Atdec TH-1040-CTS Bedienungsanleitung

Component Checklist

Mounting Plate

Pole Assembly

VESA Plate

Mounting Plate Cover

Coach Screw (x4)

Nylon Anchor (x4)

M4/5/10 Washer

(x4 each)

Set Screw

M6/8 Spacer (x4)

M4/5 Spacer (x4)

(optional) Security Screw

2.5/3/5mm

Allen Key

Pole Assembly

Mounting Plate Cover

PUSH

Screw Pole Assembly

into Mounting Plate by

twisting top half of the

Pole Assembly only.

Pole

Assembly

Mounting Plate

TWIST

3mm

Allen Key

Set Screw

Insert Set Screw into the

Mounting Plate to lock the

Pole Assembly in position.

Pole Assembly

Mounting Plate

Cover

PUSH

TH-1040-CTS

TH-1040-CTL

IMPORTANT INFORMATION:

Step 1. Check Components

Check you have received all parts against the Component Checklist and Hardware above.

Step 2. Install Mounting Plate

Step 4.

Attach Pole Assembly to Mounting Plate

! IMPORTANT - Install 1040 Ceiling Tilt Mount (Short/Long) as per Installation Instructions.

! This product supports a maximum load of 25kg (55lbs).

! This product supports VESA mounting hole conﬁgurations 75x75mm, 100x100mm, 200x100mm, 200x200mm.

! The manufacturer accepts no responsibility for incorrect installation.

Step 5. Position Mounting Plate Cover

Step 3. Install Mounting Plate Cover

Hardware

Tools Required:

Power drill

•

7mm

(¼”)

drill bit

•

12mm

(½”)

masonry drill bit

•

Phillips head screw driver•

17mm (11/16”) Socket Wrench or Shifter

•

Masonry Ceiling

Timber Ceiling

Using the Mounting

Plate

as a template, mark

out

and drill

4x Ø7mm

(¼”)

holes,

Ø12mm

(½”)

for masonry

ceilings,

70mm (2.75”) deep.

Nylon Anchor

Mounting Plate

Coach Screw

M10 Washer

False Ceiling Cover

TH-1040-CTSW

TH-1040-CTLW

M4x16/25mm (x4 each)

M5x16/25mm (x4 each)

M6x16/30mm (x4 each)

M8x16/30mm (x4 each)

Display Mounting

Screws

Ceiling Tilt Short Mount / Ceiling Tilt Long Mount

Installation Instructions

Set Screw

Cable

Access Port

Installation Complete

No portion of this document or any artwork contained herein should be reproduced in any way without the express written consent of Atdec Pty Ltd.

Due to continuing product development, the manufacturer reserves the right to alter speciﬁcations without noticed. Published 05.02.16 ©

Step 6. Set Height of Pole

Step 9. Cable Management

Whilst supporting the lower half of Pole

Assembly loosen

the

Socket Cap Screws (x2).

Slide Pole Assembly

to the desired height.

Tighten the Socket Cap

Screws (x2) to set the height.

Step 8. Attach Display to Pole Assembly

Feed cables down the Pole

Assembly through the Cable

Access Port.

Pull cables out from lower

half of the Pole Assembly

and

connect to Display.

Step 10. Height Adjustment

Pole Joint

LOOSEN

TIGHTEN

FIRMLY

Socket Cap

Screw

5mm Allen Key

ADJUST

HEIGHT

Loosen Socket Cap

Screws (x2) on the Donut.

TILT

PAN

Step 7. Attach VESA Plate to Display

TOP

Step 11. Final Adjustment

A. Pan,

Tilt and Rotate

the Display as

required.

If necessary, centralise the

Pole Joint by tightening the

Set Screws (x2) to suit.

2.5mm

Allen Key

VESA plate

Mounting

Screws

B. Slide

the height of the

Donut

as required. Tighten

Socket Cap Screws to lock.

