Assa Abloy RIXSON W91DCP Bedienungsanleitung

ISW91DCP 05/20

Model W91DCP Overhead Concealed Closer

Non-Hold Open and Hold Open

Wood Frame Installation Instructions

or in part without the express written permission of ASSA ABLOY Accessories and Door Controls Group, Inc. is prohibited.

Pour la version francaise voir www.nortondoorcontrols.com.

READ AND FOLLOW ALL INSTRUCTIONS. SAVE THESE INSTRUCTIONS.

This product can expose you to lead which is known to the state of

California to cause cancer and birth defects or other reproductive harm.

For more information go to www.P65warnings.ca.gov.

WARNING

Model W91DCP (Left Hand shown)

4-1/2" x 4-1/2" Butt or 3/4" Offset Pivot Hung; consult factory if other means

Tools Needed Supplied Fasteners

Components

Wood Mounting Clips

(90257-nish)

Slider

(90253)

Optional Hold Open

Assembly (90254)

Retrot Track Spacer and Screws,

Optional (90260)

Not for new installation. Replacement only.

Consult factory.

Closer Body

91DCP LAP x (Specify

hand and function)

Cover Plate

LH: 90272-(nish)

RH: 90275-(nish)

Track

(90239)

Non Hold Open Stop

Block (90255)

Closer

Screw Pack

(90241-nish)

Track

Screw Pack

(90242)

Arm

LH: 90236-DCP (nish)

RH: 90237-DCP (nish)

Arm

Screw Pack

(90283-nish)

Cover Plate

Screw Pack

(90278-nish)

ISW91DCP 05/20

or in part without the express written permission of ASSA ABLOY Accessories and Door Controls Group, Inc. is prohibited.

Model W91DCP, Wood Frame

Before You Begin:

IMPORTANT:

• The Americans with Disabilities Act (ADA) requires that doors having door closers have an opening force not to

exceed 5 lbf.

• Door closer’s power size adjustment feature may require adjustment to its lowest setting to comply with ADA

opening force guidelines.

• ADA compliant closers may not latch doors, manufacturer does not guarantee latching on lower opening

force settings.

• A separate Rixson Surface Checkmate® or other door stop, supplied by others, is strongly recommended to

avoid damage to door closer and adjacent property.

• Doors should be hung on ball bearing or anti-friction hinges/pivots. Door must swing freely. For other hanging

means a special layout may be required, consult factory.

• Door and frame must be reinforced for attaching screws.

• All dimensions are given in inches (millimeters).

• An improperly installed or incorrectly adjusted door closer may cause property damage or personal injury and

will void product warranty.

• To avoid personal injury, DO NOT DISASSEMBLE THIS DOOR CLOSER BODY.

• Door closers must be securely fastened to a prepared door and frame with fasteners provided.

• HOLD OPEN option not permitted to be installed in re door assemblies.

Contents

Important.............................................................................................. 2

Before You Begin ....................................................................................... 2

Installation............................................................................................. 3

Adjustments ........................................................................................... 6

4-1/2" x 4-1/2" Butt Hinge Template..................................................................... 7

3/4" Offset Pivot Template . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

ISW91DCP 05/20

or in part without the express written permission of ASSA ABLOY Accessories and Door Controls Group, Inc. is prohibited.

Model W91DCP, Wood Frame

A. Verify frame and door installation.

1. Determine if right hand or left hand

installation. (Figure 1)

2. Verify frame is square by using a

carpenter’s square. (Figure 2)

3. Note if gaps between door and frame are

consistent. Gap should be 1/16" (1.6) at

jamb and header.

4. Using supplied templates, conrm all

dimensions of cut-outs.

Installation

Figure 1

Figure 2

Figure 3 Left Hand Shown

B. Install closer.

1. Attach wood mounting clips to closer

with 1/4-20 x 5/8" FHPMS screws

provided.

2. Install closer in prepped frame with four

(4) 14 x 1-1/2" FHPWS mounting screws

provided. (Figure 3)

NOTE: Mounting plate should be ush

with frame soft.

D. Attach arm.

C. Install cover plate.

1. Install cover plate to closer mounting

plate with six (6) 6-32 x FHPMS

mounting screws provided. (Figure 4)

Figure 4

Figure 5

1. Using provided 5/32" hex wrench and

1/4-20 x 3/4" Allen Drive with Patch

screw and washer, attach arm to closer

spindle. (Figure 5)

IMPORTANT: Arm should rest at

15° away from door side of closer

mounting plate. Arm always rotates

in direction of door.

ISW91DCP 05/20

or in part without the express written permission of ASSA ABLOY Accessories and Door Controls Group, Inc. is prohibited.

