Avital Bandido 2 Bedienungsanleitung

Bandido2

Owner's Manual

Bandido2

Owner's Manual

Table of Contents

Bandido2..................................1

Lifetime Warranty............................1

Anti-Carjacking..............................1

Remote Controls .............................1

Electronic Scan Prevention (ESP).....................2

Instant Remote Control Code Deletion..................2

One-Step Remote Control Code Learning................2

Valet Switch...............................2

Operating Your Bandido

System.....................3

To Arm the Alarm System ........................3

To Disarm the Alarm System .......................3

Operation of the Anti-Carjacking Feature.................3

To Activate the Anti-Carjacking Feature..................4

To Deactivate the Anti-Carjacking Feature ................4

Remote-Controlled Silent Arm/Disarm ..................5

User-Programmable Long-Term Silent Arm/Disarm ............5

Interior Light Illumination ........................5

To Activate Optional Accessories.....................5

Zone

™ Impact Sensor .........................5

Protected Valet Mode ..........................6

Remote-Controlled Valet.........................6

User-Programmable Passive Door Lock .................7

User-Programmable Ignition-Controlled Door Lock/Unlock.......7

Remote Panic with Safety Locks™ ....................7

LED System Status Indicator .......................7

Previous Intrusion Alert .........................7

Specific Zone Intrusion Identification ..................8

Automatic Malfunction Override.....................8

Alarm State Memory ...........................8

User-Programmable Features.......................9

Programming Table for System Features.................10

Programming Table for Remote Controls................10

Bandido2

Congratulations! You have just purchased the Bandido2

, a full-featured vehicle

securitysystemwithanti-carjackingmanufacturedbyAvitalTechnologies,Inc.

To fully benefit from the capabilities of your system, we encourage you to

read the Owner’s Manual thoroughly before using the system. If you have any

problems or questions regarding your system, consult the dealer from whom

you purchased this product. To locate an authorized Avital dealer, contact

Avital Technologies directly at 1-800-253-0334 (toll-free within the U.S. only)

or 1-847-215-2233. In Mexico, dial 525-605-8541.

Lifetime Warranty

Avital guarantees the operation of your Bandido2

control unit and remote

controls for as long as you own your car. (Please refer to your Lifetime Limited

Warranty Card for complete information.) Make sure that you receive your

warranty card from your dealer, complete the required information and mail

the registration portion to Avital Technologies. You should retain the top

portion of the warranty card for your records.

Anti-Carjacking

The Anti-Carjacking feature of the alarm system is designed for personal

protection as well as the recovery of your carjacked vehicle. In the event of a

carjacking attempt, do not resist. If your vehicle is carjacked, the Bandido2

will

automatically activate the siren, flash the lights and immobilize the vehicle's

ignition and starter.

Carefully read the following pages for specific operating instructions.

Remote Controls

Included with your system are two AviGlo™3-button/6-channel remote

controls. Once exposed to light, the AviGlo remote control buttons will glow,

making the buttons visible in the dark.

The remote control (remote) is a miniature transmitter powered by a small +12

volt battery. Obstructions, electrical or radio interference, weather conditions,

window tint or a weak battery can reduce this range. Your remote is the key to

your system and can be used to arm and disarm your alarm, lock and unlock

your doors, and control optional accessories such as a remote engine starter,

window roll-up and garage door opener.

Bandido 2

Owner's Manual

The Bandido2

system can accept up to four Avital remote controls. Additional

remote controls and remote control batteries can be purchased from any

authorized Avital dealer, or by calling Avital Technologies at 1-800-253-0334

(toll-free within the U.S. only) or 1-847-215-2233. In Mexico, dial

525-605-8541.

Electronic Scan Prevention (ESP)

Your system also includes ESP, which blocks electronic scanner codes

preventing unauthorized operation of your system.

Instant Remote Control Code Deletion

In the event of a lost or stolen remote control, all remote controls can be

erased from the system’s memory preventing unauthorized system operation.

(See the "Programming Table for Remote Controls" on page 10.)

One-Step Remote Control Code Learning

The Bandido2

system allows you to add new remote controls in one step. (See

the "Programming Table for Remote Controls" on page 10.)

Valet Switch

The valet switch is a small hidden toggle switch which allows you to control all

of the system’s programmable features. (See "User-Programmable Features" on

page 9.) This switch can only be controlled with the use of your ignition key.

