ACME BF-1500ND B Bedienungsanleitung

BF-1500ND B

BF-750ND B

BF-1500ND B

BF-750ND B

User Guide

Professional Entertainment Technology

TABLE OF CONTENTS

1. Introduction

2. Safety Precaution

3. Technical Specifications

4. General Functions

5. How To Change The Lamp

6. How To Control the Unit

A. By Master/Slave Built In Preprogrammed Function

B. By Easy Controller

C. By universal DMX Controller

7. DMX512 Configuration

8. DMX512 Connection

9. Troubleshooting

10. Fixture Cleaning

1. Introduction

Congratulations on the purchase of your new strobe light. We are confident you will

enjoy many trouble free hours with this unit. To assist with the care and use of the

product we have prepared this short guide.

2. Safety Precaution

• Avoid direct eye exposure.

• Disconnect from mains power before replacing lamp or servicing.

• Always replace the lamp with same type.

•To prevent fire or shock hazard, do not expose this unit to rain or

moisture.

•Do not use this product continuously longer than 15 minutes under

maximum speed and dimmer.

The following points are important for safety as well as for the smooth installation

and performance of the unit.

•Unpack carefully and be sure that no damage has occurred during transportation.

•It is very important to ground the yellow/green conductor in order to meet safety

regulations.

•Do not connect the device to any dimmer pack.

•The electrical work that is necessary for installation must be done by qualified

personnel.

•Be sure to locate the unit in a place with adequate ventilation at least 15 cm from

the walls. Be sure that no ventilation slots are blocked.

•Be careful that no liquids or other objects can enter into the unit. If this ever

happens, disconnect the main power immediately.

•In the event of serious operating problems, turn off the power immediately. Never

try to repair the unit by yourself. Repairs carried out by non-qualified personnel

can lead to serious damage or malfunction. Please contact your dealer for

technical assistance. Always use genuine spare parts.

•Always remember to unplug the unit from the mains power before any service is

done.

Installation

The unit should be mounted via its screw holes on the bracket. Always ensure

that the unit is firmly fixed to avoid vibration and slipping while operating. Make

sure that the bracer can support the weight more than 10 times of the unit. And

use safety chain which can hold over 12 times weight of the unit when you fix the

equipment.

The equipment must be fixed by professionals. And it must be fixed at a place

where is out of the touch of human and has no one pass by or sit down.

3. Technical Specifications

Lamp

XENON 1500W

XENON 750W

Power

AC 230V 50Hz

AC 230V- 50Hz/120V-60Hz

Fuse

Circuit breaker 20A

Circuit breaker 15A

Dimensions

452 x 147.5 x 116 mm

307 x 147.5 x 116 mm

Weight

3.2 kg

2.7 kg

4. General Functions

1. POWER INPUT: AC 230V 50Hz (BF-1500ND B)

AC 230V- 50Hz/120V-60Hz (BF-750ND B)

2. FUSE: 20A/15A

3. DMX IN: XLR male socket, use to receive DMX signals.

4. DMX OUT: XLR female socket, use to transmit DMX signals.

5. Remote controller input: By connecting to the 1/4 “microphone jack to control

the unit for Stand by, Function and Mode.

6. DMX DIP SWITCH: Dip switch 1-9 are used to set DMX address of the unit.

Assign dip switch 1 ON, this unit is in master mode, assign dip switch 1 and 10

ON at the same time to adjust dimmer and strobe speed.

7. DIMMER: This knob used to adjust brightness of the units.

8. SPEED: This knob used to adjust the speed of Strobe.

5. How To Change The Lamp

• Always switch off the main supply and never handle the lamp or luminaire when it

is hot.

• Do not touch the bulb with bare hands. If this does happen, clean the lamp with

denatured alcohol and wipe with a lint free cloth before installing.

• Remember always replace the lamp with the same type lamp.

1. Loose the screws on the

metal base at bottom.

2. Open the glass base-cover.

3. Loose the screws of the lamp

wire from terminator.

5. Connect the lamp wire to

the terminator.

6. Reverse the procedures

from step 2 to step 1.

4. Take out the old lamp and

replace the new one to the

fixture.

