Assa Abloy Corbin Russwin ED7400 Series Bedienungsanleitung

FM463 1/23

Installation Instructions

ED7400 Series

Surface Vertical Rod Exit Device

WARNING

This product can expose you to

lead which is known to the state of

California to cause cancer and birth

defects or other reproductive harm.

For more information go to www.

P65warnings.ca.gov.

Attention Installer: Improper

installation may result in damage

to the product and void the factory

warranty.

WARNING

For installation assistance contact Corbin Russwin

1-800-543-3658 • techsupport.corbinrusswin@assaabloy.com

Reproduction in whole or in part without the express written permission of ASSA ABLOY Access

and Egress Hardware Group, Inc. is prohibited.

ED7400 Series

Installation Instructions

Surface Vertical Rod Exit Device

For installation assistance contact Corbin Russwin

1-800-543-3658 • techsupport.corbinrusswin@assaabloy.com

Reproduction in whole or in part without the express written permission of ASSA ABLOY Access

and Egress Hardware Group, Inc. is prohibited.

FM463 1/23

1Screw Guide

Screw Guide

Screw Wood Door Metal Door

ATop Strike

#12 Round Head WS

#12-24 Pan Head Machine

Screws

B1/4-20 Binding Head Machine Screw and 7/16" Sex

Nut

C 1/4-20 Oval Head Mach Screw and 7/16" Sex Nut

D #12 Round Head WS #12 Round Head Tapping

Screw (Use 5/32" drill)

E #12 Round Head WS #12 Round Head Tapping

Screw (Use 5/32" drill)

F 1/4-20 Oval Head Mach Screw and 7/16" Sex Nut*

G 1/4-20 Oval Head Mach Screw and 7/16" Sex Nut*

H #12 Round Head WS #12 Round Head Tapping

Screw (Use 5/32" drill)

I #12 Round Head WS #12 Round Head Tapping

Screw (Use 5/32" drill)

J1/4-20 Binding Head Machine Screw and 7/16" Sex

Nut

K #14 Oval Head WS 1/4-20 Oval Head Self Tap-

ping (Use #3 drill)

LSurface Bottom Strike

#14 Flat Head WS

1/4-20 Flat Head Mach

Screws x 3415 Star Anchor

or equiv.

MFlush Bottom Strike

#14 Flat Head WS

1/4-20 Flat Head Mach

Screws x 3415 Star Anchor

or equiv.

Figure 1

*Sex Nut not required if outside trim used.

ED7400 Series

Installation Instructions

Surface Vertical Rod Exit Device

For installation assistance contact Corbin Russwin

1-800-543-3658 • techsupport.corbinrusswin@assaabloy.com

Reproduction in whole or in part without the express written permission of ASSA ABLOY Access

and Egress Hardware Group, Inc. is prohibited.

FM463 1/23

2Locate All Inside Holes on Centerline

Spot and drill holes B to J for screws

and sex nuts (as listed in screw guide -

Figure 1 on page 2). (Figure 2) SPOT G

FIRST.

NOTE: 13/16" (21mm) minimum

distance between stop and centerline

with single doors. With pair of doors,

1-3/16" (30) minimum centerline to

edge of door.

NOTE: If you have outside operator and

trim, use case mounting holes F and G

to locate trim template.

STOP

LDOOR

DOOR

STOP

7/8

(22)

Cut top

rod to this

length.

Single

Doors

13/16

(21)

Min.

(To Stop)

Pair of

Doors

1-3/16

(30)

Min.

(To Door

Edge)

(127)

2-1/16

(52)

1-1/2

(38)

3/4

(19)

1-5/8

(41)

1-11/16

(43)

(152)

CAUTION

Make 1-1/4" (32) deep

cutout only for an outside

operator.

(76)

3-5/8

(92)

WOOD DOORS ONLY

For lever handle trim -

Mortise this area

1-1/4 (32) deep.

38-5/8

(981)

(178)

SPOT “G”

HOLE FIRST

DO NOT DRILL

“K” HOLE

See step 11

L M N

FINISHED

FLOOR

Surface

Strike

Flush

Strike Threshold

OR OR

2-1/8

(54)

1-5/8

(41)

2-1/2

(63.5)

Figure 2

ED7400 Series

Installation Instructions

Surface Vertical Rod Exit Device

For installation assistance contact Corbin Russwin

1-800-543-3658 • techsupport.corbinrusswin@assaabloy.com

Reproduction in whole or in part without the express written permission of ASSA ABLOY Access

and Egress Hardware Group, Inc. is prohibited.

FM463 1/23

3Mount Top and Bottom Strikes

4Cut and Assemble Top Rod

5Insert Rod Guides - Position Top Rod

Using centerline established on door, close door and mount strikes against

door.