NOTE: Be sure to have your dealer show you where the valet switch is

located.

Bandido2

Owner's Manual

Operating Your Bandido2

System

To Arm the Alarm System

Your alarm system can be programmed for active or passive arming. Active

arming means the system can only be armed with the remote control. Passive

arming means the system will automatically arm itself. (See the "Programming

Table for system Features"on page 10.)

Active Arming:

Press remote button #1 for 1-2 seconds. The siren will chirp twice, the parking

lights will flash twice, the doors will lock, the LED will flash slowly and the

starter will be disabled. * If your system was installed with the door lock/unlock feature,

All other door lock/unlock related features will apply.

Passive Arming:

Turn the ignition key "OFF," exit the vehicle and close the doors. When the

interior lights turn off, the LED will begin flashing rapidly to indicate the alarm

is passive arming. After 30 seconds, the siren will chirp twice, the parking

lights will flash twice, the LED will flash slowly and the starter will be disabled

(at any time during passive arming, the alarm can be actively armed).

To Disarm the Alarm System

Press remote button #1 for 1-2 seconds. The siren will chirp once, the parking

lights will flash once, the doors will unlock, the interior lights will turn on, the

LED will turn off and the starter will be enabled.

Operation of the Anti-Carjacking Feature

There are two separate stages for anti-carjacking activation.

Alert Mode:

The Anti-Carjacking activation begins as soon as the ignition key is turned

"ON" or the engine is started. After 10 seconds, the siren will begin chirping to

alert you to deactivate the feature with your remote control. If the feature is

not deactivated, the siren will continue to chirp 7 times which takes

approximately 15 seconds. The parking lights will then begin to flash for 10

seconds. This will give you a total of 35 seconds to deavtivate the

anti-carjacking feature with your remote control.

Bandido2

Owner's Manual

Engine Shut Down Mode:

After the parking lights have flashed for 10 seconds, the siren will sound and

the parking lights will continue to flash. The system will monitor the engine

RPM's. When the carjacker stops or slows for a turn, the engine will

automatically shut off and not allow the vehicle to be restarted. This process

will allow the carjacker to drive a safe distance from you before shutting down

the engine, but typically close enough to make recovery easier.

When the system enters the Engine Shut Down Mode, the remote control

WILL NOT deactivate the Anti-Carjacking feature. The valet switch must be

used to deactivate the feature and start the engine.

To Activate the Anti-Carjacking Feature

The Anti-Carjacking feature can be programmed active or passive. Active

means the Anti-Carjacking feature can only be activated with the remote

control. Passive means the Anti-Carjacking feature will automatically activate

itself. (See the "Programming Table for System Features" on page 10.)

Active:

In a carjacking situation, while the engine is running, press the remote control

buttons #2 and #3 for 1-2 seconds. The system will automatically begin the

Alert and Engine Shut Down modes. The system does not provide any audible

or visual arming confirmation that would alert the carjacker.

Passive:

Every time the doors are opened and the engine is started or already running,

the Anti-Carjacking feature will automatically activate.

To Deactivate the Anti-Carjacking Feature

1.Start the engine.

2. Within 10 seconds, press the remote buttons #2 and #3 simultaneously for

1-2 seconds.

3. The parking lights will flash two times.

4.The LED will flash 4 times to confirm disarm.

5.While the engine is running, if a door is opened or the interior lights are

turned "ON," you must press the remote buttons #2 and #3 simultaneously

for 1-2 seconds to deactivate the Anti-Carjacking feature.

Bandido2

Owner's Manual

Remote-Controlled Silent Arm/Disarm

Press the remote button #3 for 1-2 seconds to armor disarmyour system

without the usual siren chirps.

Silent Arm Indications:

The parking lights will flash twice, the doors will lock, the starter will be

disabled and the LED will flash slowly.

Silent Disarm Indications:

The parking lights will flash once, the doors will unlock, the starter will be

enabled and the LED will turn off.

User-Programmable Long-Term Silent Arm/Disarm

This feature allows you to completely disable the arm/disarm siren chirps until

you decide to restore them. (See the "Programming Table for System Features"

on page 10.)

Interior Light Illumination

When the alarm system is remotely disarmed, the vehicle’s interior light(s) will

turn on for 30 seconds or until the ignition key is turned on.

