Audiovox Pursuit PRO-OE3 Betriebsanleitung

The transmitters included with the security system have been

pre-pro

grammed at the factory, with each button pre-assigned to control a

specific function of the security system. Although the security system in the

vehicle has eithera3or4channel receiver, depending on the model, the

transmitters included with the system are capable of transmitting 7 distinct

signals. This allows you to program each transmitter to more than one vehicle

in two car families, and also allows you to change which button(s) control

certain functions of the system.

( Example: Transmitter channel 5 can be programmed to activate Receiver

channel 2.) Refer to the chart below for access to each of the transmitter

channels, and for the standard factory button assignments.

TRANSMITTER SYSTEM RECEIVER

CHANNEL BUTTONS CHANNEL FUNCTION

1 ARM 1 **Remote Arm & Disarm

DISARM **Remote Emergency Panic

Remote Door Lock & Unlock

2 OPTION 1 2 * Pulsed Output for Accessories

3 OPTION 2 3 * Switched Output for Accessories

ARM 4 * Switched Output for Accessories

DISARM

OPTION 1

OPTION 2

ARM

DISARM

OPTION 2

7 ALL 3

BUTTONS

Model : PRO-OE3

TRANSMITTER PROGRAMMING GUIDE

Some of the more common accessories for these additional channels

are;

*AS 9554 Remote Garage Door Interface

*AS 9075 Remote car starter

*AS 9153 Remote window roll up

*AS 9256 Remote trunk release relay

** Only Available With Remote Alarm Systems

In addition to the information provided above, the PRO-OE3 transmitter is

capable of utilizing different transmitter Icon pads. These replacement pads

may be used with your transmitter, depending on the specific options that

may have been installed or added to your security/keyless entry system.

(If your transmitter appears more like one of the units shown on page 4 of

this manual, use the text reference along side the specific transmitter for

programming your unit).

PROGRAMMINGTHETRANSMITTERS

It is important to remember that during programming, each individual step of

the procedure must be executed within 15 seconds of the previous step.

When the 15 second time limit is allowed to expire, the system will

automatically terminate the programming mode. This is indicated by a long

chirp from the siren.

Additionally, the system will store codes from up to four different

transmitters. If a 5th transmitter is programmed to any receiver channel,

then the first transmitter programmed to that channel will be erased from

the system's memory.

Non alarm models will flash the parking lights only to confirm the transmitter

code has been learned and stored.

Transmitter PD 10 is referenced during the program procedure listed below.

To Program replacement or additional transmitters:

1. Enter the vehicle, and turn the ignition key to the " on " position.

2. Flip the valet switch "on" - "off" - "on" - "off" - "on" - then "off".

3. The dash L.E.D. will flash one time, and the sounding device will beep

one time, indicating the system is ready to accept programming for

receiver channel 1.

4. Press and hold the Arm/Disarm button for 4 seconds or until the sounding

device emits a long beep, indicating the signal has been stored into

memory.

5. If you have additional transmitters ( up to 4 ) that need to be programmed,

repeat step 4 for each transmitter.

6. Flip the valet switch "on" then "off".

7. The dash L.E.D. will flash two times, and the sounding device will beep

two times, indicating the system is ready to accept programming for

receiver channel 2.

8. Press and hold the Option 1 or Option 2 transmitter button(s)for4

seconds or until the sounding device emits a long beep, indicating the

signal has been stored into memory.

9. If you have additional transmitters ( up to 4 ) that need to be programmed,

repeat step 8 for each transmitter.

10. Flip the valet switch "on" then "off".

11. The dash L.E.D. will flash three times, and the sounding device will beep

three times, indicating the system is ready to accept programming for

receiver channel 3.

12. Press and hold the selected Option 1 or Option 2 transmitter button(s)for

4 seconds or until the sounding device emits a long beep, indicating the

signal has been stored into memory.

13. If you have additional transmitters ( up to 4 ) that need to be programmed,

repeat step 12 for each transmitter.

14. Flip the valet switch on then off.

15. The dash L.E.D. will flash four times, and the sounding device will beep four

times, indicating the system is ready to accept programming for receiver

channel 4.

16. Press and hold the remaining Option 1 or Option 2 transmitter button(s)

for 4 seconds or until the sounding device emits a long beep, indicating the

signal has been stored into memory.

17. If you have additional transmitters ( up to 4 ) that need to be programmed,

repeat step 16 for each transmitter.

18. Turn the ignition key off. The sounding device will emit one short beep

followed by one long beep indicating the system has terminated the program

mode.

TRANSMITTER BATTERY REPLACEMENT

You will notice a decrease in transmitter range as the battery condition

deteriorates. Transmitter battery replacement is recommended at least every

10 to 12 months, depending upon how frequently the transmitter is used.

The transmitter has a small red L.E.D. built into the case. This L.E.D. can be used

to indicate battery condition. If the L.E.D. does not illuminate, then the battery

is discharged, and must be replaced.

To replace the transmitter battery,

1. Remove the small phillips head screws

from the bottom cover of the transmitter.

2. Carefully unsnap the top cover of the

transmitter from the bottom cover.

3. Remove the discharged battery, making

note of the location of the + and - contacts,

and replace with a new type GP 27A 12

volt battery.

4. Replace the transmitter cover, taking care not to damage the L.E.D. or

switches on the circuit board, and secure with the small phillips head screw.

TRANSMITTERPD#10:

If your transmitter appears as the unit shown on the left, All

programing information listed on the previous pages apply.

