Broseley Lincoln Handbuch

200704_3

Installation & Operating Instructions

Model(s): Lincoln, Canterbury & Stamford

Conventionally Flued Natural Gas Stoves

PLEASE LEAVE THESE INSTRUCTIONS WITH THE USER

Chimney closure plates are not supplied

Please note gas installations MUST only be carried out by installers who

are Gas Safe registered.

200704_3 2

Contents

Introduction 3

Packing List 3

Specification 4

Dimensions 4

Hearth Requirements 5

Chimney Requirements 6

Assembly

Burner Installation 7

Connecting the TTB Device and Fitting the Reflective Rear Plate 8

Positioning the Coals 9

Gas Connection & Pressure Testing 10

Spillage Testing 13

Operating the Stove 14

Curing the Paint 15

Trouble-shooting 16

Servicing Instructions 17

Commissioning Form 18

Guarantee 19

200704_3 3

Introduction

THANK YOU FOR PURCHASING A BROSELEY GAS FIRED STOVE

Broseley Fires Ltd, a family run company, was founded as an appliance and

design development company in 1975.

Since then we have built up an enviable reputation for the quality, reliability and

fuel efficiency of our stoves.

These instructions have been carefully prepared to guide the installer and end-

user through the relevant methods and standards for installation of your new Gas

Stove.

Correctly installed and operated, your stove will give you many years of warmth

and reliability. Therefore, we would suggest that you read the whole instruction

manual prior to handing it to your installer. That way you will have a clearer

picture of what is involved.

It is required by law that the complete assembly, installation and commissioning

of gas-fired stoves is carried out by a professionally qualified and accredited gas

fitter listed on the “Gas Safe” register.

THE INSTALLATION MUST BE IN ACCORDANCE WITH THE ‘GAS SAFETY

INSTALLATION AND USE REGULATIONS’ IN CONJUNCTION WITH THESE

INSTRUCTIONS AND THE RELEVANT ‘BRITISH STANDARDS CODES OF

PRACTICE’ REQUIREMENTS AND THE RELEVANT ‘LOCAL AND NATIONAL

BUILDING REGULATIONS’. A COMMISSIONING CERTIFICATE MUST BE

LEFT WITH THE END CUSTOMER UPON FINAL COMPLETION AND THE

COMMISSIONING FORM COMPLETED IN THE BACK OF THESE

INSTRUCTIONS.

PackingList

Burner Box Stove Box

1 x Burner unit 1 x Cast iron stove body

1 x Stainless reflector Plate 4 x Legs & bolts

2 x Large coal matrix 1 x Flue spigot

4 x Small front coals

14 x Small loose coals Canterbury Only

1 x Instruction booklet 1 x Handle (inc Allen bolt and grub screw)

4 x Burner fixing and screws

(2 x Self Tapping to hold to the rear of the stove)

2 x Spacers for burner

3 x Self Tapping Screws (for the reflector plate)

4 x Self tapping screws (for spigot connection)

4 x Washers

200704_3 4

Specification

Heat Input (Gross) 5.5kW

Gas Category I2H

Supply Pressure 20 mbar

Gas Rate 0.66 m3/hr

Injector Size 360

Spigot diameter 125mm (5”)

Country of destination GB, IE

Efficiency Class 1

Please note this product is designed to only use natural gas G20.

Dimensions

Lincoln – Weight 64Kg

Canterbury – Weight 66Kg

All dimensions are in millimetres.

200704_3 5

Hearth Requirements

The appliance needs to be located onto a solid non-combustible hearth with a

minimum thickness of 12mm. The hearth must be capable of withstanding the

weight of the appliance.

To ensure correct combustion the following minimum clearances must be

adhered to:

Inglenook Installation Freestanding Installation

Please note these are minimum clearances, whenever possible it is advisable to

have as much clearance as possible around the stove for easy access and

maintenance.

Please note the gas supply connection to the appliance is in the centre

underneath the stove. The connection requires an 8mm-diameter semi-rigid

pipe, not more than 1 meter in length.

