AT&T Merlin Legend 10BS Bedienungsanleitung

The BRI (Basic Rate Interface) Access button is a button programmed on any of the first ten

buttons on your telephone. Using this button, you can use BRI features available through your

local telephone company, known as the central office or CO.

Similar to the MERLIN LEGEND Trunk-to-Trunk Transfer feature, the Central Office (CO) Transfer

feature allows you to connect the caller to a branch office in a distant office or redirect a local or

long-distance misdialed number to the correct number. By using the BRI Access button to dial the

destination station of your call, the BRI lines to the MERLIN LEGEND system are available for

additional in-coming calls and call hand

ling. In addition to the CO Transfer feature, the BRI Access

button also identifies the last line used for a call for use with the Local Area Signaling Services

(LASS) features. The LASS features provide you with call management capabilities:

●

Automatic Callback

●

Automatic RecalI

Note:

Depending on your CO, the names of these features and their feature codes, and the

voice prompts you hear may vary.

Each of these features can be activated on any multi-line telephone with a Personal Line button

for the BRI line on which the call was placed or received. However, use of the LASS features is

not recommended in a pool environment.

Note:

There can be only one BRI Access button on a telephone.

Check with your system administrator that your telephone has been programmed to use the

BRI Access button features. Procedures for using each of these features follow.

BRI Access Button

Quick

Reference

CO Transfer

With the CO Transfer feature using BRI lines, your line is available following the completion of the transfer

and is not used for the duration of the call,

Procedure

To transfer a call outside of the MERLIN LEGEND system using the BRI Access button:

1. While a call on a BRI line is in progress, press the

Transfer

button,

The call is placed on hold, The system automaticalfy selects a System Access (SA) or Intercom (ICOM)

Voice or Ring button.

2.. Press the

BRI Access

button, The red and green LEDs next to the BRI Access button lights,

The green LED next to the line button with the held call flutters to indicate the call is on hold, You receive

a dial tone. The caller outside being transferred hears silence while the call is being connected,

3. Dial the outside telephone number,

Note:

Do not use Automatic Route Selection (ARS) or pool dial-out code to dial the outside number.

Depending on your CO, you may need to dial

to access an outside line.

—If you receive no answer or a busy signal at the destination telephone number you can return to the

call being held for transfer by pressing the line button associated with that call. This action removes

the transfer request and connects you with the origins/ call.

4. When the destination party answers the call, press the

Transfer

button or hang up to complete the transfer,

—Depending on your CO, the party to receive the transferred call, may need to answer or the call may

be disconnected,

The LEDs next to the BRI line and the BRI Access button go off to indicate that both line buttons are

available for use.

BRI

Access

Button Quick Reference

Automatic Callback

With the Callback feature, you can automatically

place a call to the last telephone number called to

a BRI Personal Line, even if the caller’s number is

unknown,

Procedure

Follow these steps:

1. With the telephone receiver off-hook, press

the

Personal Line

button,

The Personal Line green LED lights,

You receive a dial tone.

Proceed to step 4.

If more than one BRI line is assigned as a

Personal Line button and you do not know

which Personal Line button was used to

receive the last call, follow steps 2 and 3:

If your telephone is an MLX display set, press

the

BRI Access

button. You receive the

display: Dial 4 for In; 6 for Out. Dial 4 which

represents the letter “l” for incoming calls,

The red LED (which represents the MERLIN

LEGEND Idle Line Preference feature) moves

to the last Personal Line button used to

receive an incoming call on a BRI line.

The green LED next to the BRI Access Button

goes off.

Lift the receiver, or if the telephone is

4. Dial the

feature code

to activate the

Callback feature.

The telephone number from which the last

call was received on the BRI line is

automatically dialed by the CO.

— If the telephone number being called is

available, you hear ringback, Identify

yourself to the party called.

— If the number is busy the CO “camps” or

queues the call at the called number When

the number is available, the CO calls you

back on the BRI line used to place the call.

All telephones sharing the Personal Line

button ring with a priority ring (four-burst

ring for MLX sets; three-burst ring for

analog multiline phones) to indicate the

completed call.

equipped with a speakerphone, press the

Speakerphone

button.

The green LED lights.

You receive a dial tone.

Proceed to step 4.

BRI

Access

Button Quick Reference

With the Recall feature, you can automatically

place a call to the last telephone number called

from a BRl Personal Line without manually

redialing the number,

Procedure

Follow these steps:

1. With the telephone receiver off-hook, press

the

Personal Line

button.

The Personal Line green LED lights,

You receive a dial tone,

Proceed to step 4.

