Balluff BIS M-411-068-001-09-S72 Bedienungsanleitung

Select a suitable location to mount the RFID

Controller. The Unit may be mounted to wood,

plastic fixtures and metal plate surfaces. However,

do not recess the controller in metal. For optimal

performance, allow 60mm (2.5inches) clearance

from metallic objects around the sides of the

controller.

To secure the controller to the mounting surface,

use two M5 (#10) diameter screws and two

washers. The Unit may be mounted horizontally

or vertically, but should be aligned in such a

manner that the LED indicators can be seen during

operation.

1. Fasten the Unit to the mounting surface

using two screws (place one washer on

each screw before insertion). Tighten

screws to between 1.3 and 1.7Nm (12-15lbs per inch).

2. Download the USB driver software bundle from the Balluff website (www.balluff.com).

Extract the .zip ﬁle archive to a separate folder on the desktop of the host computer.

3. Attach the 5-pin, reverse keyed female M12 interface connector from a suitable USB

interface cable (CBL-1525) to the 5-pin, reverse keyed male M12 connector on the Unit.

4. Plug the remaining end of the USB interface cable into a USB port on the host computer.

The LEDs on the controller will ﬂash. The amber colored LED 22will remain lit to indicate

that the controller is in USB mode (see Figure 3). At this point, Windows™ will detect the

new hardware device and request the location of the USB driver ﬁles.

5. Browse to the folder containing the USB driver ﬁles. Refer to the “USB Driver Installation

Instructions”, included with the USB driver download, to complete the installation of the

USB driver.

6. To verify operations, download the serial version of the HF Dashboard Utility. The HF

Dashboard Utility allows users to conﬁgure and control their controllers and send RFID

commands for testing purposes.

This document provides instructions and information designed to assist users in the hardware

setup and conﬁguration of the RFID Controller.

Installing the RFID Controller

C1007-Series

RFID Controller

BIS M-411-068-001-09-S72

(C1007-USB-01)

Installation Guide

ESCORT M EMORY SYSTEMS

Model:

S/NMADE IN USA



116.4

[4.58]

12.5

[0.49]

Controller Dimensions

105.8

[4.16]

8.8

[0.34]

8.8

[0.34]

15.9

[0.63]

TOP

VIEW

FRONT

VIEW

LEFT

VIEW

Figure 1: Controller Dimensions

75.2

[2.96]

[0.75]

[0.94] 12.5

[0.49]

20.6

[0.81]

Millimeters

[Inches]

No. 890411 E .Edition 1210; Subject to modification.

Installation Guidelines

• Do not recess the BIS M-411 in metal and allow 60mm (2.5inches) clearance from metallic

objects around the sides of the BIS M-411.

• Avoid mounting the RFID controller near sources of EMI (electro-magnetic interference) or near

devices that generate high ESD (electro-static discharge) levels.

• If electrical interference is encountered (as indicated by a significant reduction in read/write

performance), relocate the controller to an area free from potential sources of interference.

• Route cables away from motors, solenoids, unshielded cables and any wiring that carries high

voltage or high current.

• When installing multiple RFID controllers that operate at the same frequency (13.56 MHz), maintain

a minimum distance of 20cm (8inches) between adjacent RF devices.

The controller obtains power directly from the USB bus and requires 500mA.

Power Requirements

Interface Connector - Pinout

The

controller

has one

5-pin,

male M12

interface

connector.

Figure 2: Interface Connector - Pinout

PIN 5:

SHIELD

PIN 4:

GND

PIN 2:

D-

PIN 3:

D+

PIN 1:

+5V

5-Pin, Reverse

Keyed Male M12

Interface

Connector

For complete operating instructions for the RFID Controller refer to the:

BIS M-411-Series RFID Controllers - Operator’s Manual

Also available online are HF Dashboard™ and C-MacroBuilder™ software utilities.

The HF Dashboard is a Windows-based application that provides users with the ability to control,

conﬁgure and test their RFID hardware.

C-MacroBuilder is an easy to use GUI-driven utility for Windows. This software utility allows users

to build their own macro programs (which are stored internally on and executed directly by RFID

Controllers).

