Bradley SS-2/IR/JUV Bedienungsanleitung

IMPORTANT

Read this entire installation manual

to ensure proper installation, then

file these instructions with the

owner or maintenance department.

Flush all the water supply lines

before making connections.

Wall anchors used must have a

minimum pull-out rating of 1,000

lbs.

Product warranties may be found

under "Product Information" on our

web site at www.bradleycorp.com.

SS-2/IR/STD

SS-2/IR/JUV

Express® Lavatory

System SS-Series

(Standard* and Juvenile Height)

*Express® Lavatory Systems

are ADA compliant.

Table of Contents

Pre-Installation Information . . . . . . . . . . . . . . . .2

Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . .3-4

Installation Instructions . . . . . . . . . . . . . . . . 5-11

Cleaning and Maintenance Instructions . . . . . .12

Soap Dispenser Maintenance . . . . . . . . . . .13-14

Wiring Diagram . . . . . . . . . . . . . . . . . . . . . . . .14

Assembly of Components . . . . . . . . . . . . . .15-16

Check Valve Troubleshooting . . . . . . . . . . . . . .17

Solenoid Valve Troubleshooting . . . . . . . . .17-18

Vernatherm™ Valve Maintenance & Service . .19

P.O. Box 309, Menomonee Falls, WI 53052-0309

TEL. 1-800-BRADLEY FAX 262-251-5817

http://www.bradleycorp.com

Installation

Instructions

OBSOLETE

215-1243 Rev. E; EN 08-805

Page 1 of 19 4/24/08

Express® Lavatory System SS-Series

SS-2/IR/STD, SS-2/IR/JUV Installation - Obsolete

4/24/08 Bradley Corporation • 215-1243 Rev. E; EN 08-805

Pre-Installation Information

Barrier-free and ADA compliant - standard height mounting

The SS-2/IR/STD Express® Lavatory System must have a rim height of 34" above finished

floor to be compliant with Americans with Disabilities Act (ADA). When mounted at 34" rim

height, the Express® meets ADA, ANSI and UFAS requirements for barrier-free clearances,

reaches and controls. Always check local codes and ordinances for compliance.

Barrier-free and ADA compliant - juvenile height mounting

The SS-2/IR/JUV Express® Lavatory System is compliant with Americans with Disabilities Act

(ADA) Accessibility Guidelines for Buildings and Facilities: Building Elements Designed for

Children's Use; Final Rule.

Infrared sensor and solenoid

Each sprayhead is controlled by a separate sensor and solenoid valve, enabling each user to activate

a single flow of water. Each valve uses less than half the maximum of hot water allowed by the

ANSI/ASHRAE/IES 90A-1980 Standard.

Supplies required for installation:

• (6) 3/8" wall anchors, bolts and washers to mount frame and bowl to wall

(minimum pull-out rating of 1,000 lbs.)

• 1/2" NPT hot and cold supply piping

• 1-1/2" NPT drain piping

• 110 volt electrical outlet for 110/24 VAC plug-in transformer

(supplied)

Express® Lavatory System SS-Series

Installation - Obsolete SS-2/IR/STD, SS-2/IR/JUV

Bradley Corporation • 215-1243 Rev. E; EN 08-805 4/24/08

(203)

22" (559)

34" (864

(152)

50"

(1270)

8-1/2"

(216)

21"

(533)

10" (254)

Radius

8" (203)

Radius 30"

(762)

38-1/4"

(971)

SS-2/IR/STD Express® Lavatory System Dimensions

Standard Height Mounting

Express® Lavatory System SS-Series

SS-2/IR/STD, SS-2/IR/JUV Installation - Obsolete

4/24/08 Bradley Corporation • 215-1243 Rev. E; EN 08-805

38"

(965) 34"

(864) 29"

(737)

11"

(279)

(229) 6"

(152)

(102)

30"

(762) 25"

(635)

11"

(279)

(229) 6"

(152)

(102)

34"

(864)

Standard Height

SS-2/IR/STD

Juvenile Height

SS-2/IR/JUV

Express® Lavatory System SS-Series

Installation - Obsolete SS-2/IR/STD, SS-2/IR/JUV

Bradley Corporation • 215-1243 Rev. E; EN 08-805 4/24/08

Installation Instructions

Step 1: Rough in

Note: See Figure 1a below (for Standard Height) and Figure 1b on page 6 (for Juvenile Height)

when roughing in the Express®.

IMPORTANT: Flush the supply lines before making connections. Debris in supply

lines will cause the valves to malfunction.

IMPORTANT: Dimensions shown in Figure 1a are for a Standard Height

Express® only.

1. Rough in 1/2" NPT hot and cold supply lines through wall at dimensions shown.

2. Rough in 1-1/2" NPT drain waste connection through wall at dimensions shown.

(MM)

32"

(813)

28-5/8"

(727)

25"

(635)

11-3/8"

(289)

19-5/8"

(498) (6) 3/8" WALL ANCHORS

WITH MINIMUM PULL-

OUT RATING OF 1,000

LBS.

