Assa Abloy Sargent Electroguard-59 80 Series Montageanleitung

Installation and Wiring

Instructions For Electroguard®59-

Prefix 80 Series Exit Device to

ElectroLynx Connector System

For installation assistance, contact SARGENT at 800-810-WIRE (9473)

A7690C

3/08

A7690C.indd 1 11/8/18 9:01 AM

800-810-WIRE (9473) • www.sargentlock.com • A7690C

Reproduction in whole or in part without the express written permission of SARGENT Manufacturing is prohibited.

Table of Contents

General Description............................................................. 1

Parts Breakdown ................................................................. 1

Recent Product Enhancement to Aid Installation &

Adjustments......................................................................... 2

Optional Equipment............................................................. 3

Sample Elevation Diagram ................................................. 3

Cylinder Installation ............................................................. 4

Electroguard™Dip Switch Settings ...................................... 5

Basic Installation Instructions.............................................. 6

Exit Device Installation ................................................... 7-17

Exit Device Plug-in Connector Installation ........................ 18

Electroguard™Input/Output Diagram................................. 19

Electrical Specifications..................................................... 19

Input/Output Descriptions.................................................. 20

System Wiring Examples ............................................. 21-24

Operating Instructions .................................................. 25-27

Additional Features ........................................................... 27

Care of Finish Guide ......................................................... 28

Electroguard™Troubleshooting .................................... 29-33

ElectroLynx®

As part of their promise to provide innovative, fast and effective,

and higher security solutions to their customers, ASSA ABLOY

Group companies offer ElectroLynx, a universal quick-connect

system that simplifies the electrification of the door opening.

ElectroLynx®is a registered trademark of ASSA ABLOY, Inc.

A7690C.indd 2 11/8/18 9:01 AM

A7690C • 800-810-WIRE (9473) • www.sargentlock.com

Reproduction in whole or in part without the express written permission of SARGENT Manufacturing is prohibited.

NOTE: Field cut rail assemblies are not allowed. Exit Device must be ordered for specific 80 series type, specific door width

and finish from the factory. Consult factory with any questions @ 800-810-WIRE (9473).

The SARGENT 59- Electroguard™ is designed for areas which require a delayed egress requiring an alarm at the door when

any attempt is made to violate the door. The Electroguard™ can be tied into a fire alarm system, indicate latchbolt status and

control an alarm at a remote location when the door is in violation.

NOTE: Proper connections and appropriate peripheral hardware is required.

Part No. Description

52-2994 59- Circuit Board Replacement Kit for “F” size rails (Includes one 52-2558 circuit board and

“

F” size rail harness)

52-2995 59- Circuit Board Replacement Kit for “J” size rails (Includes one 52-2558 circuit board and

“J” size rail harness)

52-2996 59- Circuit Board Replacement Kit for “G” size rails (Includes one 52-2558 circuit board and

“G” size rail harness)

52-2558 Electroguard™ Circuit Board only

52-2204 Latchbolt Harness and Switch Assembly for 59-8800 and 8500 Rim Devices

52-2217 Surface Vertical Rod Harness and Switch Assembly for 59-8700 Devices

52-2220 Concealed Vertical Rod Harness and Switch Assembly for 59-8600 and 8400 Devices

52-2224 Latchbolt Harness and Switch Assembly for 59-8900 and 8300 Mortise Devices

Mounting rail

insert

Mounting

plate

Endcap

Circuit board

Cover

Chassis

assembly

Switch

assembly

Exit Device

Chassis Assembly

and Rail Assembly

Electroguard™

Circuitry

1” diameter hole required for

routing wires into the door Manual dogging is

provided standard on

non fire rated devices

General Description

Parts Breakdown

A7690C.indd 1 11/8/18 9:01 AM

2800-810-WIRE (9473) • www.sargentlock.com • A7690C

Reproduction in whole or in part without the express written permission of SARGENT Manufacturing is prohibited.

IMPORTANT

When servicing previous versions using circuit boards with 16-pin connector/harness, you must refer to Installation Manual A7043

for wiring and functional differences. Portions of the Troubleshooting section within this manual may be used for previous version

circuit boards

Plug-in connector system updates

New circuit board with 4 diagnostic LEDs with plug-in connector harness

• Standardized wire colors and connector terminations

• Separate 5-pin (J1) and 9-pin (J2) input harnesses. This

simplifies wiring terminations in most applications since

most applications require only the 5-pin harness

• Standard wire colors on 5-pin and 9-pin input harnesses.

