Bristan CAP2 SHXAR C (D6) Verdrahtungsschema

Installation Instructions

& User Guide

Please leave these instructions

with the end user

Pack Contents

Maximum Static Pressure: 10.0 bar

Max: 5.0 bar

Prior to Installation

Spares

Flat Head

Screwdriver

Socket Spanner

Safety Goggles

Drill

Cross Head

Screwdriver

Pipe Cutter

Long Nosed Pliers Electronic Detector

2.5mm

10mm

Hexagonal Keys

Adjustable Spanner

Operation

Dynamic Water Pressure

Speciﬁcations

25°C

5°C

Min 5°C; Max 25°C

Inlet Water Temperature Inlet Connections

Tools Required

All products manufactured and supplied by Bristan are safe to use provided that they are installed, operated and receive regular

maintenance in accordance with these instructions.

This product needs to be installed in accordance with, and meet the requirements of The Water Supply (Water Fittings) Regulations

(Northern Ireland) 2009 and The Water Supply (Water Fittings) (Scotland) Byelaws 2014. For full Installation Requirements & Notes

(IRN) please visit www.wrasapprovals.co.uk/approvals-directory

Before installing this product the water supply must be thoroughly ﬂushed in order to remove any swarf, solder etc. Full access must be

made available for future maintenance/servicing purposes. Isolation valves must be ﬁtted to the inlet water supplies to ensure ease of

future maintenance.

Before drilling into walls, check that there are no hidden electrical wires, cables or water supply pipes. This can be checked with the aid of

an electronic detector. If power tools are used do not forget to: - Wear eye protection - Unplug equipment after use

This product must not be modiﬁed in any way as this will invalidate the guarantee.

Min: 0.1 bar

CAP2 SHXAR C (D6)

x2 End Caps

Single

Function

Handset

Long

Elbows

Riser

Brackets

Shower Valve

Cone

Nut

Hose

Slider

Hose

Retainer

Screw

Pack

Olives

Nuts

Plinths

x2 x1

1.0

2.0

5.0

4.0

3.0

Pressure

BAR

65°C

60°C

Recommended 60°C;

Max 65°C

IMPORTANT

The inlet hot water must

be at least 10°C above the

required blend temperature.

Factory

pre-set 42°C

110-155mm

Centres

15mm

Compression

Inlet Dimensions

HP-SE & LP-SE

TMV2 Designation

Increase

Temperature

and Flow

O

30mm

To replace any

spare parts for

your shower, why

not scan the

QR Code or visit

www.bristan.com

and search for

your product.

Please keep this booklet for future

reference.

Installer, when you have read these

instructions please ensure you leave

them with the user.

Installation Instructions

and User Guide

Exposed Sequential and

Concentric Mini Valve Showers

Contents

• Important Safety Information 3

• Installation Requirements 4-7

• Prior to Installation 8-9

• Installation 10

• General Cleaning 11

• Maintenance 12-16

• Troubleshooting 17

• Notes 18-19

2Need help? Give us a call on 0330 026 6273 and speak to one of our trained advisors.

Contents

Thank you for choosing Bristan, the UK’s leading taps and showers expert. We have

designed this product with your enjoyment in mind. To ensure that it works to its

full potential, it needs to be ﬁtted correctly. These ﬁtting instructions have been

created to give you all of the information you need and, if you need any further help,

please do not hesitate to give us a call on 0330 026 6273.

Please make sure you read these instructions and retain for future use.

All products manufactured by Bristan are safe, providing they are installed and used

correctly and also receive maintenance when needed.

These ﬁttings, including the connecting water and waste system need to be installed

in accordance with and meet the requirements of the Water Supply Regulations 1999

(Water Fittings) and current by-laws. If you are in doubt about your ability to install

this product correctly or safely, you should employ the services of an experienced

qualiﬁed plumber.