23-1/2"

(597) 9-3/8"

(238)

2-3/4"

(70)

13-1/2"

(343) 1" (25)

23-1/2"

(597)

9-3/8"

(238)

(76)

1/2" NPT HOT AND

COLD SUPPLIES,

OR TEMPERED

SUPPLY - STUB

OUT 2" (50) FROM

WALL

FINISHED

FLOOR

CENTERLINE

15-1/4"

(387)

1-1/2" NPT DRAIN -

STUB OUT 2" (50)

FROM WALL

110 Volt GFCI

ELECTRICAL

OUTLET

Figure 1a

Installation Instructions continue . . .

SS-2/IR/STD Express® Lavatory System Dimensions

Standard Height Mounting

Express® Lavatory System SS-Series

SS-2/IR/STD, SS-2/IR/JUV Installation - Obsolete

4/24/08 Bradley Corporation • 215-1243 Rev. E; EN 08-805

(MM)

28"

(711)

24-5/8"

(625)

21"

(533)

11-3/8"

(289)

15-5/8"

(397) (6) 3/8" WALL ANCHORS

WITH MINIMUM PULL-

OUT RATING OF 1,000

LBS.

23-1/2"

(597) 9-3/8"

(238)

2-3/4"

(70)

13-1/2"

(343) 1" (25)

23-1/2"

(597)

9-3/8"

(238)

(76)

1/2" NPT HOT AND

COLD SUPPLIES,

OR TEMPERED

SUPPLY - STUB

OUT 2" (50) FROM

WALL

FINISHED

FLOOR

CENTERLINE

15-1/4"

(387)

1-1/2" NPT DRAIN -

STUB OUT 2" (50)

FROM WALL

110 Volt GFCI

ELECTRICAL

OUTLET

Figure 1b

Installation Instructions continue . . .

SS-2/IR/JUV Express® Lavatory System Dimensions

Juvenile Height Mounting

Express® Lavatory System SS-Series

Installation - Obsolete SS-2/IR/STD, SS-2/IR/JUV

Bradley Corporation • 215-1243 Rev. E; EN 08-805 4/24/08

Installation Instructions continued . . .

Step 1: Rough in continued . . .

IMPORTANT: Turn OFF electrical power to the outlet when installing the

Express®.

3. Install the 110 volt GFCI electrical outlet per local code at the location shown in Figure 2.

4. Install (6) 3/8" wall anchors with a minimum pull-out rating of 1,000 lbs. (supplied by

installer) at the locations shown in Figures 1a or 1b on pages 5-6.

NOTE: The anchors will be used to mount the Express® bowl and frame to the wall.

Installation Instructions continue . . .

1-1/2" NPT DRAIN -

STUB OUT

110 Volt GFCI

ELECTRICAL

OUTLET

1/2" NPT HOT AND

COLD SUPPLIES

OR TEMPERED

SUPPLY - STUB

OUT

Figure 2

Express® Lavatory System SS-Series

SS-2/IR/STD, SS-2/IR/JUV Installation - Obsolete

4/24/08 Bradley Corporation • 215-1243 Rev. E; EN 08-805

Installation Instructions continued . . .

Step 2: Mounting frame to wall

1. Remove the eight Torx-head screws securing the panel to the frame, and remove the panel

(see Figure 3).

Note: Scuff panel does not need to be removed.

2. Position the frame against the wall, ensuring that it is level. If necessary, insert shims under

the frame until level.

Note: When mounted, the Standard and Juvenile Height frames should rest on the floor.

IMPORTANT: Anchoring the frame to a wall that is not flat may cause the frame

to bend. If necessary, install shims to compensate for any wall

distortion.

3. Ensure that the back of the frame is flat against the wall. If wall is not flat, insert shims

behind the frame to ensure that it will not bend when anchored.

4. Once you have positioned the frame such that it is level and resting on the floor, and flat

against the wall or shimmed, use four 3/8" bolts and washers to mount the frame to the wall

(see Figure 4).

Figure 4

(4) 3/8" BOLT

AND WASHER

FRAME

Figure 3

PANEL FRAME

(8) TORX-HEAD

SCREW

SCUFF

PANEL

(do not

remove)

Express® Lavatory System SS-Series

Installation - Obsolete SS-2/IR/STD, SS-2/IR/JUV

Bradley Corporation • 215-1243 Rev. E; EN 08-805 4/24/08

Installation Instructions continue . . .

Installation Instructions continued . . .

Step 3: Installing bowl assembly

IMPORTANT: Moving and positioning the bowl will require more than one person.

Note: Refer to Figure 5 below when installing the bowl assembly.

1. With someone to assist you, place the bowl assembly squarely onto the frame.

2. Attach the front of the bowl assembly to the frame using the two 1/4"-20 x 3/8" pan-head

screws and washers. Do not tighten screws at this time.

IMPORTANT: When bolting the bowl assembly to the frame and wall, do not over-

tighten bolts. Overtightening bolts can damage the Terreon® material.

3. After the bowl assembly is attached to the frame, use two 3/8" bolts and washers (supplied

by the installer) to bolt the bowl to the wall anchors.

4. Tighten the screws installed in procedure #2 above to secure the bowl assembly to the frame.

Do not overtighten.

