Avenview FO-HDM-IP4K-SET Bedienungsanleitung

VIDEO WALLS VIDEO PROCESSORS

VIDEO MATRIX SWITCHES

EXTENDERS SPLITTERS WIRELESS

CABLES & ACCESSORIES

Control Your Video

HDMI Extender up to 20KM

over Fiber Optic with IR Support

The contents of this document are provided in connection with Avenview Inc. (“Avenview”) products. Avenview makes no representations or

warranties with respect to the accuracy or completeness of the contents of this publication and reserves the right to make changes to specifications

and product descriptions at any time without notice. No license, whether express, implied, or otherwise, to any intellectual property rights is granted

by this publication. Except as set forth in Avenview Standard Terms and Conditions of Sale, Avenview assumes no liability whatsoever, and disclaims

any express or implied warranty, relating to its products of Avenview Inc. is strictly prohibited.

Model #: FO-HDM-IP4K-SET

Military Residential

Medical Aviation

Education Industrial

Corporate House Of Worship

www.avenview.com

Product Application & Market Sectors

www.avenview.com Page 3

TABLE OF CONTENTS

1. IMPORTANT SAFEGUARDS..............................................................................................................1

1.1SAFETY INSTRUCTIONS ..................................................................................................................1

1.2REGULATORY NOTICES FEDERAL COMMUNICATIONS COMMISSION (FCC) ........................... 2

2. INTRODUCTION ..............................................................................................................................3

2.1 PACKAGE CONTENTS .....................................................................................................................4

2.2 BEFORE INSTALLATION...................................................................................................................4

2.4DEVICE DESCRIPTION & LAYOUT..................................................................................................7

2.4.1 Front Panel & Rear Panel (Transmitter, FO-HDM-IP4K-S).......................................................7

2.4.2 Front Panel & Rear Panel (Receiver, FO-HDM-IP4K-R) ............................................................8

3. INSTALLATION................................................................................................................................10

4. GENERAL TROUBLESHOOTING....................................................................................................10

5. SPECIFICATIONS..............................................................................................................................11

2.5 IR CONTROL DESCRIPTION, FO-HDM-IP4K-SET) .........................................................................9

2.3 APPLICATION DIAGRAM ..................................................................................................................5

5. PIN AND WIRING STANDARD DEFINITION ...................................................................................12

www.avenview.com Page 1

1. IMPORTANT SAFEGUARDS

Please read all of these instructions carefully before you use the device. Save this manual for future reference.

What the warranty does not cover

•Any product, on which the serial number has been defaced, modified or removed.

•Damage, deterioration or malfunction resulting from:

•Accident, misuse, neglect, fire, water, lightning, or other acts of nature, unauthorized product modification, or failure to

follow instructions supplied with the product.

•Repair or attempted repair by anyone not authorized by us.

•Any damage of the product due to shipment.

•Removal or installation of the product.

•Causes external to the product, such as electric power fluctuation or failure.

•Use of supplies or parts not meeting our specifications.

•Normal wear and tear.

•Any other causes which does not relate to a product defect.

•Removal, installation, and set-up service charges.

1.1SAFETY INSTRUCTIONS

The Avenview FO-HDM-IP4K-SET, HDMI Extender has been tested for conformity to safety regulations and requirements, and has

been certified for international use. However, like all electronic equipment’s, the FO-HDM-IP4K-SET should be used with care.

Read the following safety instructions to protect yourself from possible injury and to minimize the risk of damage to the unit.

!Do not dismantle the housing or modify the module.

!Dismantling the housing or modifying the module may result in electrical shock or burn.

!Refer all servicing to qualified service personnel.

!Do not attempt to service this product yourself as opening or removing housing may expose you to dangerous voltage

or other hazards

!Keep the module away from liquids.

!Spillage into the housing may result in fire, electrical shock, or equipment damage. If an object or liquid falls or spills on

to the housing, unplug the module immediately.

!Have the module checked by a qualified service engineer before using it again.

!Do not use liquid or aerosol cleaners to clean this unit. Always unplug the power to the device before cleaning.

www.avenview.com Page 2

1.2REGULATORY NOTICES FEDERAL COMMUNICATIONS COMMISSION (FCC)

This equipment has been tested and found to comply with Part 15 of the FCC rules. These limits are designed to provide

reasonable protection against harmful interference in a residential installation.

Any changes or modifications made to this equipment may void the user’s authority to operate this equipment.

Warning symbols Description

ONLY USE THE PROVIDED POWER CABLE OR POWER

ADAPTER SUPPLIED. DO NOT TAMPER WITH THE

ELECTRICAL PARTS. THIS MAY RESULT IN ELECTRICAL

SHOCK OR BURN.

