Agilent Technologies J2126A Installations- und Betriebshandbuch

Agilent J2126/7A

Transmission Test Sets

Installation and

Verification Manual

sdh_Lynx2.book Page 148 Wednesday, April 17, 2002 12:49 PM

Agilent Technologies

Agilent J2126/7A

Transmission Test Set

Installation and

Verification Manual

2 Installation and Verification Manual

Notices

No part of this manual may be reproduced in

any form or by any means (including elec-

tronic storage and retrieval or translation

into a foreign language) without prior agree-

ment and written consent from Agilent

Technologies UK Limited as governed by

international copyright laws.

Manual Part Number

J7280-90012

Edition

First edition, September 2002

Printed in UK

Agilent Technologies UK Limited

Transmission & Transport Test Operation

South Queensferry, West Lothian, Scotland

EH30 9TG

Warranty

The material contained in this docu-

ment is provided “as is,” and is sub-

ject to being changed, without notice,

in future editions. Further, to the max-

imum extent permitted by applicable

law, Agilent disclaims all warranties,

either express or implied, with regard

to this manual and any information

contained herein, including but not

limited to the implied warranties of

merchantability and fitness for a par-

ticular purpose. Agilent shall not be

liable for errors or for incidental or

consequential damages in connec-

tion with the furnishing, use, or per-

formance of this document or of any

information contained herein. Should

Agilent and the user have a separate

written agreement with warranty

terms covering the material in this

document that conflict with these

terms, the warranty terms in the sep-

arate agreement shall control.

Tec hnology Li ce ns es

The hardware and/or software described in

this document are furnished under a license

and may be used or copied only in accor-

dance with the terms of such license.

Restricted Rights Legend

If software is for use in the performance of a

U.S. Government prime contract or subcon-

tract, Software is delivered and licensed as

“Commercial computer software” as

defined in DFAR 252.227-7014 (June 1995),

or as a “commercial item” as defined in FAR

2.101(a) or as “Restricted computer soft-

ware” as defined in FAR 52.227-19 (June

1987) or any equivalent agency regulation or

contract clause. Use, duplication or disclo-

sure of Software is subject to Agilent Tech-

nologies’ standard commercial license

terms, and non-DOD Departments and

Agencies of the U.S. Government will

receive no greater than Restricted Rights as

defined in FAR 52.227-19(c)(1-2) (June

1987). U.S. Government users will receive

no greater than Limited Rights as defined in

FAR 52.227-14 (June 1987) or DFAR

252.227-7015 (b)(2) (November 1995), as

applicable in any technical data.

Safety Notices

CAUTION

A CAUTION notice denotes a haz-

ard. It calls attention to an operat-

ing procedure, practice, or the like

that, if not correctly performed or

adhered to, could result in damage

to the product or loss of important

data. Do not proceed beyond a

CAUTION notice until the indicated

conditions are fully understood and

met.

WARNING

A WARNING notice denotes a

hazard. It calls attention to an

operating procedure, practice, or

the like that, if not correctly per-

formed or adhered to, could result

in personal injury or death. Do not

proceed beyond a WARNING

notice until the indicated condi-

tions are fully understood and

met.

Installation and Verification Manual 3

In This Guide…

You will find information for installing and verifying the

performance of your instrument

1 Introduction

This chapter provides a brief description of the product and

also all safety requirements the user should be aware of when

using the instrument.

2 Installation (Getting Started)

This chapter provides general information on how to install and

connect up the instrument.

3PerformanceTests

This chapter details the procedures to test the performance of

the instrument and provides a test record table to record the

results of the tests.

4 Self Test Overview

This chapter details all of the Self Test procedures.

5 ETSI/ANSI Terminology

This chapter provides a table explaining the equivalent

SDH/SONET terms.

4 Installation and Verification Manual

Conventions Used in this Manual

The conventions used in this manual to illustrate instrument

keys and display information are as follows:

<Menu> This is an example of a hardkey. Hardkeys (located to the right

of the display) are used to give access to different sets of

instrument settings, or select dedicated instrument functions.

Menu Items Menu items appear in text as bold face with the greater than (>)

symbol separating each menu level. For example, if you are

instructed to choose Errors and Alarms from the Test Functions

menu item, it appears as Test Functions > Errors and Alarms.

