Atdec AWM-A71-B Bedienungsanleitung

AWM-A71 Page 1 of 4

Installation Guide

AWM-A71

710 Arm

COMPONENT CHECKLIST

Monitor Arm

(x1)

VESA Head

(x1)

Screw

M4x25mm

(x4)

Screw

M4x16mm

(x4)

Screw

M4x12mm

(x4)

Spacer

(x4)

Security

screw

(x1)

4mm

allen key

(x1)

Post Clamp

(x1)

REQUIRED TOOLS

WEIGHT RANGE

• Phillips Head Screwdriver

Flat Monitors

0 - 9kg

(0 - 20lbs)

Curved Monitors

0 - 8kg

(0 - 17.6lbs)

Monitor weight should be within the

weight range of all modular elements

that make up the complete monitor

mounting solution.

IMPORTANT INFORMATION

! Please ensure this product is installed as per these installation instructions.

! The manufacturer accepts no responsibility for incorrect installation.

! This product is compatible with Atdec AWM Series products.

! Curved monitors, deep devices (such as all-in-one PCs) and offset VESA locations exert additional leverage that can exceed the

capacity of the mount even though the monitor weight may be within the stated range. Please contact Atdec if you would like further

information.

AWM-A71 Page 2 of 4

3. Place the rotation ring

in the desired postion

2. Set arm rotation to 180° (optional)

2.1 Remove plastic sleeve

from post clamp.

2.2 Remove rotation ring. 2.3 Place rotation ring in

desired position.

Note: rotation ring placement

depends on the position of the clamp

on the post. The tag on the ring

should always face toward the user.

1. Remove plastic sleeve

2. Remove rotation ring

1. Press

2. Lift

Note rotation is set to 360� by default.

180°

360°

Default

Position

Flipped

Position

Tag

1. Fix clamp to Post or Wall Channel

1.1 Ensure knob is undone. 1.2 Slide post clamp into channel.

Push knob to

aid insertion

1.3 Hold clamp in desired position on

channel and turn knob to lock in place.

1. Ensure Knob is undone

Tip: push knob

to aid insertion

2. Slide post clamp into channel

3. Hold clamp in desired position on post and turn

knob to lock in place

3. Fit arm onto post clamp

Note: Check the

arm rotation is

smooth after

tightening.

3.1 Push arm onto shaft. 3.2 Ensure arm is fully pushed onto shaft. 3.3 Tighten joint screw.

1. Push arm onto clamp

2. Ensure arm is fully pushed onto clamp

3. Tighten set screw

Tip: Check the

arm rotation is

smooth after

tightening.

AWM-A71 Page 3 of 4

5. Mount monitor

6. Adjust tilt tension & Install security screw

Gap No gap

Monitor arm

5.2 Ensure that the VESA head sits flush within

the monitor arm. There should be no gap.

6.1 Use the allen key to adjust the tilt tension until the monitor

holds in a vertical position at the end of the arm.

Note: Support

monitor while

adjusting.

6.2 OPTIONAL security screw

To install the optional security screw tilt the head upwards

Tighten

Loosen

Tighten

Loosen

5.1 Insert VESA head into the monitor arm 5.3 Push the lever down to

secure monitor to the arm

assembly

4. Attach VESA head to monitor

100mm

75mm

100mm 75mm

Flush

Too long Too short

Spacer

5mm 12mm

4.2 Screw the VESA head onto monitor

Note spacers may be required for curved,

recessed or uneven monitor surfaces.

4.3 Ensure the correct screw length is used

to attach the monitor.

4.1 VESA mounting compatibility

100mm

75mm

100mm 75mm

Flush

Too long Too short

Spacer

5mm 12mm

Note: For other sizes, use a suitable

adaptor plate (sold separately).