Figure 5

3/8" BOLT

AND

WASHER

BOWL ASSEMBLY

BACK VIEW

3/8" BOLT

AND

WASHER

1/4"-20 X 3/8"

PAN HEAD

SCREWS AND

WASHERS

Express® Lavatory System SS-Series

SS-2/IR/STD, SS-2/IR/JUV Installation - Obsolete

4/24/08 Bradley Corporation • 215-1243 Rev. E; EN 08-805

Installation Instructions continued . . .

Step 4: Connecting supply and drain

1. FOR HOT AND COLD SUPPLY: Connect the flexible hoses installed to the Vernatherm™

Mixing Valve to the hot and cold water supply piping from the wall (see Figure 6a).

Note: The red marking on Vernatherm™ Mixing Valve indicates hot water supply inlet.

FOR SINGLE TEMPERED SUPPLY: Attach the stop/check/strainer to the 1/2" tempered supply

line. Connect the stop/check/strainer to the solenoid valves with the flexible supply hose (see

Figure 6b).

2. Install the drain plug in the hole in the bottom of the bowl (see Figure 7).

3. Beneath the bowl, install the 1/4" rubber washer onto the drain plug, and thread the tailpiece

to the drain plug.

4. Assemble the P-trap by connecting the 1-1/2" tubular pipe to the tailpiece and to the 1-1/2"

drain pipe stubbed out of the wall.

5. Install the strainer on the drain plug opening inside the bowl, and push the strainer firmly

into place.

Figure 7

Figure 6a

FLEXIBLE

SUPPLY

HOSE VERNATHERM™

THERMOSTATIC

MIXING VALVE

FLEXIBLE

SUPPLY

HOSE

CONNECT TO

1/2" NPT COLD

WATER SUPPLY

CONNECT TO

1/2" NPT HOT

WATER SUPPLY

FLEXIBLE

SUPPLY HOSE

(TO SOLENOID

BRACKET)

Figure 6b

STOP/STRAINER/CHECK

VALVE (S60-003)

90° ELBOW

169-639

1/2 NIPPLE

(113-006DJ)

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Bradley Sanitärprodukte Handbücher

Bradley

Bradley Express MG Series Bedienungsanleitung

Bradley

Bradley Express SS-Series Express SS-3N/BIR3/STD Bedienungsanleitung

Bradley

Bradley Sentry SN2003/AST4 Bedienungsanleitung

Bradley

Bradley S45-1986 Bedienungsanleitung

Bradley

Bradley Terreon TDB3104 Bedienungsanleitung

Bradley

Bradley S19-304GA Bedienungsanleitung

Bradley

Bradley S19294 Series Bedienungsanleitung

Bradley

Bradley S19-310DCFW Bedienungsanleitung

Bradley

Bradley S19-460EFW Bedienungsanleitung

Bradley

Bradley S19-220ABF Bedienungsanleitung

Bradley

Bradley S24-210 Bedienungsanleitung

Bradley

Bradley Corner-Fount MF2922 Kurzanleitung

Bradley

Bradley Advocate AV Series Bedienungsanleitung

Bradley

Bradley S19-430EH Bedienungsanleitung

Bradley

Bradley Express MG Series Bedienungsanleitung

Bradley

Bradley S19-220DCSS Bedienungsanleitung

Bradley

Bradley S19-270C Bedienungsanleitung

Bradley

Bradley S19-230 Bedienungsanleitung

Bradley

Bradley S19-125SBF Bedienungsanleitung

Bradley

Bradley Verge Crestt Series Kurzanleitung

Bradley

Bradley S19-120SSBF Bedienungsanleitung

Bradley

Bradley S19-120FMBF Bedienungsanleitung

Bradley

Bradley S19-270C Bedienungsanleitung

Bradley

Bradley S19-430A Bedienungsanleitung

Beliebte Sanitärprodukte Handbücher anderer Marken

Weka

Weka 506.2020.00E Betriebsanleitung

American Standard

American Standard DetectLink 6072121 Bedienungsanleitung

Kohler

Kohler K-6228 Montageanleitung

Uponor

Uponor Contec TS Bedienungsanleitung

Pfister

Pfister Selia 49-SL Bedienungsanleitung

Fortis

Fortis VITRINA 6068700 Bedienungsanleitung

Kohler

Kohler K-12183 Montageanleitung

Maxxus

Maxxus MX-M206-01 Bedienungsanleitung

Viega

Viega Prevista Pure 8512 Bedienungsanleitung

Kohler

Kohler Centerset K-15240 Montageanleitung

Viega

Viega Prevista Dry 8522.33 Bedienungsanleitung

Sanela

Sanela Lema SLP 59RB Bedienungsanleitung

Elkay

Elkay EDF15AC Installationshandbuch

Hans Grohe

Hans Grohe AXOR Citterio E 36702000 Handbuch

baliv

baliv WT-140 Bedienungsanleitung

Kohler

Kohler Mira Eco Bedienungsanleitung

BELLOSTA

BELLOSTA romina 0308/CC Bedienungsanleitung

Bristan

Bristan PS2 BAS C D2 Verdrahtungsschema