If more than one BRI line is assigned as a

Personal Line button and you do not know

which Personal Line button was used to make

the last call, follow steps 2 and 3:

If you telephone is an MLX( display set, press

the

BRI Access

button, You receive the

display: Dial 4 for In; 6 for Out. Dial 6 which

represents the letter “O” for outgoing calls,

The red LED moves to the last Personal Line

button used to make an outgoing call

(excluding calls made on a BRI Access button

to initiate a CO-based transfer).

The green LED next to the BRI Access Button

goes off.

Lift the receiver, or if the telephone is

equipped with a speakerphone, press the

Speakerphone

button.

The green LED lights,

You receive a dial tone,

Proceed to step 4.

Dial the

feature code

to activate the Recall

feature, The telephone number from which the

last call was received on the BRI line is

automatically dialed by the CO.

—If the telephone number being called is

available, you hear ringback. Identify

yourself to the party called.

— If the number is busy the CO “camps” or

queues the call at the called number When

the number is available, the CO calls you

back on the BRI line used to place the call.

All telephones sharing the Personal Line

button ring with a priority ring (four-burst

ring for MLX sets; three-burst ring for

analog multiline phones) to indicate the

completed call.

Andere Handbücher für Merlin Legend 10BS

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere AT&T Konferenzsystem Handbücher

AT&T

AT&T Merlin 1030 Technisches Handbuch

AT&T

AT&T MERLIN LEGEND Release 2.0 Analog Multiline... Betriebsanleitung

AT&T

AT&T MERLIN 820 Bedienungsanleitung

AT&T

AT&T Merlin II Handbuch

AT&T

AT&T Merlin 3070 Bedienungsanleitung

AT&T

AT&T MERLIN LEGEND Release 2.0 MLX Queued Call... Handbuch

AT&T

AT&T MERLIN 206 Bedienungsanleitung

AT&T

AT&T Merlin 1030 Bedienungsanleitung

AT&T

AT&T Spirit Communications System Bedienungsanleitung

AT&T

AT&T Lucent Technologies PARTNER Plus Kurzanleitung

AT&T

AT&T Partner Plus Bedienungsanleitung

AT&T

AT&T Merlin Legend BIS22D Bedienungsanleitung

AT&T

AT&T DEFINITY 2500 series Montage- und Wartungsanleitung

AT&T

AT&T MERLIN LEGEND Release 2.0 Analog Direct-Line... Handbuch

AT&T

AT&T Merlin II Benutzerhandbuch

AT&T

AT&T MERLIN LEGEND Release 2.0 Analog Multiline... Betriebsanleitung

AT&T

AT&T MERLIN 410 Bedienungsanleitung

AT&T

AT&T Merlin 3070 Bedienungsanleitung

AT&T

AT&T MERLIN 410 Stücklistenhandbuch

AT&T

AT&T MERLIN LEGEND Communications System Key System Planning Forms... Technisches Handbuch

AT&T

AT&T Partner Plus Installationsanleitung

AT&T

AT&T Merlin Legend MLX-20L Bedienungsanleitung

AT&T

AT&T MERLIN 206 Stücklistenhandbuch

AT&T

AT&T MERLIN Plus Benutzerhandbuch

Beliebte Konferenzsystem Handbücher anderer Marken

Kramer

Kramer VIA GO Bedienungsanleitung

ProSoft Technology

ProSoft Technology AN-X4-AB-DHRIO Bedienungsanleitung

Sony

Sony PCS-I150 Bedienungsanleitung

Middle Atlantic Products

Middle Atlantic Products VTC Series Bedienungsanleitung

AVT

AVT MAGIC AC1 Go Bedienungsanleitung

Prentke Romich Company

Prentke Romich Company Vanguard Plus Leitfaden

Speakerbus

Speakerbus iD 712 Bedienungsanleitung

Trelleborg

Trelleborg SafePilot CAT PRO Bedienungsanleitung

Sennheiser

Sennheiser ADN Bedienungsanleitung

ADTRAN

ADTRAN NetVanta 7100 Bedienungsanleitung

AINA

AINA PTT Voice Responder Bedienungsanleitung

Yamaha

Yamaha ProjectPhone PJP-100H Bedienungsanleitung

vissonic

vissonic VLI Series Bedienungsanleitung

Panasonic

Panasonic KX-VC500 Bedienungsanleitung

Poly

Poly Trio 8300 Bedienungsanleitung

Crestron

Crestron Mercury CCS-UCA-SMK Maßzeichnung

Tenveo

Tenveo ALL-IN-ONE Bedienungsanleitung

AXIWI

AXIWI AT-350 Bedienungsanleitung