AWM-A71 Page 4 of 4

7. Monitor arm cable management

Note: The cable cover shown

does not come with all posts

8.4 To reposition the cable cover, pull it

straight up and out of the post and insert

it into any of the available channels

Cable cover

Cable

Cover

Desk

Clamp

8.1 Push the cable down into the cable clip

Note: Cable clips do not

come with all posts

8.6 Feed remaining cable into cover8.5 Loop cable and insert into cable cover

8.2 Push cable clip into post channel

8. Post cable management

atdec.com | atdec.co.uk | atdec.com.au

No portion of this document or any artwork contained herein should be reproduced in any way without

the express written consent of Atdec Pty Ltd. Due to continuing product development, the manufacturer

8.3 Recommended post cable cover

position for double or triple arm set-ups

7.1 Plug cables into the

monitor and route the

cables down the arm

using the cable hooks

and clips.

Important:

Ensure enough cable slack is given

to allow for movement of the monitor

Alternative cable

cover positions

Dieses Handbuch passt für folgende Modelle

Andere Atdec Rack & Stand Handbücher

Atdec

Atdec AWM-BT Bedienungsanleitung

Atdec

Atdec AWMS-DW6 Bedienungsanleitung

Atdec

Atdec AWMS-2-BT75-FS Bedienungsanleitung

Atdec

Atdec AF-M Bedienungsanleitung

Atdec

Atdec AWMS-2-LTH75-H Bedienungsanleitung

Atdec

Atdec Levitate L-PB Bedienungsanleitung

Atdec

Atdec TH-1040-CTS Bedienungsanleitung

Atdec

Atdec VFS-Q Bedienungsanleitung

Atdec

Atdec AF Series Bedienungsanleitung

Atdec

Atdec AWM-A71 Bedienungsanleitung

Atdec

Atdec AWMS-2-BT75-G Bedienungsanleitung

Atdec

Atdec AWMS-2-BT75-G Bedienungsanleitung

Atdec

Atdec TELEHOOK TH-3060-UT Bedienungsanleitung

Atdec

Atdec ADBS-2x2-17MFB Bedienungsanleitung

Atdec

Atdec AD-TVAC-CM Bedienungsanleitung

Atdec

Atdec Visidec Focus Articulated Arm Wall Betriebsanleitung

Atdec

Atdec TH-3060-UFL Bedienungsanleitung

Atdec

Atdec Freestanding Quad Bedienungsanleitung

Atdec

Atdec AWM-LC Bedienungsanleitung

Atdec

Atdec ADBS-4x1-39TW Merkblatt

Atdec

Atdec SYSTEMA SW6S Bedienungsanleitung

Atdec

Atdec VF-AT-NP Bedienungsanleitung

Atdec

Atdec AWM-W35 Bedienungsanleitung

Atdec

Atdec AWMS-2-D13-C Bedienungsanleitung

Beliebte Rack & Stand Handbücher anderer Marken

Salamander

Salamander Acadia AC/W/L400/WH Bedienungsanleitung

Fohhn

Fohhn VAT-09 Benutzerhandbuch

ricoo

ricoo FS0522 Bedienungsanleitung

AMSOIL

AMSOIL BMK-22 Kurzanleitung

Kargo Master

Kargo Master 48220 Bedienungsanleitung

Milestone AV Technologies

Milestone AV Technologies SIMPLICITY SLF2 Bedienungsanleitung

ricoo

ricoo S1222 Bedienungsanleitung

Ready-Set-Mount

Ready-Set-Mount RSMCM602 Bedienungsanleitung

VidaBox

VidaBox VB MNT FFS2 Bedienungsanleitung

Welch Allyn

Welch Allyn 48960 Bedienungsanleitung

Arkon

Arkon CM035-ST-2 Bedienungsanleitung

PROEL

PROEL PLWIN60C Bedienungsanleitung

Agilent Technologies

Agilent Technologies E2609B Bedienungsanleitung

Mustang

Mustang MV-ARM4 Bedienungsanleitung

Mounting Solutions

Mounting Solutions WRM-320 Bedienungsanleitung

Pyle

Pyle PMKSPAD1 Bedienungsanleitung

ShelterIt

ShelterIt 21208 Bedienungsanleitung

SPL

SPL RackPack?4 1040 Bedienungsanleitung