ACME LED-MTX6S-8W Bedienungsanleitung

LED-MTX6S-8W

UserManual

Please read the instruction carefully before use

CONTENTS

1. Safety Instructions....................................................................................................2

2. Technical Specifications............................................................................................3

3. How To Set The Unit .................................................................................................4

3.1 Control Panel ......................................................................................................4

3.2 Main Function ....................................................................................................5

3.3 Home Position Adjustment.............................................................................. 10

4. How to Control the Unit ........................................................................................ 11

4.1 Master/Slave Built In Preprogrammed Function ............................................. 11

4.2 Easy CA-8 Controller ........................................................................................ 11

4.3 DMX Controller................................................................................................ 12

5. DMX 512 Configuration ......................................................................................... 13

6. DMX Connection ................................................................................................... 15

7. Troubleshooting..................................................................................................... 16

8. Fixture Cleaning......................................................................................................17

1. Safety Instructions

WARNING

Please keep this User Manual for future consultation. If you sell the unit to another user, be sure

that they also receive this instruction booklet.

Unpack and check carefully there is no transportation damage before using the unit.

Before operating, ensure that the voltage and frequency of power supply match the power

requirements of the unit.

It’s important to ground the yellow/green conductor to earth in order to avoid electric shock.

The unit is for indoor use only. Use only in a dry location.

The unit must be installed in a location with adequate ventilation, at least 50cm from adjacent

surfaces. Be sure that no ventilation slots are blocked.

Disconnect main power before replacement or servicing.

Make sure there are no flammable materials close to the unit while operating as it is fire hazard.

Use safety cables when fixing this unit.

Maximum ambient temperature is Ta: 40 degrees C. DO NOT operate it where the temperature

is higher than this.

In the event of a serious operating problem, stop using the unit immediately. Never try to repair

the unit by yourself. Repairs carried out by unskilled people can lead to damage or malfunction.

Please contact the nearest authorized technical assistance center. Always use the same type

spare parts.

DO NOT touch any cables during operation as high voltage may cause electric shock.

Warning:

To prevent or reduce the risk of electrical shock or fire, do not expose the unit to rain or

moisture.

The housing and lenses must be replaced if they are visibly damaged.

Please read the instructions carefully which includes important information

about the installation, operation and maintenance.

Caution:

There are no user serviceable parts inside the unit. Do not open the housing or attempt any

repairs yourself. In the unlikely event your unit may require service, please contact your nearest

dealer.

Installation:

The unit should be mounted via its screw holes on the bracket. Always ensure that the unit is

firmly fixed to avoid vibration and slipping while operating. Make sure that the structure to which

you are attaching the unit is secure and is able to support a weight of 10 times of the unit’s

weight. Also always use a safety cable that can hold 12 times of the weight of the unit when

installing the fixture.

The equipment must be installed by professionals. It must be fixed at a place where is out of the

reach of people and no one pass by or under it.

2. Technical Specifications

◇6 x 8W high power LED creating a powerful, scanning beam effect

◇Electronic strobe with pulse and random effects

◇High efficiency and low power consumption

Power Voltage: AC 100-240V, 50/60Hz

Power Consumption: 64.5W

Power Cable Daisy Chains: 9 Fixtures Max. (230V, 50Hz)

5FixturesMax.(120V,60Hz)

Fuse: T6.3A

LED Sources: 6x8WWhiteLEDs

Dimension: 843x84x170mm

Weight: 5.5kgs

3. How To Set The Unit

3.1 Control Panel

1. POWER IN: Connects to power supply

2. POWER OUT: Connects to next fixture

3. Function Display: Shows the various menus and the selected function

LED:

4. DMX On DMX input present

5. MASTER On Master Mode

6. SLAVE On Slave Mode

7. SOUND Flashing Sound activation

8. Button:

MENU To select the programming functions

DOWN To go backward in the selected functions

UP To go forward in the selected functions

ENTER To confirm the selected functions

9. Microphone: Receives music signals for sound active mode

10.Only for remote control: Connects with the optional CA-8 to control the unit

11. DMX IN: DMX 512 link, use 3-pin XLR cable to link the unit and the DMX controller

12. DMX OUT: DMX 512 link, use 3-pin XLR cable to link the next unit and output the DMX signal

3.2 Main Function

To select any of the given functions, press the MENU button up to the required selection as shown

on the display. Select the function by pressing the ENTER button and the display will blink. Use the

DOWN/UP buttons to change the mode. Once the required mode has been selected, press the

ENTER button to confirm. To go back to the main function without any change press the MENU

button again. Press and hold the MENU button for about one second or wait for 7 seconds to exit

the current mode.

The main functions are shown below:

DMX 512 ADDRESS

To select , press the ENTER button to show DMX ADDRESS on the display. Use the DOWN

/UP buttons to adjust the address from 1 to 512. Once the address has been selected, press the

ENTER button to setup. To go back to the functions without any changes press the MENU button

again. Press and hold the MENU button for about one second or wait for 7 seconds to exit the

menu mode.

SLAVE MODE

To select , press the ENTER button to show SLAVE MODE on the display. Use the

DOWN/UP buttons to select (normal) or (2 light show) mode. Once selected, press

the ENTER button to setup. To go back to the functions without any changes press the MENU

button again. Press and hold the MENU button for about one second or wait for 7 seconds to exit

the menu mode.

CHANNEL MODE

To select , press the ENTER button to show CHANNEL MODE on the display. Use the

DOWN/UP button to select 1, 4, 9or 11 channel modes. Once the mode has been selected, press

the ENTER button to setup. To go back to the functions without any changes press the MENU

button again. Press and hold the MENU button for about one second or wait for 7 seconds to exit

the menu mode.

ANGLE SETTING

To select , press the ENTER button to show ANGLE SETTING on the display. Use the

DOWN/UP button to select the 150°, 120°or 90° mode.Once the angle has been selected, press

the ENTER button to setup. To go back to the functions without any changes press the MENU

button again. Press and hold the MENU button for about one second or wait for 7 seconds to exit

the menu mode.

SHOW MODE

To select , press the ENTER button to show SHOW MODE on the display. Use the

DOWN/UP buttons to select (Show 0, random show) or (Show 1) or (Show

2) or … or (Show 12). Once the show has been selected, press the ENTER button to setup.

To go back to the functions without any changes press the MENU button again. Press and hold the

MENU button for about one second or wait for 7 seconds to exit the menu mode.

SOUND MODE

To select , press the ENTER button to show SOUND MODE on the display. Use the

DOWN/UP buttons to select (sound on) or (sound off). Once selected, press the

ENTER button to setup. To go back to the functions without any changes press the MENU button

again. Press and hold the MENU button for about one second or wait for one minute to exit the

menu mode.

BLACKOUT MODE

To select , press the ENTER button to show BLACKOUT MODE on the display. Use the

DOWN/UP buttons to select (blackout) or (normal) mode. Once the mode has

been selected, press the ENTER button to setup. To go back to the functions without any changes

press the MENU button again. Press and hold the MENU button for about one second or wait for 7

seconds to exit the current mode.

LED DISPLAY

To select , press the ENTER button to show LED DISPLAY on the display. Use the DOWN/UP

button to select (LED on) or (LED off) mode. Once the mode has been selected,

press the ENTER buttons to setup. To go back to the functions without any changes press the

MENU button again. Press and hold the MENU button for about one second or wait for 7 seconds

to exit the current mode.

DISPLAY INVERSE

To select , press the ENTER button to show DISPLAY on the display, and press the ENTER

button again, it will show the (inversion). To go back to the functions without any changes

press the MENU button.

TILT INVERSION

To select , press the ENTER button to show the TILT on the display. Use the DOWN/UP

buttons to select (activate tilt inversion) or (Normal, deactivate tilt inversion).

Once the mode has been selected, press the ENTER button to setup. To go back to the functions

without any changes press the MENU button again. Press and hold the MENU button for about

one second or wait for 7 seconds to exit the menu mode.

