Andonstar AD407 Bedienungsanleitung

Digital Microscope AD407 Users Manual

LIST OF CONTENTS

Safety and Maintenance ................................................................3

Basic Parameters ..............................................................................3

What’s in the box ..........................................................................4

Assembly.............................................................................................5

Buttons.................................................................................................5

Quick start...........................................................................................7

Adjusting the Magnification and Focus...............................7

Using a Micro SD Card to Save Images ...............................7

Reviewing and Managing Images..........................................8

Settings............................................................................................8

Warranty........................................................................................... 11

Safety and Maintenance

1. This microscope is safe and low-maintenance, as long as common sense is employed.

2. The assembly includes small parts, particularly the thumbscrews used to hold the main device in place.

Do NOT allow unsupervised access by infants or toddlers.

3. The microscope is not intended for field use. It is not waterproof, and should not be exposed to extreme

temperatures. Treat as you would any other electronic device, such as laptop or tablet.

4. The surface of the lens at the bottom of the main device should be cleaned whenever you start to notice

a degradation in image quality. Use a few drops of lens-cleaning fluid on lens tissues or use a microfiber

cleaning cloth.

5. The rest of the microscope can be cleaned with a damp cloth.

6. The display on the device is very fragile. Please use with care. Do not drop, press hard or touch the

display with sharp objects. The display is not waterproof, please clean it with dry and soft material. Do not

press the display when adjusting the angle of the display.

Basic Parameters

Image sensor

4 Mega Pixels HD Sensor

Video output

UHD 2880X2160 24FPS; FHD1920X1080 60FPS/30FPS,

HD1280X720 120FPS,

Video format

MP4

Magnification Ratio

Up to 270×(HDMI monitor 27 inch)

Photo resolution

MAX 4032*3024 (12M 4032*3024)

Photo format

JPG

Minimum focus distance

5cm

Frame Rate

Max 120f/s (under 600 Lux Brightness& HDP120)

Storage

Micro-SD card, up to 32G

PC support

Power source

5V DC

Stand size

20cm*12cm*19cm

Screen size

7 inch

What’s in the box

(P1,what’s in the box)

Accessories

Metal Base, Optical Bracket, Power Adapter, Switch Cable,

HDMI Cable, Remote, UV filter, Screws*2, Screwdriver, Users

Manual

Packing data

1.6KG/32*22*10CM

(P2,Assembly1) (P3,Assembly2)

Assembly

1. Screw the optical bracket onto the base (see the left picture above,P2 ).

2. Once you have done so, if the bracket is not aligned over the base, unscrew the locking ring, adjust the

bracket’s direction, and then turn the locking ring clockwise until it is tight.

(After doing so, i t will still be possible to hold the base and

turn the bracket i f sufficient force i s applied, but i t will not spin freely.)

3. Loosen the small thumbscrews onthe optical bracket.

4. Slide the optical stack i n tothe ring ofthe optical bracket.

5. Tighten the thumbscrews to hold the optical stack in place.

Ifdone correctly, you should b e able to not just turn the focus controller ofthe optical stack freely, but also

freely adjust the monitor, the angel between the base and the optical bracket, while the rest of

microscope remains i n place. If you have any question or problem for assembly, please contact us as soon

as possible, so you won’t damage the device during assembly.

Buttons

(P4, buttons)

①Power on/off

②Mode/menu

③Up

④Down

⑤OK/Start video record

⑥Picture capture

⑦Infrared sensor (when you are using the

remote, please point the remote to this so the

device would response)

⑧Focus controller

⑩Memory card slot

⑪USB port

⑫HMDI port

(P5, remote buttons)

(P6 connect )

Quick start

Connect

To use the microscope stand alone, you need to connect the optical stack to the power supply via the

switch cable. See the picture(P6) above.

Switch on

Then press and hold the Power button (①from the P4 “Buttons”) underneath the display until the

display turns on. (It may turn on automatically while you connecting cables at the first time, and it’s

totally fine.)

*Troubleshooting

If the display freezes, locate the “reset ” hole on the back of the monitor. Use a narrow object such as an

unfolded paperclip to depress the button located inside. This resets all settings to their factory values and

restarts the display. It does not erase saved images or video.

Adjusting the Magnification and Focus

①Use the large knobs on the optical bracket to raise or lower the optical stack to the desired height. The

lower the height, the greater the magnification is. But be careful not to let the bottom of the stack contact

the object being imaged. (Note that you may need to reposition the spotlights as you move the stack up

or down.)Turn the Focus controller( ⑧from the P4 “Buttons”) to focus the image.

②To increase the digital magnification, press and hold the Up button (③from the P4 “Buttons” ) until

the desired digital magnification(up to an additional 3x beyond the optical magnification) is reached.

