Blue Ox BX3781 Bedienungsanleitung

2009-13 Toyota Corolla

Installation Instructions

BX3781

405-0009 Rev. C Page 1 of 7 3/1/12

1. Blue Ox®towing products and accessories

are intended to be installed by Blue Ox®

Dealers who are familiar with our products and

have the equipment and knowledge to do “t

work.” When necessary, Blue Ox®Dealers can

be found at www.blueox.com or by contacting

our Customer Care Department at

(800)228-9289.

2. Many Blue Ox®Baseplates are designed to

use existing holes and hardware to mount

the baseplate to the towed vehicle. Even

though bolts are there, do not assume they

are adequate for baseplate mounting. Always

use hardware supplied in the hardware kit

or existing hardware specied in the

Baseplate Towing Installation Instructions.

Serial Number

Conrm the towability and pre-towing

procedures for your vehicle with

the owner’s manual or contact the

vehicle’s manufacturer for specic

towing procedures.

Please read BOTH these Installation Instructions and the General Towing Instructions

before attempting to install or operate this equipment.

Failure to read and follow these instructions

could result in separation of the towed vehicle

from the tow bar, causing property damage,

loss of towed vehicle, personal injury or death.

WARNING

Attachment Tab Height: 15”

Attachment Tab Width: 18 1/4”

Bolt Torque Specications

Torque in Foot-Pounds per Inch Bolts

Bolt Torque Specications

Torque in Foot-Pounds per Metric Bolts

Bolt Size Grade 8.8 Grade 10.9

6MM 6 8

8MM 16 22

10MM 31 40

12MM 54 70

14MM 89 117

Bolt Size Grade 5 Grade 8

1/4” 10 14

5/16” 19 29

3/8” 33 47

7/16” 54 78

1/2” 78 119

5/8” 154 230

2009-13 Toyota Corolla

Installation Instructions

BX3781

405-0009 Rev. C Page 2 of 7 3/1/12

31 4

NIP4 ROTCENNOC

YAWAKAERB HCTIWS

NIP6 ROTCENNOC

1873XB .ONMETIREBMUNTRAP

18025-16

N,DLW

20556-16

'MDLW

39643-26

ATTTA

42285-101

TPADA

54027-201

KAERB

60500-102

02-4/1

72910-102

23-01#

88630-102

61-8/3

93550-102

02-4/1

017400-202 23-01#

112010-202

02-4/1

210100-302OL"8/3

314500-302

OL01#

9331-392

CTIWS

5080-492

NNOC

2090-492

NNOC

Important:

Use only genuine factory replacement parts on your baseplate. Do NOT substitute homemade or non-typical parts. If a bolt is lost or

in need of replacement, for your safety and the preservation of your baseplate, be sure to use a replacement bolt of the same grade

(In most cases it will be Grade 5, please reference the parts list above). Replacement parts may be ordered through your nearest Blue

Ox® Dealer or Distributor.

Tools Required

10MM Socket Large Vise Grip

14MM Socket Flat Screw Driver

9/16” Socket Phillips Screw Driver

1 1/4” Hole Saw Utility Knife

13/32” Drill Bit Loctite Red

Parts List

Ref. No. Qty. Part # Description

1 6 61-5208 3/8”-16 Nut Plate with 14” Wire

2 1 61-6550 BX3781 Baseplate

3 2 62-3469 Attachment Tab

4 2 101-5822 4 Way Connector Adapter

5 1 102-7204 Breakaway Bracket

6 2 201-0050 1/4”-20 x 3/4” Hex Head Bolt, Grade 5, ZP

7 2 201-0192 #10-32 x 1/2” Round Slotted Head Screw

8 6 201-0368 3/8”-16 x 1-1/4” Hex Head Bolt, Grade 5, ZP

9 2 201-0553 1/4”-20 x 1/2” Hex Wshd Type F TCS Screw, ZP

10 2 202-0047 #10-32 Hex Nut

11 2 202-0102 1/4”-20 Hex Nylon Nut, ZP

12 6 203-0010 3/8” Lock Washer, ZP

13 2 203-0054 #10 Lock Washer

14 2 226-0046 (not shown) 36” Class III Safety Cables

15 2 229-0359 (not shown) 3/8” Quicklink, ZP

16 1 290-0437 (not shown) Black Receiver Cap Plug

17 1 293-1339 (not provided) Breakaway Switch

18 1 294-0805 (not provided) 4 Pin Connector

19 1 294-0902 (not provided) 6 Pin Connector

2009-13 Toyota Corolla

Installation Instructions

BX3781

405-0009 Rev. C Page 3 of 7 3/1/12

Vehicle Weight:

Motorhome mount tow bars are recommended for

use with this baseplate. Due to the design of the

removable tabs, the RangeFinderII, Adventurer, and

Ambassador tow bars can not be used. TheAcclaim

tow bar may be used, but will not fold and store on the

front of the vehicle. Adapters, except the BX8833 and

BX88151, can not be used with this baseplate.