This product must not be modiﬁed in any way otherwise this will invalidate the

guarantee. Remove all packaging and check the contents for damage before starting

installation.

Warning: Before installing the new mixer valve it is essential that you thoroughly

ﬂush through the pipework in order to remove any remaining swarf,

solder, etc. Failure to carry out this procedure could cause problems or

damage to the workings of the mixer tap.

Fitting isolating valves to the inlet feeds is required for ease of maintenance.

Warning: Do not operate the mixer if you suspect it is frozen. Do not site the mixer

valve where it might be subjected to freezing conditions.

Consider the following whilst using power tools:

• Prior to drilling into walls, check there are no hidden electrical cables or

wires and there are also no water pipes. These can potentially be found

using an electrical or metal detector. You may also need to know some

of the schematics of previous installations to determine the suitability

and accommodation of the installation.

• Wear the correct PPE, especially ear, eye and hand protection

when using power tools. Unplug any mains equipment after use.

• Keep electrical equipment away from sources of water.

• If a blow-lamp is used when plumbing, the ﬂame must be kept well away from

the product otherwise damage may occur.

If in doubt, contact a registered plumber, your Local Water Authority or the

Secretary of The Institute of Plumbing, address as follows;-

The Institute of Plumbing,

64 Station Lane,

Hornchurch,

Essex, RM12 6NB

Tel:01708 472791

Need help? Give us a call on 0330 026 6273 and speak to one of our trained advisors.

Important Safety Information

Please refer to your speciﬁc shower

contents page for speciﬁcation

information.

These showers are designed to be used

in conjunction with the kit supplied, or

Bristan shower kits where not supplied.

We cannot guarantee compatability or

adequate performance when used with

other kits. This would also invalidate your

guarantee. Please refer to the installation

manual supplied with your Bristan

shower kits for their speciﬁcation

information.

This shower valve must be installed

in compliance with current water

regulations. If you have any doubts

about the water regulation requirements

contact your local water services

provider or use the services of a

professional plumber.

This shower valve is suitable for use with

the following water supply systems:

• Gravity Fed Hot and Cold

(pressure imbalance should not exceed

a ratio of 5:1 - see Speciﬁcation section)

• Gravity Fed Hot and Mains Cold

(pressure imbalance should not exceed

a ratio of 5:1 - see Speciﬁcation section)

• Instantaneous water heater

(combination boiler)

• Unvented System

• Pumped System

Important: If you install this shower valve

with a gravity fed system, there must be a

minimum head (vertical distance) from the

underside of the cold water storage tank

to the outlet of at least 1 metre .

Note: Pumped system (with Essex ﬂange)

If you install this shower valve to a pumped

gravity fed system where the minimum

head (vertical distance) from the underside

of the cold water storage tank to the top

of the hot water cylinder is less than 1

metre we recommend an Essex ﬂange is

used as shown.

Flushing Pipe-work

Important: Before connecting the shower

valve, the supply pipe-work must be

ﬂushed to clear debris before connecting

the shower. Debris will reduce the

performance and life of the mixer.

4Need help? Give us a call on 0330 026 6273 and speak to one of our trained advisors.

Installation Requirements

Gravity Fed Hot and Cold Gravity Fed Hot and Mains Cold

cold mains supply cold mains supply

1m min.

min.

Key: Isolating

Valve

Reducing

Valve

Shower

Valve Pump Essex

Flange

Need help? Give us a call on 0330 026 6273 and speak to one of our trained advisors.

Installation Requirements

Unvented System

Instantaneous Water Heater

Pumped System

cold mains supply

Pumped System (with Essex ﬂange)

cold mains supply

1m min.1m min.

50mm

If less

than

1m see

note.

Key: Isolating

Valve

Reducing

Valve

Shower

Valve Pump Essex

Flange

6Need help? Give us a call on 0330 026 6273 and speak to one of our trained advisors.