Use the Down (number ④ from the picture “Buttons”) button to decrease the digital magnification.

Using a Micro SD Card to Save Images

By using a Micro SD card (not provided), you can save images and videos to review later or export to a

computer or other device .

Insert the Micro SD card in to the TF slot on top back of the monitor. (be careful with the direction. The

side which has metal exposed, should face down. See the picture 6 )

Push it in until you hear a click. (If you don't push it in far enough, it will be ejected.)

*If you insert the card while the microscope’s working, the device would switch off automatically. Press

the Power button and hold it until the screen lights up again.

The Mode button(number ② from the picture “Buttons”, marked with an "M") can be used to cycle

between three modes: video standby ( ), still image ( ), and review ( ). In video standby mode, there

are white color numbers located right to the icon, shows how many time the rest storage of the card

would allow you to record video.

To record videos

Press the OK button(⑤) briefly to begin recording. The elapsed time(red color) in the recording will

appear at the top left. To stop recording, hit the OK button again. The OK button on the remote has the

same function.

To Capture pictures

Press the Picture Capture button(⑥)(Marked with a camera) briefly to capture an image. The picture

capture button on the remote has the same function.

Note: You can’t take pictures or videos in Preview mode

Reviewing and Managing Images.

T o review and manage images onthe display, use the Mode button to select review

mode. Use the Up and Down buttons to cycle through the pictures and videos.

T o play a video, press the OK button to start play. Press the OK button again to pause. Press Mode

button to stop playing the current video.

Hit the Mode button again to exit playback mode.

While reviewing a still image orvideo, the Menu button can b e used toprovide additional options. Press

the Menu button and hold for a while till options show up.

Delete: Delete Current: deleting just the current image/video; Delete All:

deleting all unprotected images and videos;

Protect: Lock Current/All: provides protection for the current/all image/video from deleting accidentally,

but not from Format function; Unlock Current/All: unlock the current/all image/video.

Settings

In each mode, press the M button and hold it for a while until the Video/Still/Playback Menu shows up

on the display(Or you can press MENU button on the remote). Hit M button again, get into the general

Setup Menu.

For example, if you are in Video standby mode, and you press MENU, this is the first menu would show,

the “Video menu”:

Inhaltsverzeichnis

Andere Andonstar Mikroskop Handbücher

Andonstar

Andonstar AD206S Bedienungsanleitung

Andonstar

Andonstar AD409-Max Bedienungsanleitung

Andonstar

Andonstar ADSM302 Bedienungsanleitung

Andonstar

Andonstar ADSM201 Bedienungsanleitung

Andonstar

Andonstar AD108 Bedienungsanleitung

Andonstar

Andonstar AD205 Bedienungsanleitung

Andonstar

Andonstar AD409 Bedienungsanleitung

Andonstar

Andonstar 246S Bedienungsanleitung

Andonstar

Andonstar 246 Bedienungsanleitung

Andonstar

Andonstar 246 Bedienungsanleitung

Andonstar

Andonstar AD203 Bedienungsanleitung

Andonstar

Andonstar AD409-Pro Bedienungsanleitung

Andonstar

Andonstar ADSM201 Bedienungsanleitung

Andonstar

Andonstar A1 Bedienungsanleitung

Andonstar

Andonstar A1 Referenzhandbuch

Beliebte Mikroskop Handbücher anderer Marken

Thermo Scientific

Thermo Scientific Nicolet iN10 Leitfaden

National

National DC3-163 Bedienungsanleitung

KERN Optics

KERN Optics OPE-1 Bedienungsanleitung

OPTIKA MICROSCOPES

OPTIKA MICROSCOPES B-150D Bedienungsanleitung

Prior

Prior Lux POL Bedienungsanleitung

Opitec

Opitec Smartscoop 115615 Bedienungsanleitung

KERN

KERN OPO-1 Bedienungsanleitung

Topcon

Topcon SP-1P Bedienungsanleitung

Motic

Motic PA43 Bedienungsanleitung

Leica

Leica DVM5000 Benutzerhandbuch

MshOt

MshOt MZ62 Bedienungsanleitung

KERN Optics

KERN Optics OZR-5 Bedienungsanleitung

VWR

VWR VisiScope 384 Series Bedienungsanleitung

Nikon

Nikon ECLIPSE E200 POL Bedienungsanleitung

Leica

Leica DI C800 Handbuch

ThermoFisher Scientific

ThermoFisher Scientific Continuµm Bedienungsanleitung

ThermoFisher Scientific

ThermoFisher Scientific Continuµm Bedienungsanleitung

Olympus

Olympus SZ61 Bedienungsanleitung