Aeotec MultiSensor 7 Bedienungsanleitung

https://manual.zwave.eu/backend/make.php?lang=en&sku=AEOEZWA024&cert=ZC12-20120147 1/37

Aeotec

MultiSensor 7

SKU: AEOEZWA024

Quickstart

This is a secure Alarm Sensor for Europe. To run this device please insert fresh 2 * CR123A batteries. Please make sure the internal battery is fully

charged.

your

supports

you

ult

nsor

utom

ica

lly

nsor

your

supports

Important safety information

Please read this manual carefully. Failure to follow the recommendations in this manual may be dangerous or may violate the law. The manufacturer, importer,

distributor and seller shall not be liable for any loss or damage resulting from failure to comply with the instructions in this manual or any other material. Use this

equipment only for its intended purpose. Follow the disposal instructions. Do not dispose of electronic equipment or batteries in a ﬁre or near open heat sources.

What is Z-Wave?

24/11/2022, 15:52 https://manual.zwave.eu/backend/make.php?lang=en&sku=AEOEZWA024&cert=ZC12-20120147

https://manual.zwave.eu/backend/make.php?lang=en&sku=AEOEZWA024&cert=ZC12-20120147 2/37

Z-Wave is the international wireless protocol for communication in the Smart Home. This device is suited for use in the region mentioned in the Quickstart section.

Z-Wave ensures a reliable communication by reconﬁrming every message (two-way communication) and

every mains powered node can act as a repeater for other nodes (meshed network) in case the receiver is

not in direct wireless range of the transmitter.

This device and every other certiﬁed Z-Wave device can be used together with any other certiﬁed Z-

Wave device regardless of brand and origin as long as both are suited for the same frequency range.

If a device supports secure communication it will communicate with other devices secure as long as this

device provides the same or a higher level of security. Otherwise it will automatically turn into a lower level

of security to maintain backward compatibility.

For more information about Z-Wave technology, devices, white papers etc. please refer to www.z-wave.info.

Product Description

ult

nsor

lop

bie

mov

nsm



lus

pow

G



ech

nolo

out

mor

out

M

ult

nsor



ollow

Prepare for Installation / Reset

Please read the user manual before installing the product.

In order to include (add) a Z-Wave device to a network it must be in factory default state. Please make sure to reset the device into factory default. You can do

this by performing an Exclusion operation as described below in the manual. Every Z-Wave controller is able to perform this operation however it is recommended

to use the primary controller of the previous network to make sure the very device is excluded properly from this network.

Reset to factory default

This device also allows to be reset without any involvement of a Z-Wave controller. This procedure should only be used when the primary controller is inoperable.

Press and hold the button for 20 seconds. When the red led ﬂashes, the device will enter the factory reset mode.

Safety Warning for Batteries

The product contains batteries. Please remove the batteries when the device is not used. Do not mix batteries of different charging level or different brands.

Installation

pow

typ

you

ult

nsor

ice

pow

ice

ake

sur

you

your

efe

pow

typ

bef

you



24/11/2022, 15:52 https://manual.zwave.eu/backend/make.php?lang=en&sku=AEOEZWA024&cert=ZC12-20120147

https://manual.zwave.eu/backend/make.php?lang=en&sku=AEOEZWA024&cert=ZC12-20120147 3/37

A

you

cha

nput

pow

typ

(

pow

you

oul

your

only

rst

ice

upon

rst

nto

your

ontroll

pow

nst

(

pow

mov

idi

nlo

utton

LEF

pull

prov

ided

cab

nto

your

nsor

‘

port

cab

nto

omput

ada

hich

edia

pow

your

ult

nsor



ake

sur

back

onto

ult

nsor

idi

nlo

utton

RIGH

pow

nst

(

ice

pow

mov

idi

nlo

utton

LEF

pull

24/11/2022, 15:52 https://manual.zwave.eu/backend/make.php?lang=en&sku=AEOEZWA024&cert=ZC12-20120147

https://manual.zwave.eu/backend/make.php?lang=en&sku=AEOEZWA024&cert=ZC12-20120147 4/37

two

123

acc

diag

your

nsor



ult

nsor

pow

123

(

‘

hich

port

cha

mor

ntly

(

ife



ARNING

N

omp

echa

geab

123

(3.6

ake

sur

back

onto

ult

nsor

idi

nlo

utton

RIGH

24/11/2022, 15:52 https://manual.zwave.eu/backend/make.php?lang=en&sku=AEOEZWA024&cert=ZC12-20120147

https://manual.zwave.eu/backend/make.php?lang=en&sku=AEOEZWA024&cert=ZC12-20120147 5/37

To install your TriSensor with the Back-Mount Plate;

1. You can afﬁx the Back-Mount Arm by Double-Sided Tape or using the provided KA2.5ƒ-20 mm screws.

Tips: We suggest you choose the second method (using screws to afﬁx the Back-Mount Arm) which would be more stable.

2. After you have completed the afﬁxing of Back-Mount Arm, you will need to lock TriSensor to the Back-Mount Arm by screwing TriSensor in.