When C-MacroBuilder is used in conjunction with the HF Dashboard Utility, users have the ability

to design, save and execute custom macros from any supported RFID controller without the

need of a host computer to issue routine commands.

Final Notes

LEDs

Figure 4: LEDs

RF COM 2423222120PWR

COM USB MODE

ENABLED

POWER

ANTENNA FIELD

HF RFID Controllers

*-USB Models - LED Defaults

Dieses Handbuch passt für folgende Modelle

Andere Balluff Zubehör Handbücher

Balluff

Balluff BML-S1G0 7 M5E 0 Series Bedienungsanleitung

Balluff

Balluff IO-Link BES M12EH1-L01C40B-S04G-L04 Kurzanleitung

Balluff

Balluff BTL7-V50D-M C003 Series Bedienungsanleitung

Balluff

Balluff BTL7-A50 Series Bedienungsanleitung

Balluff

Balluff BES M30EH2-GNX15F-BT02-X03 Bedienungsanleitung

Balluff

Balluff BMD 1H Series Bedienungsanleitung

Balluff

Balluff BES M18MF2-PSC50B-BV02-EXE Bedienungsanleitung

Balluff

Balluff BOS R080K-UIM-RE10 Series Bedienungsanleitung

Balluff

Balluff BMF 203K-H Series Bedienungsanleitung

Balluff

Balluff IO-Link BES M12MG1-YIC60B-S04G Bedienungsanleitung

Balluff

Balluff BES M18MH2-GNX80F-S04G-EXC Bedienungsanleitung

Balluff

Balluff BUS M12E0-PPXCR-020-S04G Gebrauchsanweisung

Balluff

Balluff BOS 73 K Series Bedienungsanleitung

Balluff

Balluff BES M12MF2-PSC40F-BV02-EXE Bedienungsanleitung

Balluff

Balluff BTL304K Bedienungsanleitung

Balluff

Balluff BOS 21M-S4 Series Bedienungsanleitung

Balluff

Balluff BTL5-T1 M P-S103 Series Bedienungsanleitung

Balluff

Balluff BTL6-P111-M0950-A1-S115 Bedienungsanleitung

Balluff

Balluff BES M12MG2-GNX20B-BT02-EXB Bedienungsanleitung

Balluff

Balluff BSI R11A0-XB-CX S75G Series Bedienungsanleitung

Balluff

Balluff BTL7 ZA10 Series Bedienungsanleitung

Balluff

Balluff BBES M18MF2-PSC80F-BV02-EXD Bedienungsanleitung

Balluff

Balluff BES M30MH2-GNX10B-BT02-EXA Bedienungsanleitung

Balluff

Balluff BES M18MH2-GNX80F-BT02-EXB Bedienungsanleitung

Beliebte Zubehör Handbücher anderer Marken

Hillco

Hillco 2810 Bedienungsanleitung

Siemens

Siemens QSA2700D Bedienerhandbuch

Contours

Contours ZY024 Bedienungsanleitung

Saivod

Saivod VS621 Bedienungsanleitung

SCE

SCE ENVIRO-THERM SCE-TE170B24VSS Bedienungsanleitung

Z-Wave

Z-Wave HSD-200Z Bedienungsanleitung

turck

turck FMX-IM-2UPLI63FX Bedienungsanleitung

Decagon Devices

Decagon Devices 10HS Bedienungsanleitung

UPPAbaby

UPPAbaby Cup Holder Bedienungsanleitung

Elko

Elko SmartSensor Leakage Wireless Bedienungsanleitung

Grizzly

Grizzly H8371 Bedienungsanleitung

Panasonic

Panasonic HG-T Series Bedienungsanleitung

IFM Electronic

IFM Electronic Efector 250 Series Referenzhandbuch

Virtuox

Virtuox VirtuCLEAN 2.0 Bedienungsanleitung

DigiDesign

DigiDesign 888/24 I/O Bedienungsanleitung

PROZIS

PROZIS QUAY Bedienungsanleitung

patagonia

patagonia PSI Vest Bedienungsanleitung

SFC Energy

SFC Energy EFOY GO! Bedienungsanleitung