Agilent Technologies 3588A Bedienungsanleitung

Agilent Technologies

3588A

Data Sheet

Product Specifications

Amplitude Specifications

All receiver specifications apply from 10 Hz to 150 MHz and include 30 minute

warmup from ambient conditions unless otherwise noted. Typical performance is

applicable over ±5°C from the most recent autocalibration and is not warranted.

Supplemental characteristics are non-warranted functional and feature

information.

Amplitude measurement range

Maximum Safe Input Level: 50/75 Ohm 1M Ohm

Average Continuous Power: 26 dBm - (10 Hz to 150 MHz)

Combined AC/DC ±4 Vpk ±25 Vpk

Maximum Measured Input 20 dBm

Input range settings (characteristic only)

50 Ohm input (in 10 dB steps) +20 dBm to -20 dBm

75 Ohm input (in 10 dB steps) +22 dBm to -18 dBm w/included adapter

1M Ohm input 0 dBm (for reference impedance of 50 Ohm)

A/D overload level:2 dB (relative to selected range)

Dynamic range

Note: Dynamic range specifications apply with the source turned off.

Noise Level, 50 Ohm input (dBm/Hz using the marker noise function, -20 dBm

range)

The 50 ohm input noise level (dBm/Hz using the marker noise function,

-20 dBm range) will be typically -135dBc/Hz @ 1KHz and - 140 dBc/Hz

above 30 KHz to 100 MHz.

Specified for swept spectrum mode, with 50 Ohm input and low-distortion

mode off. Degrade 10 dB if in low-distortion mode and 2 dB if using

75 Ohm input.

For 1M Ohm input, noise is <-110 dBm/Hz below 40 MHz, with 1/f corner at

100 kHz.

Input noise is degraded 4 dB in narrowband zoom mode for spans >10 kHz, and 3 dB

for start frequency <30 kHz.

Note: Equivalent noise bandwidth is narrower than 1 Hz for spans below

150 Hz in the narrowband zoom mode, providing additional reduction in

phase noise from that shown above. This maintains good dynamic range,

even for extremely small offset frequencies in narrow spans. Noise is

reduced by 10 × log [1/noise bandwidth] dBc relative to the above graph.

Spurious Responses

General Spurious

Unless specifically mentioned in other spurious specifications, spurious

responses are <-70 dBc for signal levels = range. (<-80 dBc typical)

Harmonic distortion

Low-distortion mode, 50 and 75 Ohm inputs: Harmonic distortion products

are <-80 dBc (<-90 dBc typical) for spectrally pure input signals with

total input power level = range. Degrade specification by 10 dB when

low-distortion mode is off.

1M Ohm input:<-65 dBc (<-75 dBc typical)

Degrade harmonic distortion specifications by 10 dB (5 dB for 1M Ohm input) when

input frequency is less than 30 kHz.

Intermodulation distortion

Low-distortion mode, 50 and 75 Ohm inputs: Intermodulation distortion

products are <-80 dBc (<-90 dBc typical) with respect to 2 tones 6 dB

below range. Degrade specification by 10 dB when low-distortion mode

is off.

1M Ohm input: <-65 dBc (<-75 dBc typical)

Degrade intermodulation distortion specifications by 10 dB (5 dB for 1 MOhm

input) when input frequency is less than 30 kHz.

Residual responses

Residual responses are less than -110 dBm on the -20 dBm range.

Degrade specification by 10 dB when low-distortion mode is on.

Degrade 10 dB for 40 kHz spans in narrowband zoom mode.

Image, multiple and out-of-band responses

<-70 dBc (<-80 dBc typical) where applied signal level = range.

Local oscillator feedthrough

Local oscillator feedthrough (appears as signal at dc) is >20 dB below

range. Degrade specification by 10 dB when low-distortion mode is on.

Full Scale Absolute Accuracy

(applies over entire 0 to 55°C temp range)

10 Hz- 100 Hz- 30 kHz- 300 kHz- 40 MHz-

100 Hz 30 kHz 300 kHz 40 MHz 150 MHz

50 Ohm ±2.5 dB ±1.0 dB ±0.5 dB ±0.4 dB0.5 dB

input (1 dB typ) (0.5 dB typ) (0.2 dB typ) (0.2 dB typ)(0.2 dB typ)

75 Ohm ±2.5 dB ±1.0 dB ±0.8 dB ±0.8 dB ±0.8 dB

Input

1M Ohm ±2.5 dB ±1.0 dB ±0.6 dB ±0.6 dB

Input

The calibration procedures produce the greatest accuracy at 300 kHz.

Full-scale absolute accuracy at 300 kHz is ±0.3 dB (0.1 dB typical)

when input level = range.

Accuracy is specified for manual frequency or for sweeps where sweep

time is increased by a factor of 4. Add ±0.1 dB for autocoupled

sweep times.