6. How To Control the Unit

You can operate the unit in three ways:

A. By Master/slave Built-in Preprogrammed Function

By linking the units in master/slave connection, the first unit will control the other

units to give an automatic light show. You will know which unit is the master

because its DMX input jack will have nothing plugged into it. The other units

(slaves) will have DMX cables plugged into the DMX input jacks (daisy chain).

You can set the units in below two ways:

1. Synchronized show: set the first unit（master）dipswitch 1 and 10 to be ON at

the same time, so you can adjust the dimmer and

strobe speed, and all the other (slave) units will

run as same as the first (master) unit.

2. 4-Light show: set the dipswitch as the diagram,

the first (master) unit will run the built-in

programmer and control the other (slave) units for

4-light show.

Chase pattern in 4-light show mode:

Pattern 1

1234 Full on

Pattern 2

1-2-3-4 ―4-3-2-1

Pattern 3

1-2-3-4-4-3-2-1

Pattern 4

12-34 ―23-14

Pattern 5

1-12-123-1234-123-12-1-stop ―4-43-432-4321-432-43-4-stop

Pattern 6

1-2-1-2-3-4-3-4―4-1-4-1-3-2-3-2

B. By Easy Controller

The easy remote control is used only in master/slave mode. By

connecting to the 1/4” microphone jack of the first unit, you will find that

the remote control on the first unit will control all the other units for Stand

by, Function and Mode.

-- STAND BY : stand by and blackout all the unit.

-- FUNCTION :

• Under Audio status ( LED light off ), hold on the button, all the units

will strobe quickly.

• Under Manual status ( LED light on ), press the button for choosing next pattern, triggered

by music.

• Under Auto status ( LED light blinking ), press the button briefly to choose the patterns ( 6

patterns varied with different speeds: fast, normal, or slow ). Hold on the button to choose

the 6 patterns varied with 3 different brightness.

-- MODE:

• AUDIO status ( LED light off ): All patterns triggered by music.

• MANUAL status ( LED light on ): Press button Function to choose the next pattern

triggered by music.

• AUTO status ( LED light blinking ): Press button Function briefly for speed selection; hold

on the Function button for brightness selection.

C. By universal DMX controller

If you use a universal DMX controller to control the units, you have to set dip switches from 1

to 9 of the channel so that all the units will receive its DMX signal. Please refer to the

following diagram to know how to address your DMX512 system in the binary code.

DMX512 Address Chart

Dip

#10

Value

128

256

Option

•

Examples:

Channel 1 : dip / on : #1 ( =1 )

Channel 3 : dip / on : #1, #2 ( 1 + 2 = 3)

Channel 5 : dip / on : #1, #3 ( 1 + 4 = 5 )

Channel 7 : dip / on : #1, #2, #3 ( 1 + 2 + 4 = 7 )

7. DMX512 Configuration

DMX512 configuration

DMX512

Level rang 0~255

Channel 1

Channel 2

Strobe Speed

Dimmer

240~255

Speed 15

Dimmer 15

224~239

Speed 14

Dimmer 14

208~223

Speed 13

Dimmer 13

192~207

Speed 12

Dimmer 12

176~191

Speed 11

Dimmer 11

160~175

Speed 10

Dimmer 10

144~159

Speed 9

Dimmer 9

128~143

Speed 8

Dimmer 8

112~127

Speed 7

Dimmer 7

96~111

Speed 6

Dimmer 6

80~95

Speed 5

Dimmer 5

64~79

Speed 4

Dimmer 4

48~63

Speed 3

Dimmer 3

32~47

Speed 2

Dimmer 2

16~31

Speed 1

Dimmer 1

0~15

Stopped

Blackout

8. DMX512 Connection

The DMX512 is widely used in intelligent lighting control, with a maximum of 512

channels.

1. If you using a controller with 5 pins DMX output, you need to use a 5 to 3 pin

adapter-cable.

2. At last unit, the DMX cable has to be terminated with a terminator. Solder a

120 ohm 1/4W resistor between pin 2(DMX-) and pin 3(DMX+) into a 3-pin

XLR-plug and plug it in the DMX-output of the last unit.

3. Connect the unit together in a ‘daisy chain’ by XLR plug from the output of the

unit to the input of the next unit. The cable can not be branched or split to a ‘Y’

cable. DMX512 is a very high-speed signal. Inadequate or damaged cables,

solder joints or corroded connectors can easily distort the signal and shut

down the system.