DO NOT TAMPER WITH THE UNIT. DOING SO WILL

VOID THE WARRANTY AND CONTINUED USE OF THE

PRODUCT.

THE VIDEO BOARDS ARE VERY SENSITIVE TO STATIC.

PLEASE ENSURE IF RACK MOUNTED OR INSTALLED ON A

SURFACE, IT SHOULD BE IN A GROUNDED ENVIROMENT.

lASER BEAM uSED IN OpTICAl COMMuNICATIONS ARE

INVISIBlE AND CAN SERIOuSly DAMAGE THE EyES.

VIEWING IT DIRECTly DOES NOT CAuSE ANy pAIN TO

THE EyE BuT SERIOuS DAMAGE CAN BE DONE TO THE

RETINA Of THE EyE

www.avenview.com Page 3

2. INTRODUCTION

FO-HDM-IP4K-SET, HDMI extender set is designed to provide high quality video signal transmission over fiber optic cable or an

existing fiber network. Avenview's FO-HDM-IP4K-SET delivers an amazing pixel to pixel transmission of 4K@30 or 1080p HDMI

signal up to 20 kilometers. With this extender users overcome the length restrictions of standard HDMI cables or UTP Extenders. This

unit can control your IR device from the monitors side with its supplied IR technology built in.

Bonus feature: The FiberTransmitter is also compatible with the HDM-C6IPX-R CAT5/6 Receiver, this simply means user can

migrate from a Fiber network to to copper network by adding the comptible RX device.

The Sender and Receiver units can extend 20000 meters (20 km) over a Fiber Optic cable point to point;

The Sender can be connected to a Fiber network switch to establish anIP address therefore sending 1080p/4K video signals to

multiple Receivers connected to the Fiber network switch and the HDMI displays;

Multiple Senders can be connected to a Managed Fiber switch with VLAN/IGMP support therefore sending 1080p/4K video

signals to Receivers connected to the network switch to show different sources on multiple displays;*

•Extends HDMI signal up to 20 km over fiber optic;

•HDCP compliant;

•Supported resolutions: 480i@60Hz,480p@60Hz,576i@50Hz,576p@50Hz,720p@50/60Hz,1080i@50/60Hz,1080p@50/60Hz

4K@25/30Hz

•Supports point to point transmission function which can be expanded to the multi-point to point transmission

function.

*Requires a managed Gigabit switch with VLAN/IGMP support to have a soultion with multiple sources (Transmitters). Standard

Gigabit switch can only support one transmitter.

- The managed switch must support port based IEEE 802.1Q VLAN, IGMP, and to allow duplicate IP addresses across the VLAN

domains.

- Each VLAN acts as independent HDMI over IP Channel on the network.

•Number of Senders and Receivers that can be used is dependent on bandwidth of the network switch.

•Single mode fiber optic transmission.

•

Built-in electromagnetic interference prevention in environment for long distance transmission.

Low signal loss, wide frequency band and strong anti-interference features;

High-end aluminum alloy enclosure design.

Wall-mountable design for convenient installation.

Support IR pass back for easy control.

FEATURES:

FIBER Network Switch with copper ports COPPER Network Switch with Fiber ports

www.avenview.com Page 4

2.1 PACKAGE CONTENTS

Before you start the installation of FO-HDM-IP4K, please check the package contents:

1HDMI IPX TRANSMITTER X 1

2HDMI IPX RECEIVER X 1

5POWER ADAPTER (5VDC2A) X 2

6USER’S MANUAL X1

2.2 BEFORE INSTALLATION

•Put the product in an even and stable location. If the product falls down or drops, it may cause an injury or malfunction.

•Don’t place the product in too high temperature (over 50°C), too low temperature (under 0°C) or high humidity.

•Use the DC power adapter with correct specifications. If inappropriate power supply is used then it may cause a fire.

3IR EXTENDER

4IR BLASTER

X 1

www.avenview.com Page 5

2.3 APPLICATION DIAGRAM

www.avenview.com Page 7

2.4PANEL DESCRIPTION & LAYOUT

This product is SDFNDJHGDVDVHW ZKLFKLQFOXGHV a Transmitter and a Receiver.

2.4.1 Front Panel (Transmitter, FO-HDM-IP4K-S)

2.DC 5V:Connect the 5 V DC power supply included.

1.POWER LED: LED lights red when device is

powered on

4.LINK LED: When connected to RX or network switch

the LED will light GREEN.

2.4.2 Rear Panel (Transmitter, FO-HDM-IP4K-S)

3.DATA LED: When data is transmitting from the

source the led will continuously flash YELLOW.