Field Items Field items you are instructed to select in a window will appear

in bold face, for example select Signal Rate field.

Drop Down Lists The item you must select from a drop down list is also shown in

bold. For example, select Signal Rate field and choose STM-1 or

OC-3 from the drop down list.

Installation and Verification Manual 5

1 Introduction

Product Description 12

SONET/SDH Capability 12

Ethernet Capability 13

Option Guide 15

Mainframes and Potential Test Rate Capability 15

Optical Interfaces 16

Optical Connectors (product options) 16

Alternative Optical Connectors (available accessories) 17

Ethernet Options 17

Other Options 17

Accessories 18

General Information 19

Responsibilities of the Customer 19

Certification 19

Assistance 19

Instruments Covered By Manual 20

Storage and Shipment 21

Temperature 21

Altitude 21

Repackaging for Shipment 21

Weight and Dimensions 22

Safety Information 23

Safety Precautions 23

Safety Symbols 24

Avoiding Problems When Making Measurements 26

Operators Maintenance 27

Cleaning Optical Connectors 27

Statement of Compliance 29

Noise Declaration (German) 30

Electromagnetic Compatibility 30

Declaration of Conformity 30

Contents

6 Installation and Verification Manual

2 Installation (Getting Started)

Preparation 32

Initial Inspection 32

Operating Environment 32

Preparation for Use 33

Power Requirements 33

Connecting to the Power Supply 34

Power Cable 35

Removing the Instrument Covers 36

Connecting the Mouse Cable 36

Useful Information When Requesting Support 37

Operation Checks on Delivery 38

Power-up Sequence 38

Recalling Default Settings 39

Back-to-Back Functional Checks 40

What to do if the Test fails 45

Optical Connector Safety Information 46

Laser Warnings and Cautions 46

Laser Warning Symbols 48

Avoiding Optical Receiver Overload 48

Additional Precautions for Service Engineers 49

ESD Precautions 49

Top Panel Connectors 51

Optical Out Ports 52

Optical In Ports 53

Clock Ports 54

DCC Port 55

Electrical Test Ports 56

Ethernet Ports 57

Connectors on Instrument Front/Left Side Panel 58

Connectors on Instrument Front/Right Side Panel 59

Instrument Reboot (Cold Start) 61

Installation and Verification Manual 7

3PerformanceTests

Introduction 64

Equipment Required 64

Performance Test Record 64

Calibration Check Cycle 64

Instrument Option Configuration 64

Recommended Test Equipment 65

Self Test Loopback Cables and Accessories 66

Recall Default Settings 67

Performance Self Test 68

Description of the Performance Self Test 68

Loopback Connections Required for Self Test 69

How to run the Self Test 72

What to do if the Self Test fails 72

Internal Reference Clock Accuracy 73

Specification 73

Description 73

Equipment Required 74

Procedure 74

Alternative DS1 Clock test (if suitable DSn Test Set is not

available) 78

External Clock Reference Inputs and Clock Reference Output 79

Specifications 79

Description 79

Equipment Required 79

Procedure 80

Optical Pulse Mask and Output Characteristics 86

Specifications 86

Description 86

Equipment Required 87

Procedure 87

52/155 and 622 Mb/s Optical Output Checks 88

OC-1/STM-0 Power Level and Eye Mask Tests 88

OC-3/STM-1 Power Level and Eye Mask Tests 90

OC-12/STM-4 Power Level and Eye Mask Tests 91

8 Installation and Verification Manual

2.5 Gb/s Optical Output Checks 93

OC-48/STM-16 Power Level and Eye Mask Tests 93

10 Gb/s Optical Output Checks (if fitted) 95

OC-192/STM-64 Power Level and Eye Mask Tests 95

Optical Receiver Sensitivity, Optical Power and Frequency

Measurement 98

Specifications 98

Description 99

Equipment Required 100

Procedure 100

Checking the Receiver Minimum Sensitivity Margin Against Laser

Transmitter Extinction Ratio (ER) 113

Electrical Pulse Mask and Output Level Characteristics 114

Specifications 114

Description 115

Equipment Required 115

Procedure 115

DS1 Output Mask Test 116

2 Mb/s Balanced Output Mask Tests 118

2 Mb/s Unbalanced Output Mask Tests 121

8 Mb/s Output Mask Tests 123

34 Mb/s Output Mask Tests 125

DSX-3 Output Mask Tests 127

140 Mb/s Output Mask Tests 129

51.84 Mb/s (STS-1) Output Mask Tests 132

155 Mb/s Output Mask Tests 136

Performance Test Record 140

Andere Handbücher für J2126A

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Agilent Technologies Prüfgeräte Handbücher