IMPORTANT: Some wire colors have been changed from

previous version 59- circuit board

• 4 diagnostic LEDs for installation and troubleshooting

assistance:

Yellow LED – Indicates Latchbolt or Vertical Rod switch status

Green LED – Indicates whether the Rail Magnet is energized or

de-energized

Red LED – Indicates whether the Push Rail (REX) Switch is

activated or de-activated

Orange LED – Monitors the Door Status Switch position when

switch is being used

• Visible Yellow Insert LED has been eliminated. The Red LED

flashes now to indicate momentary egress

• Added wire for earth ground termination

• 16 position rotary switch has been changed to Dip Switch–

S2. Positions 3 and 4 are now used to select momentary

egress times

• Voice and Ganged features are now jumper selectable

• Red Visible Insert LED is ON to indicate fire alarm condition

rather than the Green Visible Insert LED

• Nuisance Delay is now 1 second (was 2 seconds)

Electroguard plug-in connector harness

5 & 9-pin to 8 & 4-pin connectors

8-pin

connector

4-pin

connector

3 loose wires

GREEN LED

RED LED

HORN

JP1

JP2

JP3

JP4

Two Insert LEDs

JP1

JP2

JP3

JP4

Harness with 5 and 9 pin connectors

and loose wires

Two Insert LEDs

S3 1234

YELLOW

LED

GREEN

LED

RED

LED

16 16

16-pin

connector

Harness with 16-pin connector

and loose wires

Recent Product Enhancements to Aid

Installation and Adjustment

New circuit board with 4 diagnostic LEDs*

*Shipped after 2/29/04

Circuit board with 16-pin connector and no diagnostic LEDs*

*Shipped prior to 2/29/04

A7690C.indd 2 11/8/18 9:01 AM

A7690C • 800-810-WIRE (9473) • www.sargentlock.com

Reproduction in whole or in part without the express written permission of SARGENT Manufacturing is prohibited.

1. Determine locations of components at the door

2. Mountallhardwareandperipheralequipmentaccordingtomanufacturer’sinstructions

3. Power supply should be mounted near door to avoid power drop due to excessive wire runs

4. Features used will determine wire requirements of electric hinge or other power transfer*

123

456

789

SARGENT

(Ordered Separately)

CAUTION!!

There are no user serviceable parts on the Electroguard™ Circuit Board. Consult parts breakdown for new Electroguard™ Circuit

Board.

There are two switches in the device: a latchbolt or vertical rod switch, and request to exit switch. Both are preset at the factory.

Tampering or breaking switches will cause malfunction.

All components must be installed according to prevailing electrical codes.

3510, 3530, 3560

Power supplies

TA2714 CC4

TA714 CC12

Electric hinge

3071/3072

Voice module

4291/4292

Keypad

4371LT

Key switch

3287

Door status switch

123

456

789

Page 5 Art

Optional Equipment

Sample Elevation Diagram

A7690C.indd 3 11/8/18 9:01 AM

4800-810-WIRE (9473) • www.sargentlock.com • A7690C

Reproduction in whole or in part without the express written permission of SARGENT Manufacturing is prohibited.

1. Prepare door according to template and instruction sheet supplied with exit device

2. Verify 1-1/8” mortise cylinder (size 41) is installed in rail insert with collar prior to installing exit

device on door

TO ADD OR REMOVE CYLINDER

1. Ensure power is disconnected

2. Separate circuit board and ground wire from mounting insert by

removing the four (4) screws from the under side

3. Once separated, slide cylinder through

collar into the insert as shown

NOTE: Orientation of the cylinder

Secure the cylinder with cylinder nut.

Tighten firmly

4. Re-attach circuit board and ground wire

to mounting insert with four (4) screws

5. Operate cylinder and verify cam is

operating switch properly

SARGENT

Collar

Cylinder Nut

DIP Switches

Top View

(LHRB shown)

Side View

Cam (cam engages switch)

SARGENT

Collar

Cylinder

Insert

Cylinder nut

Cylinder Installation

ORIENTATION OF CYLINDER

A7690C.indd 4 11/8/18 9:01 AM

A7690C • 800-810-WIRE (9473) • www.sargentlock.com

Reproduction in whole or in part without the express written permission of SARGENT Manufacturing is prohibited.