4. The DMX output and input connectors are pass-through to maintain the DMX

circuit, when power is disconnected to the unit.

5. Each lighting unit needs to have an address set to receive the data sent by the

controller. The address number is between 0-511 (usually 0 & 1 are equal to

1).

6. The end of the DMX512 system should be terminated to reduce signal errors.

7. 3 pin XLR connectors are more popular than 5 pin XLR.

3 pin XLR: Pin 1: GND, Pin 2: Negative signal (-), Pin 3: Positive signal (+)

5 pin XLR: Pin 1: GND, Pin 2: Negative signal (-), Pin 3: Positive signal (+)

9. Troubleshooting

• If the unit is not functioning well –check main power supply is ‘on’ and check

fuses.

• If the unit is functioning but lamp does not light - may require replacing lamp.

• If the unit is not moving to the music, check the sound-activation adjustment

(when applicable)

•After trying these solutions, you still have a problem, contact your dealer for

technical assistance.

•The unit has built-in thermal switch. The lamp will not work when the internal

temperature is above 80℃, and the lamp will work again when the internal

temperature is cool down.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere ACME Beleuchtungsausrüstung Handbücher

ACME

ACME COMET Bedienungsanleitung

ACME

ACME Dynamic 25 Spin LED?GF25 Bedienungsanleitung

ACME

ACME Thunderbreaker Bedienungsanleitung

ACME

ACME Theatre Spot 150 Bedienungsanleitung

ACME

ACME Xperior 1500SZ Bedienungsanleitung

ACME

ACME Diamonds II Bedienungsanleitung

ACME

ACME GLORV FRAMING XP-5000SZF Bedienungsanleitung

ACME

ACME MP-12FC Bedienungsanleitung

ACME

ACME LED Move 600SE Bedienungsanleitung

ACME

ACME ENERGY SPOT XA-400 SPOT Bedienungsanleitung

ACME

ACME Dynamic 25 Roller LED-SC25B Bedienungsanleitung

ACME

ACME Theatre Spot 150m Bedienungsanleitung

ACME

ACME Stage Par 220MP-220 Bedienungsanleitung

ACME

ACME Libre Bedienungsanleitung

ACME

ACME LED-SC252 Bedienungsanleitung

ACME

ACME V Inground VI-10QW Bedienungsanleitung

ACME

ACME GEIST BSWF Bedienungsanleitung

ACME

ACME V-BOX Bedienungsanleitung

ACME

ACME TV LIGHT PANEL 2000 Bedienungsanleitung

ACME

ACME Sunrise Bedienungsanleitung

ACME

ACME IL-2420 II Bedienungsanleitung

ACME

ACME FESTIVAL Bedienungsanleitung

ACME

ACME Solar Flare Bedienungsanleitung

ACME

ACME IM-250 SP Bedienungsanleitung

Beliebte Beleuchtungsausrüstung Handbücher anderer Marken

Brizo

Brizo 8SP-MU-4 Bedienungsanleitung

LUCE&LIGHT

LUCE&LIGHT BROM 1.0 Bedienungsanleitung

IKEA

IKEA BJÖRKSPIREA Bedienungsanleitung

Laserworld

Laserworld Evolution Series ES-400RGB Bedienungsanleitung

EuroLite

EuroLite LED B-40 Bedienungsanleitung

Qazqa

Qazqa Suplux SL 3 Black 103062 Bedienungsanleitung

Commercial Electric

Commercial Electric 54568141 Bedienungsanleitung

CREE LIGHTING

CREE LIGHTING 304 Series Bedienungsanleitung

Goobay

Goobay 49867 Bedienungsanleitung

ECOMAN ITALIA

ECOMAN ITALIA LED T8 Bedienungsanleitung

Alkalite

Alkalite Krypton KT-81 Bedienungsanleitung

Clas Ohlson

Clas Ohlson GU10 Bedienungsanleitung

DTS

DTS DELTA 10 F Bedienungsanleitung

ring

ring Solar Steplight Bedienungsanleitung

One Stop Gardens

One Stop Gardens 57696 Montageanleitung

SIREM

SIREM Swimeo A2 Bedienungsanleitung

Silvair

Silvair MESH-CEDRP Bedienungsanleitung

S&P

S&P PCRL80 Bedienungsanleitung