TRANSMITTERPD#11:

If your transmitter appears as the unit shown on the left, for

programming, you would substitute the Icon for the ARM/

DISARM reference on page 2 during step 4.

TRANSMITTERPD#12:

If your transmitter appears as the unit shown on the left, for

programming, you would substitute the Icon for the

ARM/DISARM reference on page 2 during step 4.

Substitute the Icon for the OPTION reference on page 2 during

step 8.

TRANSMITTERPD#13:

If your transmitter appears as the unit shown on the left, for

programming, you would substitute the Icon for the ARM/

DISARM reference on page 2 during step 4.

Substitute the Icon for the OPTION reference on page 2 during

step 8. Substitute the Icon for the OPTION

reference on page 3 during step 12.

TRANSMITTERPD#14:

If your transmitter appears as the unit shown on the left, for

programming, you would substitute the Icon for the ARM/

DISARM reference on page 2 during step 4.

Substitute the Icon for the OPTION reference on page 2 during

step 8. Substitute the Icon for the OPTION

reference on page 3 during step 12.

ORDER FORM FOR 3 BUTTON TRANSMITTER

MODEL NO. PRO OE3

IMPORTANT : To help us expedite your order, please print all of the information

legibly, and mail this form and your payment according to the instructions

below.

1. Name : ____________________________________________________

Address : _____________________________________________________

City : _____________________ State : _______ Zip Code : ____________

2. Telephone Number : ( _______ ) _________________________________

3. Enter the total number of transmitters required here : ________________

4. List model number of your actual transmitter pad as shown on page

4 of this manual:

5. The cost per transmitter is $ 65.00.

6. Enter the total amount enclosed here : ____________________________

( New York state residents must include the appropriate sales tax.)

7. Method of payment; check one of the boxes below.

Mastercard Visa Check or money order*(donotsend cash )

* Make checks payable to Audiovox Corporation

8. Credit Card Number : ________________________________________

9. Credit Card Expiration Date : _____________________

Credit card purchasers can order additional or replacement

transmitters by phone. Simply dial 1 - 800 - 645 - 4994, and follow

the instructions from the operator interface.

10. Mail this form, and your check, to ;

AUDIOVOX CORPORATION

150 MARCUS BLVD. HAUPPAUGE, N.Y. 11788

Attn: Transmitter Ordering Department



Form No. 128-5309B

Inhaltsverzeichnis

Andere Audiovox Sender Handbücher

Audiovox

Audiovox Prestige APS-2K4 Betriebsanleitung

Audiovox

Audiovox PSI 95BT3 Betriebsanleitung

Audiovox

Audiovox Prestige APS-2K4 Betriebsanleitung

Audiovox

Audiovox Pursuit PRO-OE3B3 Betriebsanleitung

Audiovox

Audiovox Pursuit 093BPr Betriebsanleitung

Audiovox

Audiovox Pursuit Series Bedienungsanleitung

Audiovox

Audiovox Prestige 105BP Betriebsanleitung

Audiovox

Audiovox Prestige APS-2K4MS Betriebsanleitung

Audiovox

Audiovox PurSuit 091BPr Betriebsanleitung

Audiovox

Audiovox PRO-94FR Betriebsanleitung

Audiovox

Audiovox AVX01BT3CL3 Betriebsanleitung

Audiovox

Audiovox AA-99BT2 Betriebsanleitung

Audiovox

Audiovox AUTO SECURITY Prestige OE3B4 Betriebsanleitung

Audiovox

Audiovox 5BCR03A Betriebsanleitung

Audiovox

Audiovox PurSuit 08SPr Betriebsanleitung

Audiovox

Audiovox Pursuit 095BPr Betriebsanleitung

Audiovox

Audiovox ADDP1 Betriebsanleitung

Audiovox

Audiovox Prestige 101BP Betriebsanleitung

Audiovox

Audiovox APS 95 BT3S Betriebsanleitung

Audiovox

Audiovox AA923-AA94BT Betriebsanleitung

Audiovox

Audiovox PurSuit 09XR1Pr Betriebsanleitung

Audiovox

Audiovox Pursuit PRO-OE4 Betriebsanleitung

Audiovox

Audiovox Auto Security SS91 Betriebsanleitung

Audiovox

Audiovox Pursuit 095BPr Betriebsanleitung

Beliebte Sender Handbücher anderer Marken

NIVELCO

NIVELCO EasyTREK SCA-300 Series Betriebsanleitung

Honeywell

Honeywell 5816WMBR Bedienungsanleitung

Kamstrup

Kamstrup READy MTU Betriebsanleitung

Omega

Omega ZW Series Bedienungsanleitung

ABB

ABB Field 264H Leitfaden

Alinco

Alinco DJ-V17T Bedienungsanleitung

Dejero

Dejero EnGo 3x Bedienungsanleitung

Rosemount

Rosemount 4600 Bedienungsanleitung

Speaka Professional

Speaka Professional 2342740 Bedienungsanleitung

trubomat

trubomat GAB 1000 Bedienungsanleitung

Teledyne Analytical Instruments

Teledyne Analytical Instruments LXT-380 Bedienungsanleitung

Rondish

Rondish UT-11 Bedienungsanleitung

MG 10JRE Bedienungsanleitung

Burkert

Burkert 8177 Bedienungsanleitung

Firetide

Firetide HotPort 3203 Handbuch

Tele Radio

Tele Radio T9-02 Bedienungsanleitung

Rotronic

Rotronic HygroFlex HF3 Series Bedienungsanleitung

Jamara

Jamara FCX6 Pro Tel Bedienungsanleitung