5.OPTICAL OUT: Connect SC single mode fiber optic cable.

2.IR OUT: Plug the IR Blaster cable for IR signal being transmitted.

place IR Blaster within direct site of the device being controlled.

1.HDMI IN: Connect to HDMI source via HDMI

Cable.

3.RESET: To reset the unit when no link is established.

Important Please do not connect the FO-HDM-IP4K to a POE network switch this will damage and the

units will be come non functional.

123 4

125

2.4.4Front Panel (Receiver, FO-HDM-IP4K-R)

2.4.5Rear Panel (Receiver, FO-HDM-IP4K-R)

www.avenview.com Page 8

123

123 4

2.IR IN: plug the IR Extender cable for IR signal being received.

place IR Extender within direct line of site with the IR Remote.

1.HDMI OUT: Connect to HDMI Display via

HDMI Cable.

3.RESET: To reset the unit when no link is established.

2.DC 5V:Connect the 5 V DC power supply included.

1.POWER LED: LED lights red when device is

powered on

4.LINK LED: When connected to RX or network switch

the LED will light GREEN.

3.DATA LED: When data is transmitting from the

source the led will continuously flash YELLOW.

5.OPTICAL IN: Connect SC single mode fiber

optic cable.

Inhaltsverzeichnis

Andere Avenview Extender Handbücher

Avenview

Avenview HDM3D-C53X-SET Bedienungsanleitung

Avenview

Avenview HDM-C5-3X-SET Bedienungsanleitung

Avenview

Avenview FO8K-DP MM Series Bedienungsanleitung

Avenview

Avenview DVI-C5-LC-R Bedienungsanleitung

Avenview

Avenview FO-DP-XX-MM Bedienungsanleitung

Avenview

Avenview DVI-C5-R Bedienungsanleitung

Avenview

Avenview HDM-C5SP-4 Bedienungsanleitung

Avenview

Avenview FO-DP4K-300-EMIX Bedienungsanleitung

Avenview

Avenview FO-HDSDI-SET Bedienungsanleitung

Avenview

Avenview HDMI-C5-3-SET Bedienungsanleitung

Avenview

Avenview HDM3D-C5SP-4 Bedienungsanleitung

Avenview

Avenview HDM3D-C53X-SET Bedienungsanleitung

Avenview

Avenview WL-VGA-EXT Bedienungsanleitung

Avenview

Avenview HDM3D-C53X-SET Bedienungsanleitung

Avenview

Avenview C5-USB-200 Bedienungsanleitung

Avenview

Avenview HDM-C6IP-SET Bedienungsanleitung

Avenview

Avenview HDMI-C5-4 Bedienungsanleitung

Avenview

Avenview HDM3D-C5IR-SET Bedienungsanleitung

Avenview

Avenview FO-VGA-DVI Bedienungsanleitung

Avenview

Avenview HBT-C6PLT-SET Bedienungsanleitung

Avenview

Avenview HDM-C6IP-SET Bedienungsanleitung

Avenview

Avenview HBT2-C6POH-USB-SET Bedienungsanleitung

Avenview

Avenview VTS-C5-R Bedienungsanleitung

Avenview

Avenview HDM3D-C5SP-8 Bedienungsanleitung

Beliebte Extender Handbücher anderer Marken

SY HDBT-60T Bedienungsanleitung

Appsys ProAudio

Appsys ProAudio ADX-16 Bedienungsanleitung

Atlona

Atlona RS232 Bedienungsanleitung

IDK

IDK OPF-TH1000-A Bedienungsanleitung

Enable-IT

Enable-IT 824WP Bedienungsanleitung

Worx

Worx Landroid RadioLink WA0864 Technisches Datenblatt

TP-Link

TP-Link TL-WA730RE Bedienungsanleitung

Camplex

Camplex CMX-HDMI-SFPL Bedienungsanleitung

SC&T

SC&T HE03-4K Bedienungsanleitung

Marmitek

Marmitek MegaView70 Bedienungsanleitung

Samsung

Samsung SCS-26UC4 Bedienungsanleitung

Foxun

Foxun SX-GES24 Bedienungsanleitung

MuxLab

MuxLab 500771 Bedienungsanleitung

foxunhd

foxunhd SX-AEX01 Bedienungsanleitung

TERK Technologies

TERK Technologies LFIRX2 Bedienungsanleitung

Devolo

Devolo Audio Extender Handbuch

Edimax

Edimax EW-7438RPn V2 Bedienungsanleitung

Shinybow USA

Shinybow USA SB-6335T5 Bedienungsanleitung