Model W91DCP, Wood Frame

E. Assemble track.

1. Slide track components into track.

(Figure 6)

NOTE:

• All track components must be placed in

track before installing track into door.

• Stop block (or optional hold open)

should be last component at hinge side

of track.

• The longer end of slider should be

pointed towards hinge end of track.

Figure 6

F. Install track to door.

1. Make sure slider and track components are

installed prior to installing track to door.

2. Install track and, if necessary, optional

spacer (replacement application only,

consult factory) using four (4) #14 x 1-5/8"

FHPWS screws provided. (Figure 7)

G. Attach arm to track.

Non Hold Open Track Components

Optional Hold Open Track Components

Figure 7

Figure 8

Figure 9

1. With provided 1/8" hex wrench, completely

tighten latch and sweep valves by turning

screws clockwise. This will allow for an easier

closer-to-door connection. (Figure 8)

2. Open door to about 45° then rotate arm over

to door.

NOTE: Arm should maintain position because

latch and sweep valves have been tightened.

3. Align slider square with arm square and

connect using provided 5/32" hex wrench and

1/4-20 x 3/4" Allen Drive with Patch screw and

washer. (Figure 9)

NOTE: If you choose to open door beyond

45°, backcheck may need to be adjusted

counter clockwise to easily rotate arm to

door position.

ISW91DCP 05/20

or in part without the express written permission of ASSA ABLOY Accessories and Door Controls Group, Inc. is prohibited.

Model W91DCP, Wood Frame

Adjustments

Latch SpeedBackcheck Sweep Speed

Spring Power Adjustment for Closing Force

(Closer shipped at lowest setting)

Model PH91DCP Model 91DCP

Closer

Size

Approx # of

360° Turns

Closer

Size

Approx # of

360° Turns

ADA 0 3 0

1 15 4 17

2 30 5 25

3 55 6 32

5° 5°

0°

75°

Speed Adjustment

Use provided 1/8" hex wrench to adjust

sweep, latch and backcheck valves to control

speed of door.

NEVER completely close backcheck valve.

NEVER use backcheck as a dead stop.

NEVER fully open valves. Valves will leak.

Do not use a power drill.

Warranty will be void.

Closing Force Adjustment

If additional force is needed, use 3/8" hex

wrench to adjust closing force. Refer to

chart.

Do not use a power drill.

Warranty will be void.

All 91 Series closers are factory set to

minimum force. Adjust closer as

necessary for more force taking into

consideration door size, weight, positive

room pressure, etc.

Optional Hold Open Adjustment

1. Insert locking tab of hold open assembly

into track slider.

NOTE: Hold open assembly should be

on hinge side of track slider.

2. Open door to desired hold open position.

3. Tighten hold open set screws to lock

down hold open assembly.

4. Pull door in closing direction to

disengage hold open assembly and track

slider.

5. Adjust hold open by turning adjustment

screw with provided 3/16" hex wrench.

NOTE: THIS FEATURE CANNOT BE USED ON

FIRE-RATED DOORS

ISW91DCP 05/20

Rixson is a brand associated with ASSA ABLOY Accessories and Door Controls Group, Inc., an ASSA ABLOY Group company.

or in part without the express written permission of ASSA ABLOY Accessories and Door Controls Group, Inc. is prohibited.

Rixson Technical Product Support:

Monroe, NC 28112 USA

Phone: 800.438.1951 ext: 6030

TechSupport.Rixson@assaabloy.com

rixson.com

H. Install removable stop.

After closer is installed and all adjustments are

complete, install removable stop.

NOTE: DO NOT drill holes into closer cover plate.

You’ve now installed the Model W91DCP Overhead Concealed Closer.

Troubleshooting

Symptom Cause Remedy

Door won’t latch

Spring tension not strong enough Increase opening force.

See Adjustments section.

Latch speed control not fast enough Adjust latch speed valve.

See Adjustments section.

Door hung on products other than

4-1/2 x 4-1/2 butts or 3/4 offset pivots

Send template for hanging means

to factory. A new installation sheet

is required. Closer will need to be

relocated.

Arm is not preloaded See Step G. Attach Arm to Door

Door is too difcult to open Spring tension is set too strong Decrease opening force.

See Adjustments section.

ISW91DCP 05/20

or in part without the express written permission of ASSA ABLOY Accessories and Door Controls Group, Inc. is prohibited.