NOTE: Except for ﬂush bottom strike. See drawing for position. (Figure 3)

5/16

(8)

Figure 3

1. Measure distance from bottom

screw hole “C” of top latch case

to top screw hole “F” in active

case.

(Figure 2 on page 3)

2. Cut undrilled end of top rod to

this length.

3. Seat adjustable rod connector as

shown in cut end of rod. (Figure

4. Using hole as guide, drill through

connector and rod. Figure 4

Hammer

pin ﬂush

with head.

Back of Rod

Shown

Connector

Hole

Back of Rod

Shown

Connector

Hole

Side of Rod

Shown

Expansion

Rivet

Figure 5

1. Install 4 top and bottom rod guides exactly on

centerline. (D, E, H, I; Figure 2 on page 3)

2. Seat screw but do not crush guide.

3. Rotate guide “D” so track is horizontal.

(Figure 6)

DOOR

STOP

Top Rod Guides

Top Rod

90°

Figure 6

Track

Guide

Rod

Figure 7

5. Secure with expansion rivet from front of rod. (Figure 5)

4. Slip top rod over guide and rotate to vertical position, sliding rod down over guide “E”. (Figure 7)

ED7400 Series

Installation Instructions

Surface Vertical Rod Exit Device

For installation assistance contact Corbin Russwin

1-800-543-3658 • techsupport.corbinrusswin@assaabloy.com

Reproduction in whole or in part without the express written permission of ASSA ABLOY Access

and Egress Hardware Group, Inc. is prohibited.

FM463 1/23

6Mount Top Latch Frame

7Mount Bottom Rod

8Mount Active Case and Attach Rods

Retract latch and secure case with screw “B”. (Figure 8)

Figure 8

1. Position case so that pins in back engage holes in top and bottom rods. (Figure 11)

2. Secure with screws F and G. (Figure 1 on page 2)

NOTE: If you have outside trim follow template furnished.

TO REVERSE HAND:

1. Remove two (2) screws from back of each case to separate bodies from covers.

2. Switch covers and reassemble.

Top Rod

Bottom Rod

Figure 11

1. Turn guide “I” so track is horizontal. (Figure 9)

2. Slip bottom rod over guide and rotate to vertical position, sliding rod up over guide “H”. (Figure 10)

DOOR

STOP

Bottom Rod Guides

Bottom Rod

90°

Track

Guide

Rod

Figure 9 Figure 10

ED7400 Series

Installation Instructions

Surface Vertical Rod Exit Device

For installation assistance contact Corbin Russwin

1-800-543-3658 • techsupport.corbinrusswin@assaabloy.com

Reproduction in whole or in part without the express written permission of ASSA ABLOY Access

and Egress Hardware Group, Inc. is prohibited.

FM463 1/23

9Mount Active Case and Attach Rods

1. Slide bar through active and inactive case with 3/16” hole towards active case. Secure with 10-24 x

3/4” cap screw. (Figure 12)

Alternately push down on one lever

while pushing up on other.

NOTE: If levers do not work freely, check for binding of levers due to improper bar length or case

misalignment.

Figure 14

Figure 15

Figure 13

Figure 12

2. Mark bar at inactive case and cut. (Figure 13) Length of crossbar

should be ﬂush to 1/16” less than ﬂush from face of crossbar arm.

3. Drill 3/16” hole through one side of bar using hole in arm to locate. (Figure 14)

4. Assemble bar and end plug to the inactive case arm

with 10-24 x 3/4” cap screw.

ED7400 Series

Installation Instructions

Surface Vertical Rod Exit Device

For installation assistance contact Corbin Russwin

1-800-543-3658 • techsupport.corbinrusswin@assaabloy.com

Reproduction in whole or in part without the express written permission of ASSA ABLOY Access

and Egress Hardware Group, Inc. is prohibited.

FM463 1/23

Figure 17

10 Adjust Top Latch

11 Mount Bottom Latch Frame

1. Insert screw “J” through slot in frame into

bottom hole. (Figure 18)

2. Position frame so that latch just engages strike.

(Figure 19)

3. Tighten bottom screw.

4. Using hole “K” in frame as a guide, drill door

through hole in frame.

5. Insert screw “K”.

Figure 16

DO NOT

TIGHTEN

SCREW

Tighten screw.

Bolt engages strike.

Drill hole.

1. Shut door.

2. Turn adjustable rod connector until head touches underside

of slide. (Figure 16)

3. Insert pin. (Figure 17)

4. Depress crossbar.

5. If latch does not retract completely, remove pin and turn

connector out one (1) turn.

6. Repeat until latch bolt just disengages.

NOTE: For maximum security, do not over-adjust.

Tu r n

Adjustable

Connector

adjust.

Insert

in hole

thru

slot.

