Atdec SPACEDEC ACROBAT Betriebsanleitung

Please do not

remove card from the

Spacedec Acrobat

Articulated Wall Arm

For your comfort and safety please take a few

moments to adjust the position of your display

To adjust the Spacedec Acrobat Articulated

Wall Arm, please refer to the instructions in

this User Operating Card

Use the Ergonomic Guidelines overleaf

as a guide for correct positioning

Depending on the weight of the display, it may be

necessary to make adjustments to the Ball Joint

Mechanism. If the display doesn’t hold its position

or is too resistant, adjust the four tension screws

located around the Ball Joint (see diagram) using

the supplied 2.5mm Allen Key.

Check the display, and then adjust again if

necessary.

NOTE: Be sure to adjust screws evenly.

Tighten

Loosen

Tension

Screws (x4)

Ball Joint

2.5mm

Allen Key

It is possible to control the amount of resistance

in the Pivot Head to suit your display.

To increase the resistance of the Pivot Head to

suit heavier displays, use the 5mm Allen Key

supplied in the Desk Clamp Box to tighten the

interscrew in a clockwise direction.

To decrease the resistance of the Pivot Head to

suit lighter displays, loosen the interscrew in an

anti-clockwise direction.

NOTE: It is recommended the Pivot

Head be left at the factory setting for

best performance.

Pivot Head

Interscrew

5mm Allen Key

Loosen

Tighten

Lighter

display

Heavier

display

Raise Gas Strut

to suit lighter

display

Arm

5mm

Allen key

Gas Strut

Lighter

Heavier

Lower Gas Strut to

suit heavier display

B.3.1 Depending on the weight of the display,

it may be necessary to adjust the arm. This can

be done by using the supplied 5mm Allen Key.

B.3.2. If the arm tends to automatically rise

or fall when the display is attached, it will be

necessary to make small adjustments to the gas

strut. (see diagram)

B.3.3. If the arm tends to rise, the gas strut

position should be raised. If the arm tends to

fall, the gas strut position should be lowered.

B.1. Adjusting Ball Joint friction

B.2. Adjusting Pivot Head tension

B.3. Adjusting Gas Strut Resistance

USER

OPERATING CARD

SPACEDEC ACROBAT

ARTICULATED WALL ARM

15°

5°

HORIZONTAL SIGHT LINE (d)

CENTRE OF SCREEN

10°-20°

(h)

Adjusting Display

Due to continuing product development, the manufacturer

reserves the right to alter specifications without notice.

Ergonomic Guidelines

Ergonomists recommend that the optimal position of your screen should be slightly below eye level.

When looking at the screen’s centre the user should have a downward visual angle of approx. 10°-20°.

As a guide, the height (h) of your display should be approximately as follows:

Tall Male (Max): 560mm (22”) Tall Female (Max): 520mm (201/2”)

Short Male (Min): 368mm (141/2”) Short Female (Min): 356mm (14”)

For visual comfort, a viewing distance (d) between 500mm (20”) to 750mm (291/2”) is recommended.

Angular adjustments to reduce reflection on your display should range between 5° forward tilt to 15°

backward tilt.

Mechanical Adjustment

If undesired tilt or pan occurs at any stage, this means the factory settings on your Articulated Wall

Arm requires adjustment. Please refer to adjustment details overleaf.

B.1. Ball Joint friction

B.2. Pivot Head tension

B.3. Gas Strut resistance

Your Articulated Wall Arm should already be preset to accommodate the average

size/weight of a display. To adjust the position of your display for visual comfort,

simply hold both sides of the display and adjust to desired position.

Published: 24.10.07©

atdec.com

SPACEDEC ACROBAT

ARTICULATED WALL ARM

B.1.

B.2.

B.3.

Andere Atdec Rack & Stand Handbücher

Atdec

Atdec AWM-A71-B Bedienungsanleitung

Atdec

Atdec AWMS-2-BT75-G Bedienungsanleitung

Atdec

Atdec AWMS-2-BT75-FS Bedienungsanleitung

Atdec

Atdec AWM Series Bedienungsanleitung

Atdec

Atdec SD-AT-DW Bedienungsanleitung

Atdec

Atdec AWM-LTH Bedienungsanleitung

Atdec

Atdec AWM-AD Bedienungsanleitung

Atdec

Atdec VFS-DV Bedienungsanleitung

Atdec

Atdec AWMS-2-BT75-G Bedienungsanleitung

Atdec

Atdec ADBS-4x1-39TW Merkblatt

Atdec

Atdec VFS-Q Bedienungsanleitung

Atdec

Atdec AWM-A13-B Bedienungsanleitung

Atdec

Atdec TH-1040-CTS Bedienungsanleitung

Atdec

Atdec AWMS-BT40 Bedienungsanleitung

Atdec

Atdec Telehook Bedienungsanleitung

Atdec

Atdec TH-1040-CTS Bedienungsanleitung

Atdec

Atdec AF-AA Bedienungsanleitung

Atdec

Atdec AWM-P G Bedienungsanleitung

Atdec

Atdec AD-AC-PH Bedienungsanleitung

Atdec

Atdec TH-3060-UFL Bedienungsanleitung

Atdec

Atdec Freestanding Quad Bedienungsanleitung

Atdec

Atdec AWM-X40 Bedienungsanleitung

Atdec

Atdec AWM-W35 Bedienungsanleitung

Atdec

Atdec AWM 710 Arm Bedienungsanleitung

Beliebte Rack & Stand Handbücher anderer Marken

Salamander

Salamander Acadia AC/W/L400/WH Bedienungsanleitung

Fohhn

Fohhn VAT-09 Benutzerhandbuch

ricoo

ricoo FS0522 Bedienungsanleitung

AMSOIL

AMSOIL BMK-22 Kurzanleitung

Kargo Master

Kargo Master 48220 Bedienungsanleitung

Milestone AV Technologies

Milestone AV Technologies SIMPLICITY SLF2 Bedienungsanleitung

ricoo

ricoo S1222 Bedienungsanleitung

Ready-Set-Mount

Ready-Set-Mount RSMCM602 Bedienungsanleitung

VidaBox

VidaBox VB MNT FFS2 Bedienungsanleitung

Welch Allyn

Welch Allyn 48960 Bedienungsanleitung

Arkon

Arkon CM035-ST-2 Bedienungsanleitung

PROEL

PROEL PLWIN60C Bedienungsanleitung

Agilent Technologies

Agilent Technologies E2609B Bedienungsanleitung

Mustang

Mustang MV-ARM4 Bedienungsanleitung

Mounting Solutions

Mounting Solutions WRM-320 Bedienungsanleitung

Pyle

Pyle PMKSPAD1 Bedienungsanleitung

ShelterIt

ShelterIt 21208 Bedienungsanleitung

SPL

SPL RackPack?4 1040 Bedienungsanleitung