Model W91DCP Overhead Concealed Closer Template

Butt Hinge, Wood Frame

Left Hand Shown, Right Hand Opposite

22 1

572mm

LENGTH OF TRACK

52mm

189mm

17 3

437mm

VARIES WITH

DOOR THICKNESS

32mm

22mm

27mm

22 9

573mm

23 5

600mm

LENGTH OF MORTISE

HINGE SIDE

4X 14 X 1-1/4" FHPWS

70mm

22 3

578mm

137mm

95mm

CLOSER CUTOUT

WIDTH

3mm

FROM FRAME EDGE IN

ALL CASES

MUST HAVE REMOVABLE STOP

CLOSER WOOD

MOUNTING CLIPS

4X 14 X 1-1/2" FHPWS

22 3

568mm

415

125mm

16mm

23 5

600mm

19mm

44mm

MIN FRAME

WIDTH

111

43mm

MIN CLOSER CLEARANCE

41mm

CLOSER HEIGHT

102mm

MIN FRAME WIDTH

3mm

CONTACT FACTORY FOR

ALT. CONSTRUCTION

OPTIONAL SPACER

23 5

600mm

ARM CUTOUT

STOP SIDE ONLY

TOP OF DOOR

8mm

6mm

NOTES:

FOR 180

OPENING, MAX. ALLOWABLE BUTT

HINGE SIZE IS 5" X 5".

MINIMUM STOP THICKNESS 1/2".

1/8" DOOR TO SOFFIT CLEARANCE REQUIRED.

REINFORCING PER ANSI/SDI-100

RECOMMENDED FOR HOLLOW METAL DOORS

& FRAMES.

AUXILIARY STOP RECOMMENDED.

DO NOT SCALE DRAWING.

LEFT HAND DOOR AND CLOSER SHOWN.

RIGHT HAND OPPOSITE.

A REMOVABLE HEADSTOP MUST BE USED IN COMBINATION

WITH THE CLOSER FOR PROPER INSTALLATION. MOUNTING HOLES

FOR THE HEADSTOP MUST SPAN CLOSER LENGTH. HEADSTOP MUST BE

REMOVABLE TO INSTALL CLOSER AND MAKE PROPER ADJUSTMENTS.

PRODUCT:

TEMPLATE NUMBER:

DATE:

W91DCP OHC CLOSER

OC60925

5/2020

MODEL W91DCP OVERHEAD CONCEALED CLOSER

BUTT HINGE, WOOD FRAME

MAX. DEGREE OF OPENING

W91NDCP NON HOLD OPEN (180

)

W91NDCP NON HOLD OPEN WITH TRACK STOP

(135

)

W91HDCP HOLD OPEN (105

)

www.rixson.com

CUTOUT FOR ARM

INCLUDES HEEL OF

DOOR AS SHOWN

part without the express written permission of ASSA ABLOY Accessories and Door Controls Group, Inc. is prohibited.

"A" Dimension

Standard Appilcation

1" - 1/16" (27)

Retrofit Track Option

1" - 3/8" (35)

ISW91DCP 05/20

or in part without the express written permission of ASSA ABLOY Accessories and Door Controls Group, Inc. is prohibited.

Model W91DCP Overhead Concealed Closer Template

3/4" Offset Pivot, Wood Frame

Left Hand Shown, Right Hand Opposite

22 1

572mm

LENGTH OF TRACK

VARIES WITH

DOOR THICKNESS

32mm

22mm

23 5

600mm

LENGTH OF MORTISE

116mm

25mm

162mm

16 1

410mm

21 1

546mm

HINGE SIDE

PIVOT

4X 14 X 1-1/4" FHPWS

513

148mm

70mm

95mm

CLOSER CUTOUT

WIDTH

3mm

FROM FRAME EDGE IN

ALL CASES

22 3

578mm

CLOSER WOOD

MOUNTING CLIPS

MUST HAVE REMOVABLE STOP

4X 14 X 1-1/2" FHPWS

137mm

16mm

22 3

568mm

111

43mm

MIN CLOSER CUTOUT

19mm

23 5

600mm

44mm

MIN FRAME

WIDTH

116mm

19"

483mm

ARM CUTOUT

STOP SIDE ONLY

8mm

TOP OF DOOR

102mm

MIN FRAME WIDTH

3mm

CONTACT FACTORY FOR

ALT. CONSTRUCTION

41mm

CLOSER HEIGHT

OPTIONAL SPACER

NOTES:

FOR PIVOT INSTRUCTIONS OR DETAILS, SEE

PIVOT TEMPLATE. FOR USE WITH RIXSON PIVOT

MODEL 180 SERIES.

MINIMUM STOP THICKNESS 1/2".

1/8" DOOR TO SOFFIT CLEARANCE REQUIRED.

REINFORCING PER ANSI/SDI-100

RECOMMENDED FOR HOLLOW METAL DOORS

& FRAMES.

AUXILIARY STOP RECOMMENDED.

DO NOT SCALE DRAWING.

LEFT HAND DOOR AND CLOSER SHOWN.

