Atdec 8060 Bedienungsanleitung

AD-WT-8060 Page 1 of 4

Installation Guide

AD-WT-8060

Tilt Wall Mount 8060

IMPORTANT INFORMATION

! Please ensure this product is installed as per these installation instructions.

! The manufacturer accepts no responsibility for incorrect installation.

! Failure to mount this product correctly may cause serious injury/death during or following installation.

! This product is not suitable for outdoor use.

! Do not use this product for mobile applications.

! Wall Plate only achieves maximum weight rating when appropriately fastened to a wall of adequate structural capacity.

! Professional installer to ensure adequate structural capacity of wall (including appropriate safety factor) to support total

weight of all equipment being mounted.

! Drilling into electrical wires can cause death - use appropriate equipment and caution when drilling holes in walls to avoid

electrical cables, water pipes and gas pipes. Do not drill into structures unless you have established it’s safe to do so.

M-C

M6x30

Screw

(x4)

M-B

M6x14

Screw

(x4)

M-D

M8x30

Screw

(x4)

M-A

M5x14

Screw

(x4)

M-F

Multi

Washer

(x4)

M-G

Short

Spacer

(x8)

M-E

M8x50

Screw

(x4)

Display Bracket (left)

Display Bracket (right)

Wall Plate

Security Bar

M-H

Long

Spacer

(x8)

Hex Key

REQUIRED TOOLS

• Phillips head screwdriver

• Power drill

• Suitable drill bit

• Driver bit for selected

wall fasteners

• Stud nder

• Spirit level

• Socket wrench set

COMPONENT CHECKLIST

0 - 80kg

(0 - 176lb)

WEIGHT RANGE

NOTE:

! Wall Plate Mounting Fasteners are NOT supplied with Wall Mounts.

Professional installer to ensure correct Mounting Fastener type, location &

quantity to suit structure where Wall Mount is installed.

! ALWAYS use a washer between the chosen fastener and the wall plate.

! Mounting fasteners to be used as per manufacturers instructions, including

minimum engagement to achieve necessary performance.

AD-WT-8060 Page 2 of 4

Slot Dimension

Ø8 x 40mm

12 3

3. Hook and Secure the Display onto the Wall Plate

Max. Ø11 mm

NOTE:

Ensure level adjustment

screws are retracted prior

to mounting the display.

3.1. Angle the display and hook the Display

Brackets over the top of the Wall Plate.

This should be completed by two people.

NOTE:

• Choice and supply of appropriate wall plate fasteners is the

responsibility of the installer.

• Consult a preferred fastener supplier or a structural engineer

to select fasteners which are most appropriate for the weight

of the display and wall construction method.

• Wall plate must be level. Verify using a quality spirit level tool.

• On a Stud Wall or Drywall use a good quality Stud Finder to

position mounting fasteners in the centre of studs.

• On a Masonry Wall avoid positioning Wall Plate mounting

fasteners in a mortar join.

M-C (M6x30) /

M-D (M8x30)

M-C (M6x30) /

M-D (M8x30)

M-F

M-G M-G

M-H

M-G

M-H

M-H M-G

M-H

M-C (M6x30) /

M-D (M8x30)

M-E (M8x50) M-E (M8x50) M-E (M8x50)

M-A (M5x14) /

M-B (M6x14)

M-F M-F M-F

M-H (OPTIONAL)

SPACER HEIGHT (mm)

M-G (OPTIONAL)

M-A

M-B

M-C

M-D

M-E

(M5x14)

(M6x14)

(M6x30)

(M8x30)

(M8x50)

M-F

403530

2520

2. Attach the Display Brackets to the Display

3.2. Slide Security Bar Dthrough the slots at the bottom of each

Display Bracket, ensuring the Security Bar sits to the rear of

the Wall Plate and the display cannot be lifted up and off the

Wall Plate.

3.3. (OPTIONAL) To prevent theft of the display, add a padlock to

the end of Security Bar D.

1. Mount the Wall Plate to the Wall

Slot Dimension

Ø9 x 55mm

*Fasteners shown are for example only

NOTE:

• Always use multi-washers M-F.

