or let the unit idle one minute to exit menu mode.

View DMX Value

To select View DMX Value, press the ENTER button to confirm. Use the UP/DOWN button to view

the DMX channel values. Press the MENU button back to the last menu or let the unit idle one

minute to exit menu mode.

WDMX Setting

To select WDMX Setting, press the ENTER button to confirm. Use the UP/DOWN button to select

Active, Retransmit, Reset Memory or WDMX Channel, press the ENTER button to setup. Press the

MENU button back to the last menu or let the unit idle one minute to exit menu mode.

Fixture Setting

Enter MENU mode, select Fixture Setting, press the ENTER button to confirm, use the UP/DOWN

button to select Pan Inverse, Tilt Inverse, P/T Feedback,BL.O. P/T Moving, White Balance,

Cooling Mode,Dimmer Curve or Dimmer Speed.

Pan Inverse

To select Pan Inverse, press the ENTER button to confirm. Use the UP/DOWN button to select No

(normal) or Yes (pan inverse), press the ENTER button to setup. Press the MENU button back to

the last menu or let the unit idle one minute to exit menu mode.

Tilt Inverse

To select Tilt Inverse, press the ENTER button to confirm. Use the UP/DOWN button to select No

(normal) or Yes (tilt inverse), press the ENTER button to setup. Press the MENU button back to the

last menu or let the unit idle one minute to exit menu mode.

P/T Feedback

To select P/T Feedback, press the ENTER button to confirm. Use the UP/DOWN button to select

No (Pan or tilt’s position will not feedback while out of step) or Yes (Feedback while pan/tilt out of

step), press the ENTER button to setup. Press the MENU button back to the last menu or let the

unit idle one minute to exit menu mode.

BL.O. P/T Moving

To select BL.O. P/T Moving, press the ENTER button to confirm. Use the UP/DOWN button to

select No (normal while pan/tilt moving) or Yes (blackout while pan/tilt moving), press the ENTER

button to setup. Press the MENU button back to the last menu or let the unit idle one minute to

exit menu mode.

White Balance

To select White Balance, press the ENTER button to confirm. Use the UP/DOWN button to select

Red, Green or Blue, press the ENTER button to setup. Press the MENU button back to the last

menu or let the unit idle one minute to exit menu mode.

Cooling Mode

To select Cooling Mode, press the ENTER button to confirm. Use the UP/DOWN button to select

Auto or Low. Once selected, press the ENTER button to setup. Press the MENU button back to the

last menu or let the unit idle one minute to exit menu mode.

Dimmer Curve

To select Dimmer Curve, press the ENTERbutton to confirm. Use the UP/DOWN button to select

Linear, Square Law, Inverse Squ. or S-Curve. Once selected, press the ENTER button to store.

Press the MENU button back to the last menu or let the unit idle one minute to exit menu mode.

Inhaltsverzeichnis

Andere ACME Beleuchtungsausrüstung Handbücher

ACME

ACME FLASHDOT Bedienungsanleitung

ACME

ACME DELUGE LED-WAV-50W Bedienungsanleitung

ACME

ACME Thunderbreaker Bedienungsanleitung

ACME

ACME Building wash Bedienungsanleitung

ACME

ACME Ozone 3 Bedienungsanleitung

ACME

ACME LP-1600 BD30 Bedienungsanleitung

ACME

ACME FLANDINA 22 IP Bedienungsanleitung

ACME

ACME COOLIE 14FC Bedienungsanleitung

ACME

ACME DIABOLO 500 Bedienungsanleitung

ACME

ACME COMET Bedienungsanleitung

ACME

ACME DAZZLED COLORLED-430 Bedienungsanleitung

ACME

ACME HYGIEA Bedienungsanleitung

ACME

ACME XP-5000WZ Bedienungsanleitung

ACME

ACME FESTIVAL Bedienungsanleitung

ACME

ACME TV LIGHT PANEL 2000 Bedienungsanleitung

ACME

ACME Dynamic 25 Roller LED-SC25B Bedienungsanleitung

ACME

ACME Thunderstruck LP-2304 Bedienungsanleitung

ACME

ACME SABER HYBRID PRO Bedienungsanleitung

ACME

ACME SAMURAI SCAN 50 Bedienungsanleitung

ACME

ACME LED Move 600SE Bedienungsanleitung

ACME

ACME Theatre Spot 150 Bedienungsanleitung

ACME

ACME Spider FC Bedienungsanleitung

ACME

ACME BRIGHT Bedienungsanleitung

ACME

ACME Theatre Spot 150m Bedienungsanleitung

Beliebte Beleuchtungsausrüstung Handbücher anderer Marken

Brizo

Brizo 8SP-MU-4 Bedienungsanleitung

LUCE&LIGHT

LUCE&LIGHT BROM 1.0 Bedienungsanleitung

IKEA

IKEA BJÖRKSPIREA Bedienungsanleitung

Laserworld

Laserworld Evolution Series ES-400RGB Bedienungsanleitung

EuroLite

EuroLite LED B-40 Bedienungsanleitung

Qazqa

Qazqa Suplux SL 3 Black 103062 Bedienungsanleitung

Commercial Electric

Commercial Electric 54568141 Bedienungsanleitung

CREE LIGHTING

CREE LIGHTING 304 Series Bedienungsanleitung

Goobay

Goobay 49867 Bedienungsanleitung

ECOMAN ITALIA

ECOMAN ITALIA LED T8 Bedienungsanleitung

Alkalite

Alkalite Krypton KT-81 Bedienungsanleitung

Clas Ohlson

Clas Ohlson GU10 Bedienungsanleitung

DTS

DTS DELTA 10 F Bedienungsanleitung

ring

ring Solar Steplight Bedienungsanleitung

One Stop Gardens

One Stop Gardens 57696 Montageanleitung

SIREM

SIREM Swimeo A2 Bedienungsanleitung

Silvair

Silvair MESH-CEDRP Bedienungsanleitung

S&P

S&P PCRL80 Bedienungsanleitung