To Activate Optional Accessories

Press remote button #2 for 1-2 seconds to activate an optional accessory. To

activate an additional optional accessory, press remote buttons #1 & #2

simultaneously for 1-2 seconds.

Zone2

™ Impact Sensor

The Zone2

Impact Sensor has two individual vibration/impact sensing zones.

Zone #1:

If a less threatening vibration or impact is detected, the siren will issue 2

warn-away chirps. A second violation will also issue 2 warn-away chirps. If

within 45 seconds a third violation is detected, the sensor will automatically

trigger the alarm. The siren will sound and the lights will flash.

Zone #2:

If a more threatening vibration or impact is detected at any time, the siren and

lights will activate instantly.

Bandido 2

Owner's Manual

Protected Valet Mode

You can place your system in Protected Valet Mode when your car is being

serviced by mechanics, car wash personnel or driven by valet attendants, and

still maintain possession of your remote control(s). While in Protected Valet

Mode, all alarm functions are bypassed to prevent undesired or accidental

arming. Remote-controlled lock/unlock and all optional accessories will still

operate.

To Turn on Protected Valet Mode:

1.Turn your ignition key to the "ON" position or start the vehicle.

2.Flick the valet switch to the "ON" position.

3. The LED will turn on solid red to indicate the system is in Protected Valet

Mode.

4.Turn your ignition key to the "OFF" position.

To turn off Protected Valet Mode:

1.Turn your ignition key to the "ON" position or start the vehicle.

2.Flick the valet switch to the "OFF" position.

3. The LED will turn off to indicate the system is no longer in Protected Valet

Mode.

4.Turn your ignition key to the "OFF" position.

Remote-Controlled Valet

For your convenience, the system can be put into Valet Mode via the remote

control. While in Remote-Controlled Valet, all alarm functions are bypassed.

Remote-controlled lock/unlock and all optional accessories will still operate.

NOTE: The system must be disarmed and the Anti-Carjacking feature

deactivated in order to activate the Remote-Controlled Valet feature.

To Activate Remote-Controlled Valet:

1.Press remote control buttons #1 and #3 at the same time for 1-2 seconds.

2. The parking lights will flash 4 times, and the LED will turn on solid red.

To Deactivate Remote-Controlled Valet:

1.Press remote control buttons #1 and #3 at the same time for 1-2 seconds.

2. The parking lights will flash 3 times and the LED will turn off.

Bandido2

Owner's Manual

User-Programmable Passive Door Lock

The system will not automatically lock the doors when the alarm passively

arms to prevent the keys and remote from accidentally being locked in the

vehicle. If you prefer, you can easily program the system to automatically lock

the doors every time the alarm passively arms. (See the "Programming Table

for System Features" on page 10.)

User-Programmable Ignition-Controlled Door Lock/Unlock

For the ultimate in security and convenience, the system will automatically

lock the doors when the ignition key is turned “ON” or when the vehicle

engine is started and the doors will unlock when the ignition key is turned

“OFF.” This feature can be programmed on or off. (See the “Programming

Table for System Features” on page 10.)

Remote Panic with Safety Locks™

In a threatening situation, you can activate Remote Panic with Safety Locks.

When activated, the siren will sound continually and the parking lights will

flash on and off. If the ignition key is "OFF," the doors will unlock. If the

ignition key is "ON," the doors will lock. To deactivate, press button #1 for 1-2

seconds.

LED System Status Indicator

The LED on your vehicle’s dashboard or center console will inform you of the

system status.

LEDStatus

OffSystem is disarmed

On solidIn Protected or Remote-Controlled Valet Mode

Slow flashSystem is armed

Flashing in cycles See "Specific Zone Intrusion Identification" on page 8

Rapid flashPassive Arming

Previous Intrusion Alert

If the vehicle had been tampered with and the alarm has been triggered, the

siren will chirp 3 times upon remote disarm instead of the usual 1 chirp.

Bandido

Owner's Manual

Specific Zone Intrusion Identification

If the alarm had been triggered in your absence, the siren will chirp 3 times

upon remote disarm (Previous Intrusion Alert). When you enter the vehicle

and turn the ignition “ON,” the LED will flash in cycles to specifically identify

which zone triggered the system.