Tow Bar Adapters are NOT to be used with

vehicles weighing over 5,000 lbs.

Installation Notes: The fascia and

aluminum bumper and are removed and

reinstalled during installation of the baseplate.

Drilling is required. Trimming of the fascia is

required.

The dimensional variations between otherwise

identical vehicles can be considerable. While

the baseplate was designed for easy installation,

it may be necessary to tailor the baseplate

slightly to compensate for auto manufacturer’s

tolerances. These minor adjustments may include

ling a hole slightly, bending electrical rods and/

or bending end plates.

The BX8848 Bulb and Socket Wiring Kit is

recommended for this vehicle.

Installation Instructions:

1. Using the Phillips screw driver, remove the

Phillips screws (white arrow) from the top

corner edge of the fascia. Remove push pin

(gray arrow), do this to both sides and set

aside for later reinstallation.

2. Remove push pin from top edge of fascia

just below hood latch and set aside for

reinstallation later.



2009-13 Toyota Corolla

Installation Instructions

BX3781

405-0009 Rev. C Page 4 of 7 3/1/12

5. Behind the fascia on the bottom of the bumper,

are two push pins to remove from the fascia’s

tabs. Remove with a at screw driver. Pull the

fascia forward on both sides and set aside for

later reinstallation.

7. Using a 14MM socket, remove the two bolts

on each side of the bumper and take the

bumper off. Set aside for later reinstallation.



6. Remove the styrofoam. On the driver’s side

only, using a at screw driver release the tabs

from the top of the bumper and tie the wire

loom up in the open area during baseplate

installation.



4. Just forward of the front tire underneath, using

a 10MM socket, remove the two metric bolts

(white arrows). Using a at screw driver,

remove the push pin (gray arrow). Do this on

both sides and set aside for later reinstallation.



3. Just forward the front tire on the upper corner

of the fascia and inside the wheel well, turn the

screw 90oto remove it (white arrow). Using a

at screw driver, remove the upper push pin

(gray arrow). Do this on both sides and set

aside for later reinstallation.



2009-13 Toyota Corolla

Installation Instructions

BX3781

405-0009 Rev. C Page 5 of 7 3/1/12

8. Remove the black shield on both sides. It will

not be reinstalled.



11. Slide the baseplate up between the frame

rails, align with the existing hole on each side

and clamp.



10. Move the bracket out of the way by sliding it up. Measure 7” up. Reroute the wire up and reattach

the bracket so that the bottom of it is 7” up.



9. On the driver’s side pull the wiring out of the

existing hole. Drill a hole in the frame rail

under but connected with the existing hole

using the 1 1/4” hole saw on both sides. This

hole will allow the installer to insert the nut

plates inside of the frame rail.

10A 10B 10C



2009-13 Toyota Corolla

Installation Instructions

BX3781

405-0009 Rev. C Page 6 of 7 3/1/12

15.Attach baseplate safety cables as in above

photos or as close to as possible. If you are

unable to place safety cables in this location,

position the cables around a solid piece of the

frame. Do this on both sides.

BE SURE TO USE LOCTITE®RED ON ALL BOLTS

BEFORE TIGHTENING. TIGHTEN ALL BOLTS

ACCORDING TO THE TORQUE CHART ON THE

FRONT PAGE OF THESE INSTRUCTIONS OR ON

PAGE 3 OF THE BASEPLATE TOWING GENERAL

INSTRUCTIONS.



12. Insert 3/8-16 x 1 1/4” hex bolts with 3/8” lock

washers attached to 3/8-16 nut plates with

inserted into the frame rail on both sides to

hold the baseplate in place.

13. Using the baseplate as a template, drill both

holes in the under side of the frame rail with a

13/32” drill bit. Do this on both sides.



14. Insert 3/8-16 x 1 1/4” hex bolts and 3/8” lock

washers with 3/8-16 nut plates with inserted

into the frame rail. Use loctite on all the

bolts and tighten. Do this on both sides and

the bolts inserted previously. Reinstall the

bumper.



Install the tow bar and safety cables

according to the instructions provided in their

packages. When demonstrating this to the

customer, be sure to include all the contents

and packages.

Do NOT substitute other devices if the tow

bar pins and clips are misplaced.