Installation Requirements

This ﬁtting needs to be installed in

accordance with the following Installation

Requirements and Notes (IRN) to ensure

they meet the requirements of the Water

Supply (Water Fittings) Regulations 1999

and the Scottish Byelaws 2004.

IRN R001: See text of entry for

Installation Requirements or Notes.

IRN R040 - Schedule 2-15 (1): The

ﬁtting shall be installed so that its outlet

discharges above the spill-over level of

any ﬁxed appliance as indicated below:-

For backﬂow protection in domestic or

installations up to, and including, Fluid

Category 3.

If the ﬁtting cannot be installed as

indicated in the table opposite it shall be

installed as either a or b below:

a: with an approved double check valve

assembly or some other no less eective

backﬂow prevention device immediately

upstream of the inlet.

b: so that it draws water by gravity

only from a cistern, or cylinder having

a permanently open vent pipe, and

the distributing pipe supplies no other

ﬁttings (other than a draining tap) at a

lower level.

For backﬂow protection in premises or

installations up to, and including Fluid

Category 5.

The vertical distance of the outlet above

the spill-over level shall be not less than

20mm or twice the diameter of the inlet

pipe to the ﬁtting, which ever is the

greater. If the ﬁtting cannot be installed

as indicated it shall be installed with

a backﬂow prevention arrangement

suitable for the Fluid Category.

Size of tap or

combination

ﬁtting

Vertical distance

of outlet above

spill-over level

1. Not exceeding

½” 20mm

2. Exceeding ½”

but not

exceeding ¾”

25mm

3. Exceeding ¾” 70mm

Need help? Give us a call on 0330 026 6273 and speak to one of our trained advisors.

Installation Requirements

Supply System Flow Regulator Comments

Hot Supply Cold Supply Hot Supply Cold Supply

0.1 - 1.0 bar 0.1 - 1.0 bar Not Required Not Required

Maximum pressure

loss ratio 5:1 between

inlets

1.0 - 5.0 bar

or pumped

1.0 - 5.0 bar

or pumped Yellow (5 litre) Green (7 litre)

Optional, can be used

if water economy

is required

Gravity Fed

0.1 - 0.5 bar

Mains 1.0 - 10

bar

Not Required Green (7 litre)

Gravity Fed

over 0.5 bar Yellow (5 litre) Green (7 litre)

Unvented

Mains/ Mains

Pressurised

Yellow (5 litre) Green (7 litre)

Instantaneous

Water Gas

Heater

Yellow (5 litre) Green (7 litre)

It may not be

necessary on some

gas water heaters to

have a ﬂow regulator

on the hot

water supply.

Instantaneous

Water Electric

Heater

Not Required Yellow (5 litre)

It is a requirement that

a stable ﬂow of water

passes through the

heater. This can be

achieved by ﬁtting a

ﬂow stabiliser before

the heater. The heater

temperature should

also be adjusted

to 45-50°C

Any vented

(open outlet)

Heater

Gas/Electric

e.g.

Electric

Shower

Do not use mixer valves with this type of water system;

this would be extremely dangerous!

Flow regulators have been pre-ﬁtted to this product for water eciency.

If you have low water pressure, or certain water supply systems these may need to be

removed in order to achieve adequate ﬂow. Please see the table to check whether the

ﬂow regulators need to be removed.

8Need help? Give us a call on 0330 026 6273 and speak to one of our trained advisors.

Prior to Installation

1. Unscrew both inlet elbows

anti-clockwise from the

valve body.

2. Remove the ﬂow regulators

using long-nosed pliers.

3. Screw the inlet elbows

clockwise to ﬁt back into

the valve body.

To Remove/Replace Flow Regulators:

Conﬁguring the Inlet Elbows:

The shower valve is supplied with two

small and two large elbows that can

adjust between 110-155mm.

The elbows can be pointed to feed from

the top, bottom or rear.

Two full turns are required to ﬁt the elbow

into the body properly.