Agilent Technologies

Agilent Technologies 35670A Bedienungsanleitung

Agilent Technologies

Agilent Technologies e6601a Montage- und Bedienungsanleitung

Agilent Technologies

Agilent Technologies Agilent 34980A Bedienungsanleitung

Agilent Technologies

Agilent Technologies InfiniiVision 3000 X- Series Bedienerhandbuch

Agilent Technologies

Agilent Technologies 3000 Series Bedienungsanleitung

Agilent Technologies

Agilent Technologies 8648A Bedienungsanleitung

Agilent Technologies

Agilent Technologies 81250 Bedienungsanleitung

Agilent Technologies

Agilent Technologies 41900A Bedienungsanleitung

Agilent Technologies

Agilent Technologies Infiniium 90000 Q-Series Bedienungsanleitung

Agilent Technologies

Agilent Technologies InfiniiVision 6000 Series Bedienungsanleitung

Agilent Technologies

Agilent Technologies InfiniiVision MSO6104A Kurzanleitung

Agilent Technologies

Agilent Technologies 8960 Betriebsanleitung

Agilent Technologies

Agilent Technologies 3070 Series Benutzerhandbuch

Agilent Technologies

Agilent Technologies Infiniium Bedienungsanleitung

Agilent Technologies

Agilent Technologies 16191A Bedienungsanleitung

Agilent Technologies

Agilent Technologies 8960 Series 10 Bedienungsanleitung

Agilent Technologies

Agilent Technologies N4419B Bedienungsanleitung

Agilent Technologies

Agilent Technologies InfiniiVision 2000 X-Series Bedienungsanleitung

Agilent Technologies

Agilent Technologies Infiniium 8000A Bedienungsanleitung

Agilent Technologies

Agilent Technologies E4406A VSA Series Installations- und Betriebshandbuch

Agilent Technologies

Agilent Technologies U4002A Bedienungsanleitung

Agilent Technologies

Agilent Technologies E6630A Bedienungsanleitung

Agilent Technologies

Agilent Technologies 8935 Series Bedienungsanleitung

Agilent Technologies

Agilent Technologies ProBER 2 Montageanleitung

Beliebte Prüfgeräte Handbücher anderer Marken

SMART

SMART KANAAD SBT XTREME 3G Series Bedienungsanleitung

Lifeloc

Lifeloc R.A.D.A.R. Bedienungsanleitung

Fluke

Fluke T5-600 Bedienungs- und Montageanleitung

Mercury

Mercury TSL01 Bedienungsanleitung

MAHA

MAHA MBT Series Bedienungsanleitung

Fuji Electric

Fuji Electric P-61 Bedienungsanleitung

ETC

ETC SealerAtor Bedienungsanleitung

Skyfine

Skyfine ETHYWAY V2 Bedienungsanleitung

Appion

Appion G5 Twin Bedienungsanleitung

PCB Piezotronics

PCB Piezotronics 8159-0112A Bedienungsanleitung

BW Technologies

BW Technologies MicroDock II Bedienungsanleitung

Sun Nuclear

Sun Nuclear 1027 Bedienungsanleitung

Biomark

Biomark HPR LITE READER Bedienungsanleitung

Hioki

Hioki 3169-20 Bedienungsanleitung

Ashcroft

Ashcroft ATE-100 Bedienungsanleitung

Rohde & Schwarz

Rohde & Schwarz RTA4000 Bedienungsanleitung

Ritmix

Ritmix RAT-701 Bedienungsanleitung

Sealey

Sealey TA130 Bedienungsanleitung