LEDZone

One Flash...One Flash...Impact sensor

Two Flash...Two Flash...Hood/Trunk trigger

Three Flash...Three Flash...Door trigger

Automatic Malfunction Override

In the event of a faulty sensor or alarm input trigger zone, the alarm, when

remotely armed, will alert you by a series of chirps and parking light flashes.

How to Interpret the Chirps and Parking Light Flashes:

When you press the remote control buttons, the system will respond with

chirps and flashes of the parking lights to indicate the system status. An

explanation of these chirp/flash acknowledgments follows:

Number of chirps and flashes Explanation

1 chirp, 1 flash Disarming of the system

2 chirps, 2 flashesArming of the system

2 chirps and flashes, then 4 more chirps

and flashesArmed and there is a sensor malfunction

(automatically bypassed)

3 chirps, 3 flashes Disarmed and there was an intrusion attempt

4 chirps, 4 flashes Armed and there is a trigger malfunction

(automatically bypassed)

Alarm State Memory

If your vehicle’s battery is disconnected and later reconnected, the system will

automatically return to its last state prior to disconnection, whether it was

armed, disarmed or in Protected Valet Mode. For example, if a mechanic

disconnects the battery while the alarm is disarmed or in Protected Valet

Mode, he won’t trigger the system when he reconnects the battery. If a thief

interrupts power while the system is armed, and reconnects it, the alarm will

instantly sound, the parking lights will flash and the starter will be disabled.

Bandido 2

Owner's Manual

Inhaltsverzeichnis

Andere Avital Autoalarmanlage Handbücher

Avital

Avital Tornado Bedienungsanleitung

Avital

Avital 3300L Bedienungsanleitung

Avital

Avital Avistart 4001 Bedienungsanleitung

Avital

Avital 4118L Bedienungsanleitung

Avital

Avital 3300L Bedienungsanleitung

Avital

Avital Hurricane Bedienungsanleitung

Avital

Avital Paging Adaptor 5810 Bedienungsanleitung

Avital

Avital MAXX2 Bedienungsanleitung

Avital

Avital Phoenix 2 Bedienungsanleitung

Avital

Avital AviStart 3200 Bedienungsanleitung

Avital

Avital AviStart 3100 Bedienungsanleitung

Avital

Avital MAXX3 Bedienungsanleitung

Avital

Avital Tornado Bedienungsanleitung

Avital

Avital AVISTART 6501 Bedienungsanleitung

Avital

Avital Phoenix 2 Bedienungsanleitung

Avital

Avital Diablo 2 Bedienungsanleitung

Avital

Avital 4103 Bedienungsanleitung

Avital

Avital AviStart 6500 Bedienungsanleitung

Avital

Avital AviStart 6001 Bedienungsanleitung

Avital

Avital 5103 Bedienungsanleitung

Avital

Avital Point 3 Immobilizer Bedienungsanleitung

Avital

Avital G5103 Bedienungsanleitung

Avital

Avital AviStart 6000 Bedienungsanleitung

Avital

Avital 2000 Bedienungsanleitung

Beliebte Autoalarmanlage Handbücher anderer Marken

Clifford

Clifford 3606X Bedienungsanleitung

Ultra Start

Ultra Start 2500M SERIES Bedienungsanleitung

Ultra Start

Ultra Start 650 Series Bedienungsanleitung

Audiovox

Audiovox Prestige Platinum+ APS-511C Bedienungsanleitung

Sparkrite

Sparkrite SRA8 Bedienungsanleitung

Viper

Viper 4708V Bedienungsanleitung

Federal Signal Corporation

Federal Signal Corporation Pathfinder Siren Series Handbuch

Falcon

Falcon Predator XL3 Benutzerhandbuch

Audiovox

Audiovox Auto Security XR91 Betriebsanleitung

Clifford

Clifford Sabre II Bedienungsanleitung

CrimeStopper

CrimeStopper CS-8717 Kurzanleitung

Scytek electronic

Scytek electronic Vectra X3 Bedienungsanleitung

Clifford

Clifford CYBER 2 Bedienungsanleitung

Gemini

Gemini 7057 Bedienungsanleitung

FlashLogic

FlashLogic FLRSBA PRESTIGE Bedienungsanleitung

Magicar

Magicar FAI-440 Bedienungsanleitung

Clifford

Clifford Nova 3 Bedienungsanleitung

Viper

Viper 560XV Bedienungsanleitung