RIGHT HAND OPPOSITE.

A REMOVABLE HEADSTOP MUST BE USED IN COMBINATION

WITH THE CLOSER FOR PROPER INSTALLATION. MOUNTING HOLES

FOR THE HEADSTOP MUST SPAN CLOSER LENGTH. HEADSTOP MUST BE

REMOVABLE TO INSTALL CLOSER AND MAKE PROPER ADJUSTMENTS.

PRODUCT:

TEMPLATE NUMBER:

DATE:

W91DCP OHC CLOSER

OC60937

5/2020

MODEL W91DCP OVERHEAD CONCEALED CLOSER

3/4" OFFSET PIVOT, WOOD FRAME

MAX. DEGREE OF OPENING

W91NDCP NON HOLD OPEN (115

)

W91NDCP NON HOLD OPEN WITH TRACK STOP

(105

)

W91HDCP HOLD OPEN (85

)

www.rixson.com

part without the express written permission of ASSA ABLOY Accessories and Door Controls Group, Inc. is prohibited.

"A" Dimension

Standard Appilcation

1" - 1/16" (27)

Retrofit Track Option

1" - 3/8" (35)

Andere Assa Abloy Türöffnungssystem Handbücher

Assa Abloy

Assa Abloy Norton 7570 Series Bedienungsanleitung

Assa Abloy

Assa Abloy RIXSON W50 Bedienungsanleitung

Assa Abloy

Assa Abloy Corbin Russwin PED5800 Series Bedienungsanleitung

Assa Abloy

Assa Abloy Norton 6300 Series Bedienungsanleitung

Assa Abloy

Assa Abloy NORTON RIXSON 6200 Series Bedienungsanleitung

Assa Abloy

Assa Abloy Corbin Russwin PED159 Bedienungsanleitung

Assa Abloy

Assa Abloy DC3210 Bedienungsanleitung

Assa Abloy

Assa Abloy Besam SL500 Bedienungsanleitung

Assa Abloy

Assa Abloy effeff 828 Bedienungsanleitung

Assa Abloy

Assa Abloy Corbin Russwin PED4200 Series Bedienungsanleitung

Assa Abloy

Assa Abloy Sargent Electroguard-59 80 Series Montageanleitung

Assa Abloy

Assa Abloy 281 Series Bedienungsanleitung

Assa Abloy

Assa Abloy 78PRA-8L Bedienungsanleitung

Assa Abloy

Assa Abloy CMD Bedienungsanleitung

Assa Abloy

Assa Abloy Adams Rite EX76W Betriebsanleitung

Assa Abloy

Assa Abloy Corbin Russwin ED7400 Series Bedienungsanleitung

Assa Abloy

Assa Abloy DC700G-FT Bedienungsanleitung

Assa Abloy

Assa Abloy effeff ePED 1386Z1LB7 04S0 Series Referenzhandbuch

Assa Abloy

Assa Abloy Besam SP33-M Bedienungsanleitung

Assa Abloy

Assa Abloy DC 700G-FT BGS Bedienungsanleitung

Assa Abloy

Assa Abloy Besam SL500 Bedienungsanleitung

Assa Abloy

Assa Abloy Norton PR1601 Bedienungsanleitung

Assa Abloy

Assa Abloy DC130 Bedienungsanleitung

Assa Abloy

Assa Abloy G-CO-FMS Bedienungsanleitung

Beliebte Türöffnungssystem Handbücher anderer Marken

Pamex

Pamex KT-INP35 Bedienungsanleitung

Cal-Royal

Cal-Royal N-F77CVR Bedienungsanleitung

Scrigno

Scrigno OPEN1000 Bedienungsanleitung

TriMark

TriMark UM 34 Bedienungsanleitung

BFT

BFT WIND RMB 130B 200 Bedienungsanleitung

Alecto

Alecto ADI-250 Bedienungsanleitung

Besam

Besam Swingmaster MP Leitfaden

CRL

CRL SENIOR PRIMA Bedienungsanleitung

GAL

GAL MOVFR Technisches Datenblatt

Normstahl

Normstahl IDO7 Bedienungsanleitung

Häfele

Häfele Finetta T 70 VF Bedienungsanleitung

AGS

AGS D-PL Handbuch

Stanley

Stanley MA900ñ Montageanleitung

WITTUR

WITTUR Hydra Plus UD300 Handbuch

Alutech

Alutech TR-3019-230E-ICU Montage- und Bedienungsanleitung

MPC

MPC ATD ACTUATOR 50 ATD-313186 Operating and Technisches Datenblatt

GEZE

GEZE ECturn Bedienungsanleitung

Chamberlain

Chamberlain T Bedienungsanleitung