Bristan Descent DSC BAS C Montageanleitung

Please keep this booklet for future

reference.

Installer, when you have read these

instructions please ensure you leave

them with the user.

Installation Instructions

and User Guide

Descent Tap Range

Models Covered:

DSC BAS C, DSC BF C, DSC BSM C,

DSC 1HBF C, DSC FSBSM C

Contents

• Important Safety Information 3

• General Information 4

• Speciﬁcations 4

• Dimensions (mm) 5-7

• Installation Requirements 8

• Installation 9-11

• Maintenance 12-13

• Troubleshooting 13

• Guarantee 14

• Notes 15

Need help? Give us a call on 0330 026 6273 and speak to one of our trained advisors.

Contents

Thank you for choosing Bristan.

These ﬁtting instructions have been created to give you all of the information you

need for a safe and successful installation, so please read them thoroughly and retain

for future reference.

If you need any further help, please do not hesitate to give us a call on 0330 026 6273.

All products manufactured and supplied by the manufacturer are safe to use

provided that they are installed, operated and receive regular maintenance in

accordance with these instructions.

If you are in any doubt about your ability to install this product safely you

must employ the services of an experienced qualiﬁed plumber.

This product needs to be installed in accordance with, and meet the

requirements of the Water Supply (Water Fittings) Regulations 1999 and

current by-laws. For full Installation Requirements & Notes (IRN)

please visit wras.co.uk/directory.

Remove all packaging and check the components for damage before

starting installation. Before starting any installation please consider

the following:

Prior to drilling into walls, check that there are no

hidden electrical wires, cables or water supply pipes.

This can be checked with the aid of an electronic

detector.

If power tools are used do not forget to:

- Wear eye protection

- Unplug equipment after use

Isolation valves must be ﬁtted to the inlet water supplies to ensure ease of

future maintenance.

Before installing this product the water supply must be thoroughly ﬂushed in

order to remove any swarf, solder etc.

This product must not be modiﬁed in any way as this will invalidate

the guarantee.

Full access must be made available for future maintenance/servicing

purposes.

If in doubt, contact a registered plumber or your Local Water

Authority or the Secretary of the Institute of Plumbing, address as follows:-

The Institute of Plumbing,

64 Station Lane,

Hornchurch,

Essex,

RM12 6NB, Tel: 01708 472791

Need help? Give us a call on 0330 026 6273 and speak to one of our trained advisors. 3

Important Safety Information

This product has been designed to comply with BS EN 200 for combination

taps to be used within systems designed to BS 6700.

BS 6700 recommends the temperature of stored water should never exceed

65°C. A stored water temperature of 60°C is considered sucient to meet all

normal requirements and will minimise the build up of lime scale in hard water

areas.

If installing this product on a low pressure (tank fed) system please see

speciﬁcation table below to determine the minimum distance required from

underside of the cold water tank to the outlet.

These taps and mixers should be installed in compliance with the Water

Regulations. Where the supplies are unbalanced, i.e. Hot water from cylinder

tank/cold from the mains, approved check valves must be ﬁtted in the supply

pipes.

For further details contact your Local Water Authority.

P r o d u c t

Code

Working

Pressures Inlet

Minimum distance

from cold water

tank to outlet

(metres)

Min Max

DSC BAS C 0.2 5.0 M10 15mm Compression

Flexible Tails

DSC BF C 0.2 5.0 3/4" BSP Threaded Tail 2

DSC BSM C 0.3 5.0 3/4" BSP Threaded Tail 3

DSC 1HBF C 1.0 5.0 M12 15mm Compression

Flexible Tails

DSC FSBSM C 1.5 5.0 M12 15mm Compression

Flexible Tails

Maximum static pressure: 10.0 bar

System Requirements:

Gravity fed hot & cold (Equal pressures)

Gravity fed hot & cold (Dierential pressure, maximum ratio 5:1)

Unvented systems

Instantaneous water heater (Combination boiler)

4Need help? Give us a call on 0330 026 6273 and speak to one of our trained advisors.

General Information

Speciﬁcations

Dimensions are approximate and in millimetres.

Bath Filler

Basin Mixer

137

180

140

147

107

Need help? Give us a call on 0330 026 6273 and speak to one of our trained advisors. 5

Dimensions (mm)

1 Hole Bath Filler

Dimensions are approximate and in millimetres.

Bath Shower Mixer

137

180

176

209

128

108

6Need help? Give us a call on 0330 026 6273 and speak to one of our trained advisors.

Dimensions (mm)

Dimensions are approximate and in millimetres.

843

375

190

220

Floor Standing Bath Shower

Mixer

Need help? Give us a call on 0330 026 6273 and speak to one of our trained advisors. 7

Dimensions (mm)

Flexible Connecting Pipes

Care must be taken when connecting the ﬂexible connection pipes to the household

pipework to ensure they do not bend sharply and kink or twist.

See below for recommended ways to ﬁt the ﬂexible connecting pipes.

Slight

bend

90°

Angle

Kink Curved

round

Twists

Important: Failure to follow these guidelines may result in poor performance

and damage to the ﬂexible connecting pipes.

Important: Full access must be made available on installation for future

maintenance/ servicing purposes.

8Need help? Give us a call on 0330 026 6273 and speak to one of our trained advisors.

Installation Requirements

Basin Mixer / 1 Hole Bath Filler

1. Screw the ﬂexi tails into the bottom

of the body by hand only (DO NOT

OVERTIGHTEN).

2. Feed the ﬂexi tails through the

hole in the basin / bath, ensuring

the washer is ﬁtted between the tap

body and ﬁxing surface to ensure a

water tight seal.