24/11/2022, 15:52 https://manual.zwave.eu/backend/make.php?lang=en&sku=AEOEZWA024&cert=ZC12-20120147

https://manual.zwave.eu/backend/make.php?lang=en&sku=AEOEZWA024&cert=ZC12-20120147 6/37

3. The Back-Mount Arm may be locked at various angles by turning the Friction Lock clockwise and counter-clockwise to respectively tighten or loosen the angle of

the arm. You can rotate the Friction Lock to change the measurement area of sensor.

24/11/2022, 15:52 https://manual.zwave.eu/backend/make.php?lang=en&sku=AEOEZWA024&cert=ZC12-20120147

https://manual.zwave.eu/backend/make.php?lang=en&sku=AEOEZWA024&cert=ZC12-20120147 7/37

Inclusion/Exclusion

On factory default the device does not belong to any Z-Wave network. The device needs to be added to an existing wireless network to communicate with the

devices of this network. This process is called Inclusion.

Devices can also be removed from a network. This process is called Exclusion. Both processes are initiated by the primary controller of the Z-Wave network. This

controller is turned into exclusion respective inclusion mode. Inclusion and Exclusion is then performed doing a special manual action right on the device.

Inclusion

1. Open the Cover

2. Insert the battery or connect the USB cable

3. Press the button once

4. If prompted, enter the 5 digit DSK code.

Exclusion

1. Open the Cover

2. Press the button once

Product Usage

Button Functions.



24/11/2022, 15:52 https://manual.zwave.eu/backend/make.php?lang=en&sku=AEOEZWA024&cert=ZC12-20120147

https://manual.zwave.eu/backend/make.php?lang=en&sku=AEOEZWA024&cert=ZC12-20120147 8/37

Action button press LED Status Function

1x Tap (when factory reset) SolidYellow Pair Mode

Enters Z-Wave pair mode, ﬂashes white/green 4 times

within 2 seconds upon success.

1x Tap (when already paired) SolidPurple Sends NIF / Excludes device

if Z-Wave controller is in unpair mode, startsblueLED fade

in/out if unpaired and factory reset successfully.

Press and hold [1, 2 seconds) No LED N/A

Press and hold [2, 5 seconds) SolidRed Quick Wakeup

LED will disappear as soon as you release its button. The

MultiSensor 7 will send a wakeup report to your Z-Wave

Controller to take in any queued z-wave commands waiting

in your controller.

Press and hold [5, 9 seconds) SolidOrange Long Wakeup Mode

LED will remain solidOrangeupon release of its button for 5

minutes maximum (or until told to sleep by user or z-wave

controller). This will allow you to easily conﬁgure this device

while the sensor is used with battery power assuming your

Z-Wave controller does not queue the command.

Press and hold [9, 15

seconds)

SolidCyan Communication Health Test(Direct gateway

communication - does not test through repeaters).

This will test your MultiSensor 7 direct communication to

your Z-Wave Controller. It will remainCyanwhile it is

testing.

Once ﬁnished it will become a solid color for 2 seconds

asred,yellow, orgreento indicate health:

Red= Bad health, can‘t communicate at all.

Yellow= Moderate health, could use improvement, some

24/11/2022, 15:52 https://manual.zwave.eu/backend/make.php?lang=en&sku=AEOEZWA024&cert=ZC12-20120147

https://manual.zwave.eu/backend/make.php?lang=en&sku=AEOEZWA024&cert=ZC12-20120147 9/37

communcation missed.

Green= Great health

Press and hold [15, 20

seconds)

BlinkingRed Release here to cancel Factory Reset.

Press and hold [20+ seconds) Bluefade in/out for

2 seconds.

Factory Reset.



Communication to a Sleeping device (Wakeup)

This device is battery operated and turned into deep sleep state most of the time to save battery life time. Communication with the device is limited. In order to

communicate with the device, a static controller C is needed in the network. This controller will maintain a mailbox for the battery operated devices and store

commands that can not be received during deep sleep state. Without such a controller, communication may become impossible and/or the battery life time is

signiﬁcantly decreased.

This device will wakeup regularly and announce the wakeup state by sending out a so called Wakeup Notiﬁcation. The controller can then empty the mailbox.

Therefore, the device needs to be conﬁgured with the desired wakeup interval and the node ID of the controller. If the device was included by a static controller this

controller will usually perform all necessary conﬁgurations. The wakeup interval is a tradeoff between maximal battery life time and the desired responses of the

device. To wakeup the device please perform the following action:

Waking up MultiSensor 7.



In order to conﬁgure Multisensor 7, you must either (1) wake up Multisensor 7 using the below button press function, or (2) temporarily put your Multisensor 7 on

USB power.



This section will go over the manual wakeup of this sensor in case you don‘t want to wait for conﬁguration.



Quick Wakeup.



ult

nsor

utton

unt

LED

turns

nto

R

C

olor

)

ult

nsor

utton

LED

oul

turn

igh

omm

your

ontroll



24/11/2022, 15:52 https://manual.zwave.eu/backend/make.php?lang=en&sku=AEOEZWA024&cert=ZC12-20120147

https://manual.zwave.eu/backend/make.php?lang=en&sku=AEOEZWA024&cert=ZC12-20120147 10/37



Long Wakeup.