Step 12. Install False Ceiling Cover

PORTRAIT TO

LANDSCAPE

Choose the appropriate

mounting hardware to suit the Display.

Spacers

(optional, for recessed

mounting holes)

B. PUSH

HOOK

(optional) Once Display

is attached, insert

Security Screw using

Phillips-head screwdriver

Security

Screw

Socket Cap

Screw

5mm

Allen Key

VESA Ball Mount

Tension Plate at rear

3mm Allen Key

If necessary tighten the VESA

Ball

Mount by adjusting the

Tension Plate. Using the 3mm

Allen Key adjust screws evenly.

Donut

SLIDE

False Ceiling

Cover

CLICK

Lower Pole

If the Lower Pole hangs below a suspended ceiling, clip the False

Ceiling Cover over the Lower Pole, and push up to the ceiling.

PUSH

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Atdec Rack & Stand Handbücher

Atdec

Atdec Telehook Bedienungsanleitung

Atdec

Atdec AWM-W6 Bedienungsanleitung

Atdec

Atdec AWM-FC Bedienungsanleitung

Atdec

Atdec VFS-DH Bedienungsanleitung

Atdec

Atdec Telehook Bedienungsanleitung

Atdec

Atdec AD-WM-5060 Bedienungsanleitung

Atdec

Atdec AWMS-2-BT75-G Bedienungsanleitung

Atdec

Atdec TELEHOOK 12/30 Multi Bedienungsanleitung

Atdec

Atdec AD-WM-7060 Bedienungsanleitung

Atdec

Atdec AWM 460 Arm Bedienungsanleitung

Atdec

Atdec Spacedec SD-POS-VBM-B2B Bedienungsanleitung

Atdec

Atdec AWM-W35 Bedienungsanleitung

Atdec

Atdec AWMS-BT40 Bedienungsanleitung

Atdec

Atdec AWM-A13-B Bedienungsanleitung

Atdec

Atdec ADB-FS Bedienungsanleitung

Atdec

Atdec Levitate Betriebsanleitung

Atdec

Atdec ADBS-2x1-17TC Bedienungsanleitung

Atdec

Atdec TH-3060-UF Bedienungsanleitung

Atdec

Atdec AF-AT-NBC Bedienungsanleitung

Atdec

Atdec AWM-AD Bedienungsanleitung

Atdec

Atdec Visidec Focus Micro Bedienungsanleitung

Atdec

Atdec 8060 Bedienungsanleitung

Atdec

Atdec AWM-LR Bedienungsanleitung

Atdec

Atdec AD-TVC-45 Bedienungsanleitung

Beliebte Rack & Stand Handbücher anderer Marken

Salamander

Salamander Acadia AC/W/L400/WH Bedienungsanleitung

Fohhn

Fohhn VAT-09 Benutzerhandbuch

ricoo

ricoo FS0522 Bedienungsanleitung

AMSOIL

AMSOIL BMK-22 Kurzanleitung

Kargo Master

Kargo Master 48220 Bedienungsanleitung

Milestone AV Technologies

Milestone AV Technologies SIMPLICITY SLF2 Bedienungsanleitung

ricoo

ricoo S1222 Bedienungsanleitung

Ready-Set-Mount

Ready-Set-Mount RSMCM602 Bedienungsanleitung

VidaBox

VidaBox VB MNT FFS2 Bedienungsanleitung

Welch Allyn

Welch Allyn 48960 Bedienungsanleitung

Arkon

Arkon CM035-ST-2 Bedienungsanleitung

PROEL

PROEL PLWIN60C Bedienungsanleitung

Agilent Technologies

Agilent Technologies E2609B Bedienungsanleitung

Mustang

Mustang MV-ARM4 Bedienungsanleitung

Mounting Solutions

Mounting Solutions WRM-320 Bedienungsanleitung

Pyle

Pyle PMKSPAD1 Bedienungsanleitung

ShelterIt

ShelterIt 21208 Bedienungsanleitung

SPL

SPL RackPack?4 1040 Bedienungsanleitung