LED INVERSION

To select , press the ENTER button to show REVERSION on the display. Use the DOWN/UP

buttons to select (the leds will light up from right to left) or (Normal, the leds

will light up from left to right). Once the mode has been selected, press the ENTER button to setup.

To go back to the functions without any changes press the MENU button again. Press and hold the

MENU button for about one second or wait for 7 seconds to exit the menu mode.

AUTO TEST

To select , press the ENTER button to show TEST on the display and the unit will run a

self-test . To go back to the functions without any changes press the MENU button again. Press

and hold the MENU button for about one second or wait for 7 seconds to exit the current mode.

TEMPERATURE

To select , press the ENTER button to show the TEMPERATURE on the display and the

display will show the temperature of the unit. To go back to the functions without any changes

Inhaltsverzeichnis

Andere ACME Beleuchtungsausrüstung Handbücher

ACME

ACME Dragon Scan 50 LED-SC50B Bedienungsanleitung

ACME

ACME Thunderroar Bedienungsanleitung

ACME

ACME Spartan Hybrid C Bedienungsanleitung

ACME

ACME Inferno Bedienungsanleitung

ACME

ACME LED STROBE 50 Bedienungsanleitung

ACME

ACME COMET Bedienungsanleitung

ACME

ACME LED-MS600 PE Bedienungsanleitung

ACME

ACME Colortec 250 Bedienungsanleitung

ACME

ACME BW-54-10FC II RL Bedienungsanleitung

ACME

ACME LED-PS10D RGBW Bedienungsanleitung

ACME

ACME Pageant CM-200Z Bedienungsanleitung

ACME

ACME CA-DC6S Bedienungsanleitung

ACME

ACME Gemini Bedienungsanleitung

ACME

ACME GLAMOUR 700Z RGBY Bedienungsanleitung

ACME

ACME LP-1600 BD30 Bedienungsanleitung

ACME

ACME VOGUE Bedienungsanleitung

ACME

ACME LED-SC25 Bedienungsanleitung

ACME

ACME Xperior 1500SZ Bedienungsanleitung

ACME

ACME BRIGHT Bedienungsanleitung

ACME

ACME DIABOLO 500 Bedienungsanleitung

ACME

ACME LED-835B Bedienungsanleitung

ACME

ACME RAYZOR HYBRID Bedienungsanleitung

ACME

ACME COOLIE 14FC Bedienungsanleitung

ACME

ACME FLASHDOT Bedienungsanleitung

Beliebte Beleuchtungsausrüstung Handbücher anderer Marken

Brizo

Brizo 8SP-MU-4 Bedienungsanleitung

LUCE&LIGHT

LUCE&LIGHT BROM 1.0 Bedienungsanleitung

IKEA

IKEA BJÖRKSPIREA Bedienungsanleitung

Laserworld

Laserworld Evolution Series ES-400RGB Bedienungsanleitung

EuroLite

EuroLite LED B-40 Bedienungsanleitung

Qazqa

Qazqa Suplux SL 3 Black 103062 Bedienungsanleitung

Commercial Electric

Commercial Electric 54568141 Bedienungsanleitung

CREE LIGHTING

CREE LIGHTING 304 Series Bedienungsanleitung

Goobay

Goobay 49867 Bedienungsanleitung

ECOMAN ITALIA

ECOMAN ITALIA LED T8 Bedienungsanleitung

Alkalite

Alkalite Krypton KT-81 Bedienungsanleitung

Clas Ohlson

Clas Ohlson GU10 Bedienungsanleitung

DTS

DTS DELTA 10 F Bedienungsanleitung

ring

ring Solar Steplight Bedienungsanleitung

One Stop Gardens

One Stop Gardens 57696 Montageanleitung

SIREM

SIREM Swimeo A2 Bedienungsanleitung

Silvair

Silvair MESH-CEDRP Bedienungsanleitung

S&P

S&P PCRL80 Bedienungsanleitung