Narrowband zoom: Measurement data is "windowed" in the FFT operation

of the narrowband zoom mode to optimize amplitude accuracy or frequency

resolution. This adds the following frequency response errors to the

full-scale absolute accuracy specifications.

High accuracy mode (Flat-Top window): ±0.005 dB

High resolution mode (Hanning window): +0, -1.5 dB

Scale fidelity (linearity)

Level Specified Typical

0 to -30 dB <0.05 dB 0.02 dB

-30 to -40 dB <0.1 dB 0.03 dB

-40 to -50 dB <0.3 dB 0.05 dB

-50 to -60 dB <0.5 dB 0.10 dB

-60 to -70 dB <0.7 dB 0.10 dB

-70 to -80 dB - 0.25 dB

-80 to -90 dB - 0.25 dB

-90 to -100dB - 0.40 dB

-100 to -110 dB - 0.70 dB

-110 to -120 dB - 4.0 dB

Level is relative to the input range

Specifications are valid for frequencies >100 kHz.

Example: To compute the typical accuracy for a signal of -45 dBm at

100 MHz with 50 Ohm full-scale range of -20 dBm and manual sweep,

sum the typical full-scale absolute accuracy and scale fidelity.

i.e. (0.2 dB + 0.02 dB) = 0.22 dB

Input Port Return Loss: >20 dB

Frequency Specifications

Frequency range

Specifications apply over the range of 10 Hz to 150 MHz

(10 Hz to 40 MHz for 1M Ohm input).

Frequency accuracy

Frequency accuracy is the sumofinitial accuracy, aging and

frequency counter resolution. Accuracy is measured with

frequency counter function.

Initial Accuracy Without opt. 001 With opt. 001

20 to 30°C ±0.5 ppm ±0.01 ppm

0 to 55°C ±3.0 ppm ±0.07 ppm

Aging ±0.25 ppm/mo. ±0.125 ppm/mo

*Add ±0.1 ppm if instrument is on < 48 hours

Frequency Counter Resolution: 0.1 Hz

Drift/residual FM

Frequency drift and residual FM are negligible, as the Agilent 3588A is

fully synthesized (phase-locked to frequency reference) during

sweeps. For frequency accuracy during sweeps, see the accuracy

specifications above.

Frequency span range (characteristic only)

Swept spans:

Range: 10 Hz to 150 MHz, and zero span

Resolution: 0.1 Hz

Accuracy: Greater of 0.1 Hz or .125% of span

Start/stop freq: 0 Hz to 150 MHz

Narrowband zoom spans:

Range: 1.23 Hz to 40 kHzin ×2 steps

Accuracy: ±0.001% of span

Resolution bandwidth

Swept spectrum: 1.1 Hz to 17 kHz ±10%

Narrowband zoom:

High-accuracy mode: 0.90% of span (11 mHz-360 Hz)

High-resolution mode: 0.37% of span (4.5 mHz-148 Hz)

Bandwidth selectivity

(shape factor or ratio of -60 dB to -3 dB bandwidths)

Swept spectrum mode (see also filter comparison graph)

Manual sweep: <4.0:1

Auto-coupled sweep: 4.3:1 (typical)

Auto-coupled oversweep: 5.1:1 (typical)

Narrowband zoom mode

High-accuracy mode: 2.6:1

High-resolution mode: 9.1:1

Narrowband zoom (FFT) equivalent noise bandwidth

High-accuracy mode: 0.955% of span

High-resolution mode: 0.375% of span

Measurement speed (maximum, characteristic only)

Sweep rate, oversweep off: RBW ÷ 2 Hz/s

Sweep rate, oversweep on: 4 × (RBW ÷ 2) Hz/s

Narrowband zoom mode: >7 measurements/s (for spans >=10 kHz)

Narrowband zoom (FFT): 400 ÷ span (Hz) seconds time record length

Note: Traditional analog RBW filters are usually swept at RBW ÷ 2 Hz/s

(or slower), to limit amplitude errors due to sweeping to <0.1 dB.

The oversweep mode of the Agilent 3588A provides up to 4 times faster

sweep times without increased error.

HP-IB binary trace output: approx. 120 ms/trace

Video Bandwidth

Coupled to RBW from (1.54 × RBW) to (0.012 × RBW) in 7 steps, and OFF

Source Specifications

Frequency range(characteristic only):10 Hz to 150 MHz

Amplitude range: +10 to -59.9 dBm and OFF

Amplitude resolution: 0.1 dBm

Absolute amplitude accuracy: ±1 dB

(300 kHz, +10 dBm output)

Dynamic accuracy

(add to absolute accuracy): Add 0.02 dB/dB below +10 dBm

Frequency response ±1 dB

(Variation relative to

level at 300 kHz):

Spurious products

Harmonic products: <-30 dB

Non-harmonic products: <-40 dB

Noise: <-80dB

Relative to the carrier in a 1 Hz bandwidth for offsets greater

than 500 Hz from the carrier)

Output Port Return Loss: >20 dB

General Specifications

Environmental

Temperature, standard instrument

Operating: 5 to 50°C

Storage (no disk in drive): -20 to 60°C

Temperature, delete disk option

Operating: 0 to 55°

Storage: -40 to 70°C

Humidity, non-condensing,

standard instrument

Operating: 8% to 80% at 30°C

Storage (no disk in drive): 5% to 95%

Humidity, non-condensing,

delete disk opt.