1. Press and hold Multisensor 7 Action button



2. Wait until the LED turns into a solid



color (2 - 5 seconds)



3. Release Multisensor 7 Action Button, the LED should remain solidorangewhile it is awake. Send any conﬁgurations from your hub (assuming the

commands are not queued).



If the MultiSensor 7 LEDorangeLED turns off right away, this would indicate that your hub is putting your device to sleep. Try un-powering your hub

temporarily, follow steps 1-3 again, then power up your hub again.



4. Tap the Action Button on Multisensor 7 to put Multisensor 7 back to sleep, or wait 5 minutes. (recommended to manually put it back to sleep to conserve

battery life).



Quick trouble shooting

Here are a few hints for network installation if things dont work as expected.

1. Make sure a device is in factory reset state before including. In doubt exclude before include.

2. If inclusion still fails, check if both devices use the same frequency.

3. Remove all dead devices from associations. Otherwise you will see severe delays.

4. Never use sleeping battery devices without a central controller.

5. Dont poll FLIRS devices.

6. Make sure to have enough mains powered device to beneﬁt from the meshing

Association - one device controls an other device

Z-Wave devices control other Z-Wave devices. The relationship between one device controlling another device is called association. In order to control a different

device, the controlling device needs to maintain a list of devices that will receive controlling commands. These lists are called association groups and they are

always related to certain events (e.g. button pressed, sensor triggers, ...). In case the event happens all devices stored in the respective association group will

receive the same wireless command wireless command, typically a 'Basic Set' Command.

Association Groups:

Andere Handbücher für MultiSensor 7

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Aeotec Zubehör Handbücher

Aeotec

Aeotec MULTISENSOR 6 Bedienungsanleitung

Aeotec

Aeotec Siren 6 Bedienungsanleitung

Aeotec

Aeotec AEO ZWA008-C Bedienungsanleitung

Aeotec

Aeotec Water Sensor 7 Pro Bedienungsanleitung

Aeotec

Aeotec AEOEZW112 Bedienungsanleitung

Aeotec

Aeotec Smart Switch 7 ZWA023 Bedienungsanleitung

Aeotec

Aeotec TriSensor Bedienungsanleitung

Aeotec

Aeotec MULTISENSOR 6 Bedienungsanleitung

Aeotec

Aeotec DSB05106-ZWUS Bedienungsanleitung

Aeotec

Aeotec ZWA005 Bedienungsanleitung

Aeotec

Aeotec TriSensor ZWA005 Bedienungsanleitung

Aeotec

Aeotec MultiSensor Bedienungsanleitung

Aeotec

Aeotec ZW187 Bedienungsanleitung

Aeotec

Aeotec MULTISENSOR 6 Bedienungsanleitung

Aeotec

Aeotec ZW089 Bedienungsanleitung

Aeotec

Aeotec AEOEZWA009 Bedienungsanleitung

Aeotec

Aeotec Water Sensor 7 Pro Bedienungsanleitung

Aeotec

Aeotec Button Bedienungsanleitung

Aeotec

Aeotec Water Sensor 7 Pro Bedienungsanleitung

Aeotec

Aeotec Water Sensor 7 Pro Bedienungsanleitung

Aeotec

Aeotec Doorbell Gen5 Bedienungsanleitung

Aeotec

Aeotec Door / Window Sensor 7 Bedienungsanleitung

Aeotec

Aeotec Water Sensor 7 Pro Bedienungsanleitung

Aeotec

Aeotec Door / Window Sensor 7 Bedienungsanleitung

Beliebte Zubehör Handbücher anderer Marken

Hillco

Hillco 2810 Bedienungsanleitung

Siemens

Siemens QSA2700D Bedienerhandbuch

Contours

Contours ZY024 Bedienungsanleitung

Saivod

Saivod VS621 Bedienungsanleitung

Virtuox

Virtuox VirtuCLEAN 2.0 Bedienungsanleitung

SCE

SCE ENVIRO-THERM SCE-TE170B24VSS Bedienungsanleitung

Z-Wave

Z-Wave HSD-200Z Bedienungsanleitung

turck

turck FMX-IM-2UPLI63FX Bedienungsanleitung

Decagon Devices

Decagon Devices 10HS Bedienungsanleitung

UPPAbaby

UPPAbaby Cup Holder Bedienungsanleitung

Elko

Elko SmartSensor Leakage Wireless Bedienungsanleitung

Grizzly

Grizzly H8371 Bedienungsanleitung

Panasonic

Panasonic HG-T Series Bedienungsanleitung

IFM Electronic

IFM Electronic Efector 250 Series Referenzhandbuch

DigiDesign

DigiDesign 888/24 I/O Bedienungsanleitung

PROZIS

PROZIS QUAY Bedienungsanleitung

patagonia

patagonia PSI Vest Bedienungsanleitung

SFC Energy

SFC Energy EFOY GO! Bedienungsanleitung