• Ensure the display brackets are

not loose and screws are not

forced too deep into the display.

• If spacers are needed, use the

shortest possible combination

between the display bracket and

the display.

AD-WT-8060 Page 3 of 4

+5° / -10°

Remove the black plastic caps

from Display Brackets Band C.

Tilt the display to the desired

viewing angle and tighten the

nuts using a suitable socket

wrench tool to lock the angle

in place.

NOTE:

Support display whilst adjusting tilt.

NOTE:

Support display whilst turning the level adjustment screws.

Level Adjustment Display Tilt

+5° / -10°

ADJUSTMENTS

If needed, carefully turn the

screws at the top of each

display bracket clockwise using

Hex Key Eto level the display.

AD-WT-8060 Page 4 of 4

No portion of this document or any artwork contained herein should be reproduced in any way without

the express written consent of Atdec Pty Ltd. Due to continuing product development, the manufacturer

Andere Atdec Rack & Stand Handbücher

Atdec

Atdec AF-MC Bedienungsanleitung

Atdec

Atdec AWMS-2-BT75-FS Bedienungsanleitung

Atdec

Atdec AD-TVC-70R Bedienungsanleitung

Atdec

Atdec AWM-A13 Bedienungsanleitung

Atdec

Atdec Telehook Bedienungsanleitung

Atdec

Atdec Levitate L-PB Bedienungsanleitung

Atdec

Atdec AWM-P G Bedienungsanleitung

Atdec

Atdec TELEHOOK 12/30 Multi Bedienungsanleitung

Atdec

Atdec AWM-A13-B Bedienungsanleitung

Atdec

Atdec VFS-DV Bedienungsanleitung

Atdec

Atdec Visidec Focus Micro Betriebsanleitung

Atdec

Atdec ADBS-2x1-17TC Bedienungsanleitung

Atdec

Atdec AWM 710 Arm Bedienungsanleitung

Atdec

Atdec Levitate Betriebsanleitung

Atdec

Atdec Visidec Focus Articulated Arm Wall Betriebsanleitung

Atdec

Atdec TH-1040-CTS Bedienungsanleitung

Atdec

Atdec AWM-LR Bedienungsanleitung

Atdec

Atdec AWMS-2-BT75-FS Bedienungsanleitung

Atdec

Atdec AF-ATC Bedienungsanleitung

Atdec

Atdec AWM-W35 Bedienungsanleitung

Atdec

Atdec VISIDEC FOCUS MICRO Betriebsanleitung

Atdec

Atdec Telehook Bedienungsanleitung

Atdec

Atdec AF-M Bedienungsanleitung

Atdec

Atdec AWM-BT Bedienungsanleitung

Beliebte Rack & Stand Handbücher anderer Marken

Salamander

Salamander Acadia AC/W/L400/WH Bedienungsanleitung

Fohhn

Fohhn VAT-09 Benutzerhandbuch

ricoo

ricoo FS0522 Bedienungsanleitung

AMSOIL

AMSOIL BMK-22 Kurzanleitung

Kargo Master

Kargo Master 48220 Bedienungsanleitung

Milestone AV Technologies

Milestone AV Technologies SIMPLICITY SLF2 Bedienungsanleitung

ricoo

ricoo S1222 Bedienungsanleitung

Ready-Set-Mount

Ready-Set-Mount RSMCM602 Bedienungsanleitung

VidaBox

VidaBox VB MNT FFS2 Bedienungsanleitung

Welch Allyn

Welch Allyn 48960 Bedienungsanleitung

Arkon

Arkon CM035-ST-2 Bedienungsanleitung

PROEL

PROEL PLWIN60C Bedienungsanleitung

Agilent Technologies

Agilent Technologies E2609B Bedienungsanleitung

Mustang

Mustang MV-ARM4 Bedienungsanleitung

Mounting Solutions

Mounting Solutions WRM-320 Bedienungsanleitung

Pyle

Pyle PMKSPAD1 Bedienungsanleitung

ShelterIt

ShelterIt 21208 Bedienungsanleitung

SPL

SPL RackPack?4 1040 Bedienungsanleitung