2009-13 Toyota Corolla

Installation Instructions

BX3781

405-0009 Rev. C Page 7 of 7 3/1/12

Be sure that ALL electrical connections

are plugged in properly and functioning

BEFORE installing the fascia.

DEALER or INSTALLER:

Be certain the user receives the

instruction sheets for their products.

One Mill Road, Industrial Park

Pender, Nebraska 68047

Phone: (402) 385-3051 • Fax: (402) 385-3360

www.blueox.com

CUSTOMER SERVICE COMMITMENT

Blue Ox is committed to providing you with

exceptional customer care throughout your lifetime

with our products. Our team is here to assist you

with any questions you may have regarding the

performance of your product. Simply call 1-800-228-

9289 and you can speak with our customer care team.

Additionally, please visit our website to see which

rallies our Destination America team will be attending.

For a nominal fee, our service technician will service

your towing system to ensure it’s in proper working

condition. Also as a commitment to our customers,

should you visit our factory you can stay at our full

service Blue Ox campground at no charge along with

enjoying a factory tour.

Again thank you for being our customer and for the

condence you have shown in the performance of our

products. It is because of customers like you we enjoy

the success we have today.

Shown With Removable Tabs

16. Hold the fascia as close to its original position

as possible, mark and trim the grill with a utility

knife to allow the baseplate receivers to come

through. Reinstall the fascia.

NOTE: On 2009-10 models see Figure A. For

2011 models reference Figure B.



Figure A

Figure B

Inhaltsverzeichnis

Andere Blue Ox Autozubehör Handbücher

Blue Ox

Blue Ox SwayPro BXW0551 Bedienungsanleitung

Blue Ox

Blue Ox BedSaver BXR4401 Bedienungsanleitung

Blue Ox

Blue Ox BX2610 Bedienungsanleitung

Blue Ox

Blue Ox BedSaver BXR4502 Bedienungsanleitung

Blue Ox

Blue Ox SwayPro BXW0553 Bedienungsanleitung

Blue Ox

Blue Ox BX2800 Bedienungsanleitung

Blue Ox

Blue Ox BX1678 Bedienungsanleitung

Blue Ox

Blue Ox BX1120 Bedienungsanleitung

Blue Ox

Blue Ox BX1958 Bedienungsanleitung

Blue Ox

Blue Ox BedSaver BXR4102 Bedienungsanleitung

Blue Ox

Blue Ox SportCarrier II Technisches Datenblatt

Blue Ox

Blue Ox BX1141 Bedienungsanleitung

Blue Ox

Blue Ox BX4102 Bedienungsanleitung

Blue Ox

Blue Ox BX1126 Bedienungsanleitung

Blue Ox

Blue Ox BX7365 Bedienungsanleitung

Blue Ox

Blue Ox BX8847 Bedienungsanleitung

Blue Ox

Blue Ox BX1120 Bedienungsanleitung

Blue Ox

Blue Ox BX3216 Bedienungsanleitung

Blue Ox

Blue Ox TRION BX7520P Bedienungsanleitung

Blue Ox

Blue Ox BX88420 Bedienungsanleitung

Blue Ox

Blue Ox BX2323 Bedienungsanleitung

Blue Ox

Blue Ox ADVENTURER BX7322 Bedienungsanleitung

Blue Ox

Blue Ox DH2303 Bedienungsanleitung

Blue Ox

Blue Ox BX1117 Bedienungsanleitung

Beliebte Autozubehör Handbücher anderer Marken

James Baroud

James Baroud Odyssey Bedienungsanleitung

Motorola

Motorola i50sx Bedienungsanleitung

Yakima

Yakima 9MM STANDARD BIKE MOUNT Bedienungsanleitung

Feniex

Feniex T3 Bedienungsanleitung

Kia

Kia E8300-4D000 Bedienungsanleitung

Brink

Brink 756843 Bedienungsanleitung

Whispbar

Whispbar K085W Bedienungsanleitung

v.link

v.link CI-VL2-PC-HSD Bedienungsanleitung

Viking

Viking Stack-Rack Kurzanleitung zur Einrichtung

Aries

Aries 203015 Bedienungsanleitung

Choetech

Choetech AT0005 Bedienungsanleitung

ZZ2

ZZ2 ZZAIR-PRO Bedienungsanleitung

Holman

Holman 4A80L Bedienungsanleitung

Thule

Thule 2075 Bedienungsanleitung

Motorola

Motorola T325 Bedienungsanleitung

TAUBENREUTHER

TAUBENREUTHER 16-3950 Installationsanleitung

DV8

DV8 FBJL-02 Bedienungsanleitung

Prorack

Prorack K1163 Bedienungsanleitung