Operating: 5% to 95% at 40°C

Storage: 5% to 95% at 40°C

Altitude, standard instrument

Operating: 2150m (7000 ft)

Storage: 4570m (15,000 ft)

Altitude, delete disk option

Operating: 4570m (15,000 ft)

Storage: 4570m (15,000 ft)

Calibration

Calibration Interval: 1 year

Warmup time: 30 minutes

Physical

Power requirements

115 VAC operation 19-132 Vrms, 47-440 Hz

230 VAC operation 198-264 Vrms, 47-66 Hz

Max power dissipation 450 VA

Weight

Net: 28 kg (61 lbs)

Shipping: 38 kg (81 lbs)

Dimensions

Height: 222 mm (8.75 in)

Width: 425.5 mm (16.75 in)

Depth: 630 mm (24.8 in)

Inhaltsverzeichnis

Andere Agilent Technologies Messgerät Handbücher

Agilent Technologies

Agilent Technologies 4349B Bedienungsanleitung

Agilent Technologies

Agilent Technologies E8363BU/CU-068 Installations- und Betriebshandbuch

Agilent Technologies

Agilent Technologies DSOX4USBSQ USB 2.0 Bedienungsanleitung

Agilent Technologies

Agilent Technologies 8712ET Bedienungsanleitung

Agilent Technologies

Agilent Technologies 89410A Handbuch

Agilent Technologies

Agilent Technologies OmniBER 725 Bedienungsanleitung

Agilent Technologies

Agilent Technologies TapeStation 4200 Montageanleitung

Agilent Technologies

Agilent Technologies 81950A Bedienungsanleitung

Agilent Technologies

Agilent Technologies Cary 60 Bedienungsanleitung

Agilent Technologies

Agilent Technologies 4339B Bedienungsanleitung

Agilent Technologies

Agilent Technologies M9302A Bedienungsanleitung

Agilent Technologies

Agilent Technologies E4440A Kurzanleitung

Agilent Technologies

Agilent Technologies PSA Series Installations- und Betriebshandbuch

Agilent Technologies

Agilent Technologies LogicWave Bedienungsanleitung

Agilent Technologies

Agilent Technologies FieldFox MW N9913A Bedienungsanleitung

Agilent Technologies

Agilent Technologies 4155C Bedienungsanleitung

Agilent Technologies

Agilent Technologies 8753ET Bedienungsanleitung

Agilent Technologies

Agilent Technologies 1290 Infinity II Bedienungsanleitung

Agilent Technologies

Agilent Technologies 4395A Bedienungsanleitung

Agilent Technologies

Agilent Technologies ESA E4401B Installations- und Betriebshandbuch

Agilent Technologies

Agilent Technologies 11980A Bedienungsanleitung

Agilent Technologies

Agilent Technologies ENA Series Bedienungsanleitung

Agilent Technologies

Agilent Technologies 4286A Bedienungsanleitung

Agilent Technologies

Agilent Technologies PSA Series Kurzanleitung

Beliebte Messgerät Handbücher anderer Marken

Suaoki

Suaoki D40 Bedienungsanleitung

Elster

Elster BK-G1.6 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Deltabar FMD71 Handbuch

Duratool

Duratool D03128 Bedienungsanleitung

Vega

Vega VEGAPULS 65 Bedienungsanleitung

Tonghui

Tonghui TH2618B Bedienungsanleitung

Tenmars

Tenmars TM-801 Bedienungsanleitung

MSR

MSR 145 Bedienungsanleitung

TPS

TPS WP-82 Bedienungsanleitung

ELMETRON

ELMETRON CP-511 Bedienungsanleitung

PCB Piezotronics

PCB Piezotronics 003C30 Bedienungsanleitung

Tenma

Tenma 72-10465 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Proline Promag 50 Technische Daten

Siemens

Siemens SITRANS F Coriolis FCT030 Stücklistenhandbuch

KLINGER

KLINGER CMF V Series Bedienungsanleitung

EXFO

EXFO FTB-2 Bedienungs- und Wartungshandbuch

Keysight

Keysight M8290A Bedienungsanleitung

ADTEK

ADTEK MW-5 Bedienungsanleitung