3. Screw the ﬁxing rods into the

bottom of the tap body. Slide the 'C'

shaped rubber washer and 'C' shaped

metal washer onto the ﬁxing rods up

to the underside of the basin/bath.

4. To secure the tap body in place

tighten the ﬁxing nuts onto the

ﬁxing rods until the are fully

tightened against the 'C' shaped

metal washer. The ﬁxing nuts can be

tightened with a suitable spanner.

5. Connect the ﬂexible tails to the hot

and cold water supplies.

6. Turn on both water supplies,

operate the handle in both directions,

letting the water ﬂow for a few

minutes to ﬂush through the system.

7. Fit the clicker waste (for basin

mixer only) ensuring the rubber

washer is ﬁtted between the basin

and the waste. Place the other rubber

washer under the basin and secure

by tightening the backnut, in order to

ﬁll the basin, the button in the middle

of the waste needs to be pressed

down. To release the water, press the

button again.

8. Check all joints and connections

for any leaks.

Need help? Give us a call on 0330 026 6273 and speak to one of our trained advisors. 9

Installation

Bath Filler and Bath Shower Mixer

1. Fit the tap body to the bath ensuring

that the washers are ﬁtted between the

body and the bath to create a water

tight seal.

2. Secure the body to the bath using the

washers and metal backnut. Tighten the

backnuts onto the threaded tails.

A suitable spanner may be required to

fully tighten the backnuts.

3. Connect the hot and cold water

supplies to the threaded tails using

a ¾” BSP connector (not supplied).

4. Bath Shower Mixer only - ﬁt the

shower hose to the hose outlet using

the small sealing washer, and the

handset to the hose using the small

washer.

Important: Prior to the drilling into

walls, check there no hidden electrical

wires, cables or water supply pipes with

the aid of an electronic detector.

If you use power tools do not forget to:

• Wear eye protection

• Unplug equipment after use

Fit the wall bracket (not shown) to the

wall using the ﬁxings supplied, ensuring

the handset and hose reaches it.

5. Turn on both water supplies and turn

both handles to the on position, letting

the water ﬂow for a few minutes.

6. Check all joins and connections for

any leaks.

7. To switch from bath to shower mode,

pull the diverter knob up and turn, to

revert back to bath ﬁlling mode push

the diverter knob back down.

10 Need help? Give us a call on 0330 026 6273 and speak to one of our trained advisors.

Installation

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Bristan Sanitärprodukte Handbücher

Bristan

Bristan Prism Eco Click Bedienungsanleitung

Bristan

Bristan PM2 SHCDIV BLK (D2) Verdrahtungsschema

Bristan

Bristan Java J BASNW C Bedienungsanleitung

Bristan

Bristan W BASIN08 C Verdrahtungsschema

Bristan

Bristan GLD2 BF C (D1) Verdrahtungsschema

Bristan

Bristan Rio Bedienungsanleitung

Bristan

Bristan SK1850- SK1850-2 Original Betriebsanleitung

Bristan

Bristan FIXED HEADS FHC ABRD01 C Bedienungsanleitung

Bristan

Bristan Star FH STRD01 C Bedienungsanleitung

Bristan

Bristan 1901 Bedienungsanleitung

Bristan

Bristan Opac Series Montageanleitung

Bristan

Bristan GLL FLEXSNK C (D1) Verdrahtungsschema

Bristan

Bristan QD SHXSMFF C D3 Verdrahtungsschema

Bristan

Bristan Quest Bedienungsanleitung

Bristan

Bristan Quadrant Riser Rail kit Bedienungsanleitung

Bristan

Bristan EV KIT-EFB C Montageanleitung

Bristan

Bristan Body Jet JET2 C Bedienungsanleitung

Bristan

Bristan IRN R001 Bedienungsanleitung

Bristan

Bristan QST BSM C (D5) Verdrahtungsschema

Bristan

Bristan DSC 3HBF C Bedienungsanleitung

Bristan

Bristan Descent Series Bedienungsanleitung

Bristan

Bristan W BASIN01 C Verdrahtungsschema

Bristan

Bristan RO2 SHXAR C Montageanleitung

Bristan

Bristan Joy care Montageanleitung

Beliebte Sanitärprodukte Handbücher anderer Marken

Weka

Weka 506.2020.00E Betriebsanleitung

American Standard

American Standard DetectLink 6072121 Bedienungsanleitung

Kohler

Kohler K-6228 Montageanleitung

Uponor

Uponor Contec TS Bedienungsanleitung

Pfister

Pfister Selia 49-SL Bedienungsanleitung

Fortis

Fortis VITRINA 6068700 Bedienungsanleitung

Kohler

Kohler K-12183 Montageanleitung

Maxxus

Maxxus MX-M206-01 Bedienungsanleitung

Viega

Viega Prevista Pure 8512 Bedienungsanleitung

Kohler

Kohler Centerset K-15240 Montageanleitung

Viega

Viega Prevista Dry 8522.33 Bedienungsanleitung

Sanela

Sanela Lema SLP 59RB Bedienungsanleitung

Elkay

Elkay EDF15AC Installationshandbuch

Hans Grohe

Hans Grohe AXOR Citterio E 36702000 Handbuch

baliv

baliv WT-140 Bedienungsanleitung

Kohler

Kohler Mira Eco Bedienungsanleitung

BELLOSTA

BELLOSTA romina 0308/CC Bedienungsanleitung

Crosswater

Crosswater Heir 18-31 Bedienungsanleitung