Figure 18 Figure 19

FM463 1/23

For installation assistance contact Corbin Russwin

1-800-543-3658 • techsupport.corbinrusswin@assaabloy.com

Reproduction in whole or in part without the express written permission of ASSA ABLOY Access

and Egress Hardware Group, Inc. is prohibited.

13 Test Operation

Latches should tightly engage strikes in closed position.

If door can be pushed open without depressing crossbar, top rod connector has been over-adjusted. See

Step 10.

When crossbar is depressed, latches should freely disengage strikes.

When active and inactive cases are dogged down, latches should disengage strikes.

If not, remove top and bottom latch cases and readjust adjustable rod connectors. See Steps 10 and 12.

12 Adjust Bottom Rod Length & Engage Latch

1. Dog down active case.

2. Turn adjustable rod connector so that latch bolt is ﬂush with

bottom of frame. (Figure 20)

3. Insert pin in adjustable rod connector. (Figure 21)

4. Undog active case.

Tu r n

Adjustable

Connector

adjust.

Figure 20 Figure 21

Insert

when

ﬂush.

13 Mount Latch Covers

Bottom

1. Position bottom latch cover above bottom latch frame and slide down

to engage spring. (Figure 22)

2. Secure with furnished screw.

Top

1. Position and secure with screw through bottom hole in frame.

Spring

engages

lip.

Figure 22

Inhaltsverzeichnis

Andere Assa Abloy Türöffnungssystem Handbücher

Assa Abloy

Assa Abloy Norton 6300 Series Bedienungsanleitung

Assa Abloy

Assa Abloy Norton 8000 Series Bedienungsanleitung

Assa Abloy

Assa Abloy Norton 9500 Series Bedienungsanleitung

Assa Abloy

Assa Abloy ABLOY DA401 Bedienungsanleitung

Assa Abloy

Assa Abloy Besam SW200i Bedienungsanleitung

Assa Abloy

Assa Abloy Norton 6300 Series Bedienungsanleitung

Assa Abloy

Assa Abloy RIXSON SMOK-CHEK V 0101 Bedienungsanleitung

Assa Abloy

Assa Abloy SW100 Bedienungsanleitung

Assa Abloy

Assa Abloy Corbin Russwin ED4000 Series Bedienungsanleitung

Assa Abloy

Assa Abloy UNION DoorSense 8755A Bedienungsanleitung

Assa Abloy

Assa Abloy Yale 2500 Series Bedienungsanleitung

Assa Abloy

Assa Abloy NORTON RIXSON 6300 Series Bedienungsanleitung

Assa Abloy

Assa Abloy SARGENT 1130 Series Bedienungsanleitung

Assa Abloy

Assa Abloy Corbin Russwin PED5800 Series Bedienungsanleitung

Assa Abloy

Assa Abloy Sargent Electroguard-59 80 Series Montageanleitung

Assa Abloy

Assa Abloy DC640 Bedienungsanleitung

Assa Abloy

Assa Abloy Corbin Russwin PED5000 DB Series Bedienungsanleitung

Assa Abloy

Assa Abloy Besam SW300 Handbuch

Assa Abloy

Assa Abloy Norton 5700 Series Kurzanleitung

Assa Abloy

Assa Abloy Yale 1105 Bedienungsanleitung

Assa Abloy

Assa Abloy Besam SW300 Bedienungsanleitung

Assa Abloy

Assa Abloy Norton 6300 Series Kurzanleitung

Assa Abloy

Assa Abloy 5800 ADAEZ PRO Bedienungsanleitung

Assa Abloy

Assa Abloy Corbin Russwin PED5400 FE Bedienungsanleitung

Beliebte Türöffnungssystem Handbücher anderer Marken

Pamex

Pamex KT-INP35 Bedienungsanleitung

Cal-Royal

Cal-Royal N-F77CVR Bedienungsanleitung

Scrigno

Scrigno OPEN1000 Bedienungsanleitung

TriMark

TriMark UM 34 Bedienungsanleitung

BFT

BFT WIND RMB 130B 200 Bedienungsanleitung

Alecto

Alecto ADI-250 Bedienungsanleitung

Besam

Besam Swingmaster MP Leitfaden

CRL

CRL SENIOR PRIMA Bedienungsanleitung

GAL

GAL MOVFR Technisches Datenblatt

Normstahl

Normstahl IDO7 Bedienungsanleitung

Häfele

Häfele Finetta T 70 VF Bedienungsanleitung

AGS

AGS D-PL Handbuch

Stanley

Stanley MA900ñ Montageanleitung

WITTUR

WITTUR Hydra Plus UD300 Handbuch

Alutech

Alutech TR-3019-230E-ICU Montage- und Bedienungsanleitung

MPC

MPC ATD ACTUATOR 50 ATD-313186 Operating and Technisches Datenblatt

GEZE

GEZE ECturn Bedienungsanleitung

Chamberlain

Chamberlain T Bedienungsanleitung