Dip switch positions 3 and 4 - Used to select the momentary egress time of 5, 10, 20 or 40 seconds. This switch is preset at

the factory for five seconds

S2 Dip Switch Position Momentary

Egress Time

3 4

OFF OFF 5

seconds

OFF ON 10

seconds

ON OFF 20

seconds

ON ON 40

seconds

S2-1 Nuisance Delay - (Field selectable 0 or 1 second) A one second nuisance delay can be enabled by setting Dip

Switch (S2-1) to the On position. When nuisance delay is enabled, the unit will require the push bar to be depressed

for more than one second in order to trigger an irreversible alarm condition. If the push bar is released before the 1

second has elapsed, the unit will go back into the “delayed egress mode” and the alarm will not sound. Nuisance

delay is set to On position at factory

If the Dip Switch S2-1 is in the Off position, there will be no nuisance delay and alarm horn will sound

immediately when the push bar is depressed

S2-2 Nuisance Audible - (Field selectable on or off) An audible horn is enabled by setting Dip Switch S2-2 to the On

position. The internal horn will sound as soon as the push bar is depressed, signaling that the device is armed. If the

pushbar is held down for more than 1 second, an irreversible alarm condition begins. If Dip Switch S2-2 is in the Off

position, the horn will not sound during nuisance delay

Nuisance audible is set to On position at factory to sound horn when rail is depressed during nuisance delay

OFF

S2-1 On - 1 second nuisance delay

S2-1 Off - no nuisance delay

S2-2 On - Nuisance Audible On

S2-2 Off - Nuisance Audible Off

OFF

S2-1

Select Dip Switch Settings prior to installing exit device on door

Electroguard™ Dip Switch Settings

S2-2

A7690C.indd 5 11/8/18 9:01 AM

6800-810-WIRE (9473) • www.sargentlock.com • A7690C

Reproduction in whole or in part without the express written permission of SARGENT Manufacturing is prohibited.

Inside

View of Door

Verify hand and bevel of door. Exit devices are always reverse bevel and are mounted on the inside of the door.

On inside of door, exit devices are oriented as follows:

8800 RHRB shown

Lights from top to bottom:

Red, Green

8800 LHRB shown

Lights from top to bottom:

Green, Red

Outside View Outside view

Inside View Inside view

Basic Installation Instructions

A7690C.indd 6 11/8/18 9:01 AM

A7690C • 800-810-WIRE (9473) • www.sargentlock.com

Reproduction in whole or in part without the express written permission of SARGENT Manufacturing is prohibited.

Exit Device Installation

Electroguard (59-, 12-59-)

80 Series Rail

with 8 and 4-pin connectors

and 3 loose wires

3 1

1, Violet (RAR - NC)

2, Grey (LBM - C)

4, Tan (LBM - NC)

3, Pink (LBM - NO)

Red/Green (Voice/Gang - C)

1, Black (-24)

2, Red (+24)

4, Green (EG)

3, White (FA)

5, Orange (EI)

7, Brown (RAR - C)

8, Yellow (RAR - NO)

6, Blue (DS)

Red/Black (Voice/Gang - NC)

Red/Yellow (Voice/Gang - NO)

Note: RAR, LBM and Voice/Gang contacts

shown are with power applied to rail

B. ElectroLynx Connector System Notes:

The system is designed to be installation friendly with

pluggable connectors from the electric hinge through the

door to the rail. The only wiring required is to the loose

wires on the pigtail harness assembly on the frame side

of the electric hinge

IMPORTANT:

The plug and receptacle connectors are designed to

mate and lock together as shown in the figure. Plug the

connectors into each other with the locking mechanism

aligned as indicated

Do NOT force connectors on any other way

A. IMPORTANT

Caution: Disconnect all input power before beginning installation to prevent electrical

shock and equipment damage

1. Installer must be a trained, experienced service person

2. All wiring must comply with applicable local electrical codes, ordinances and regulations

3. Field cut rail assemblies are not allowed. Exit device must be ordered for specific door width

Plug

Locking mechanism

Receptacle

A7690C.indd 7 11/8/18 9:01 AM

8800-810-WIRE (9473) • www.sargentlock.com • A7690C

Reproduction in whole or in part without the express written permission of SARGENT Manufacturing is prohibited.

C. Installation Notes:

1. With new applications, a raceway harness with 8 & 4-pin connectors will be pre-installed inside the door by ASSA ABLOY

door manufacturer when specified during the ordering process. Raceway harness kits are also available for retrofit

applications. For retrofit applications, refer to retrofit instructions

2. If door does not have a raceway harness with connectors, either consult factory for raceway retrofit kit or cut connectors off

product and hard wire, as required

3. Wiring to pigtail harness is per facility wiring requirement. The rail, raceway, electric hinge and pigtail connector terminations

and wire colors all match

Exit Device Installation (continued)

Installing 59-8300/12-59-8300 Series Mortise Lock Exit Device

CAUTION – BEFORE STARTING:

• Check hand of door (This exit device is handed and not reversible)

• Door should be fitted and hung

• Verify box label for size of exit device, function and hand

PREPARE DOOR AND MOUNT LOCK –

Refer to Instruction Sheet A6696

1. Feed wire and connector through the mortise opening

and out the inside diameter

Rail wire &

connector

Wire &

connector

Chassis Wire holder

Chassis

arm

Vertical reference line C

Lchassis

Mortise lock body

Left hand reverse

bevel illustrated

Inside Of

Door

IMPORTANT: Surface of door where exit

device is to be applied must be flush.