1. Unscrew both inlet elbows

anti-clockwise from the valve body.

2. Choose the elbow conﬁguration

to suit inlet centres:

* 2x small elbows: 110-130mm

* 1x small, 1x large: 130-136mm

* 2x large: 136-155mm

3. Screw in the desired elbows clockwise

for two complete turns to ﬁt. This will

set to largest possible centre

measurement.

4. The elbows can be screwed a maximum

of 1.5 turns after ﬁtting for adjustment.

Screw further clockwise to reduce the

centre measurement; anti-clockwise to

increase.

To Adjust Elbows:

110-155

Centres

Flow Regulator

Need help? Give us a call on 0330 026 6273 and speak to one of our trained advisors.

Prior to Installation

Inhaltsverzeichnis

Andere Bristan Sanitärprodukte Handbücher

Bristan

Bristan N2 SHC3STP G Verdrahtungsschema

Bristan

Bristan HOU SHCDIV C (D7) Verdrahtungsschema

Bristan

Bristan W BASIN13 C Verdrahtungsschema

Bristan

Bristan W BASIN14 C Verdrahtungsschema

Bristan

Bristan CR SHXDIVFF C Montageanleitung

Bristan

Bristan W BASIN01 C Verdrahtungsschema

Bristan

Bristan Java Eco Click J EBAS C Bedienungsanleitung

Bristan

Bristan Quadrant Riser Rail kit Bedienungsanleitung

Bristan

Bristan KN2 SHXAR C Montageanleitung

Bristan

Bristan GLR 1/2 C Bedienungsanleitung

Bristan

Bristan W BASIN12 C Bedienungsanleitung

Bristan

Bristan WMNT12 Montageanleitung

Bristan

Bristan JAVA J BSM E8 C Bedienungsanleitung

Bristan

Bristan Jute JU PBSM C Bedienungsanleitung

Bristan

Bristan Descent DSC BAS C Montageanleitung

Bristan

Bristan TY2 SDIV C Montageanleitung

Bristan

Bristan HOU 1HBF C Verdrahtungsschema

Bristan

Bristan Target TG SNK C Bedienungsanleitung

Bristan

Bristan Regency Luxury R BSM C Verdrahtungsschema

Bristan

Bristan TG SNK C Verdrahtungsschema

Bristan

Bristan AR2 SHXVOFF Montageanleitung

Bristan

Bristan VAL2 BIB C 6 CD Verdrahtungsschema

Bristan

Bristan IRBS1-CP Montageanleitung

Bristan

Bristan W BATH07 C Verdrahtungsschema

Beliebte Sanitärprodukte Handbücher anderer Marken

Weka

Weka 506.2020.00E Betriebsanleitung

American Standard

American Standard DetectLink 6072121 Bedienungsanleitung

Kohler

Kohler K-6228 Montageanleitung

Uponor

Uponor Contec TS Bedienungsanleitung

Pfister

Pfister Selia 49-SL Bedienungsanleitung

Fortis

Fortis VITRINA 6068700 Bedienungsanleitung

Kohler

Kohler K-12183 Montageanleitung

Maxxus

Maxxus MX-M206-01 Bedienungsanleitung

Viega

Viega Prevista Pure 8512 Bedienungsanleitung

Kohler

Kohler Centerset K-15240 Montageanleitung

Viega

Viega Prevista Dry 8522.33 Bedienungsanleitung

Sanela

Sanela Lema SLP 59RB Bedienungsanleitung

Elkay

Elkay EDF15AC Installationshandbuch

Hans Grohe

Hans Grohe AXOR Citterio E 36702000 Handbuch

baliv

baliv WT-140 Bedienungsanleitung

Kohler

Kohler Mira Eco Bedienungsanleitung

BELLOSTA

BELLOSTA romina 0308/CC Bedienungsanleitung

Crosswater

Crosswater Heir 18-31 Bedienungsanleitung