Clear away any raised projections to allow

exit device to rest on flat surface of door

Cover

8400 Main Chassis Cover Dwg

8300 Mount Lock Dwg

Wire & connector Inside

diameter

Rail assembly

General Touch Bar

Lock Down Key —7/32” hex key

To operate: Depress pushrail,

insert hex key and turn clockwise.

(Not furnished with 12-)

Push rail

A7690C.indd 8 11/8/18 9:01 AM

Inhaltsverzeichnis

Andere Assa Abloy Türöffnungssystem Handbücher

Assa Abloy

Assa Abloy effeff ePED 1386Z1LB7 04S0 Series Referenzhandbuch

Assa Abloy

Assa Abloy Norton 7500 Series Bedienungsanleitung

Assa Abloy

Assa Abloy Norton 9540 Series Bedienungsanleitung

Assa Abloy

Assa Abloy RIXSON 91DCP Bedienungsanleitung

Assa Abloy

Assa Abloy SARGENT 278 Series Bedienungsanleitung

Assa Abloy

Assa Abloy Corbin Russwin DC3210 Series Bedienungsanleitung

Assa Abloy

Assa Abloy Besam SL500 Bedienungsanleitung

Assa Abloy

Assa Abloy Norton 6011 Series Bedienungsanleitung

Assa Abloy

Assa Abloy Adams Rite EX88 Betriebsanleitung

Assa Abloy

Assa Abloy Norton J1600 UniTrol Bedienungsanleitung

Assa Abloy

Assa Abloy Pando Mini Go Bedienungsanleitung

Assa Abloy

Assa Abloy Sargent 1331 Bedienungsanleitung

Assa Abloy

Assa Abloy NORTON RIXSON 6200 Series Bedienungsanleitung

Assa Abloy

Assa Abloy effeff 828 Bedienungsanleitung

Assa Abloy

Assa Abloy Norton 5500 Series Bedienungsanleitung

Assa Abloy

Assa Abloy Norton 78-B/FHA Hold Open Series Bedienungsanleitung

Assa Abloy

Assa Abloy Norton 5900 Series Kurzanleitung

Assa Abloy

Assa Abloy Corbin Russwin ED5400 (A) Series Bedienungsanleitung

Assa Abloy

Assa Abloy Corbin Russwin PED4000 Series Bedienungsanleitung

Assa Abloy

Assa Abloy SW100 Bedienungsanleitung

Assa Abloy

Assa Abloy RIXSON W50 Bedienungsanleitung

Assa Abloy

Assa Abloy Norton 1600 UniTrol Bedienungsanleitung

Assa Abloy

Assa Abloy CloserPlus Ramp Norton XF460 Bedienungsanleitung

Assa Abloy

Assa Abloy DC700 Bedienungsanleitung

Beliebte Türöffnungssystem Handbücher anderer Marken

Pamex

Pamex KT-INP35 Bedienungsanleitung

Cal-Royal

Cal-Royal N-F77CVR Bedienungsanleitung

Scrigno

Scrigno OPEN1000 Bedienungsanleitung

TriMark

TriMark UM 34 Bedienungsanleitung

BFT

BFT WIND RMB 130B 200 Bedienungsanleitung

Alecto

Alecto ADI-250 Bedienungsanleitung

Besam

Besam Swingmaster MP Leitfaden

CRL

CRL SENIOR PRIMA Bedienungsanleitung

GAL

GAL MOVFR Technisches Datenblatt

Normstahl

Normstahl IDO7 Bedienungsanleitung

Häfele

Häfele Finetta T 70 VF Bedienungsanleitung

AGS

AGS D-PL Handbuch

Stanley

Stanley MA900ñ Montageanleitung

WITTUR

WITTUR Hydra Plus UD300 Handbuch

Alutech

Alutech TR-3019-230E-ICU Montage- und Bedienungsanleitung

MPC

MPC ATD ACTUATOR 50 ATD-313186 Operating and Technisches Datenblatt

GEZE

GEZE ECturn Bedienungsanleitung

Chamberlain

Chamberlain T Bedienungsanleitung