Stove Clearances AB C Above

Non-Combustible 25mm 75mm 50mm 100mm

Combustible N/A 610mm 610mm 610mm

200704_3 6

Chimney Requirements

Class 1 Chimney Example

Above is a typical example of an installation with a class 1 flue, please note we do not

supply chimney closure plates. The appliance can be installed in any adequate area

suitable for solid fuel fires and stoves. It can use a class 1, class 2 and pre-cast flue.

For pre-cast flue installations it is ESSENTIAL that a sealed connection is made into the

actual flue system (a void behind the closure plate is not permitted). Please refer to the

codes of best practice for further advice on pre-cast flue’s. The 150mm pipe supplied

can be cut down in length but CANNOT be extended.

Before you install the stove, make sure the chimney flue outlet is correctly positioned to

align with the flue outlet on the stove and that the chimney is in good condition. If not, a

chimney liner must be installed or a suitable class II gas flue used. A draught is

necessary to ensure the products of combustion are fully evacuated. Due to the internal

dilution/diversion system in the stove, it is not obligatory to line the chimney but local

conditions will apply. The flue will have to be inspected by a Gas Safe registered installer

and passed as suitable/sound.

Ideally it is recommended that a minimum height of 610mm from the stove should be

established before any significant changes of the direction of the flue. Horizontal or

negative gradients should be avoided. The flue must have a minimum height of 3 metres

to insure adequate draught.

Prior to installation, the installer should insure that the flue is free from obstruction and

any dampers must be fixed in a permanently open position. Ensure the chimney is not

closed and that it has been swept and subsequently smoke tested.

Make sure that rain, birds or any foreign body cannot get into the chimney to cause

damage or blockage. This problem can normally be overcome by fitting an approved gas

cowl. It is essential for the effective running of your stove that the chimney draws

properly to allow the products of combustion to escape.

Closure

Plate

Lintel

Void

Dimensions

A = 250mm Min.

B= 50mm Min.

C = 50mm Min.

D = 25mm Min.

Figure 1

200704_3 7

Assembly - Burner Installation

Ensure all components are present prior to commencing assembly (See Packing

List on page 3). You will need a short pozi-drive screwdriver and a set of

spanners. On the Lincoln the gas burner is fitted into the stove body through the

top of the stove (by removing the lid). On the Canterbury you can fit the burner

through the main door (by unwinding the handle anti clockwise).

1) Remove the stove body from its packaging and lay it down on its back.

2) Attach the four legs using the supplied bolts.

3) Stand the stove up on its legs. On the Lincoln & Stamford remove the lid by un-doing

the four fixing bolts. For the Canterbury simply open the main door.

4) Insert the burner into the stove locating the burner bracket on to the fixing lugs

provided. Insert the burner end with the control knob first followed by the other end of

the burner locating the burner bracket onto the up stands provided. Please note with

the Lincoln and Stamford models 2 spacers are required. These spacers are to be

located on top of the lugs and under the burner brackets (2 off additional washers

are required on top of the spacers before securing the burner to the fixing lugs). The

longer screws are then used. Use the burner fixing screws and 2 off washers to

secure the burner in place.

5) Next fix the rear of the burner bracket to the rear of the stove (dilution box) using the

self tapping screws provided.

200704_3 8

Assembly - Fitting TTB sensor

With the burner installed, thread the wires running from the TTB device (mounted

on the rear panel of the stove) down to the 6.3mm spade receptacle connectors

on the thermocouple interrupter (Located at the rear of the Gas top assembly),

These wires can be installed either way round on the terminals by loosening the

thermocouple connection, after the spades have been connected the

thermocouple nut needs to be tightened.

Assembly - Fitting the Reflective Rear Plate

After fixing the burner in position fit the stainless reflector plate to the rear of the

stove (dilution box) using the holes and fixing screws supplied. Although the plate

can be fitted into the Canterbury through the door, removing the lid will make

things easier if you have any difficulties.

Remove the protective film once the plate has been fitted.

To insert the reflective plate into the stove insert the bottom of the plate first, then

give the plate a slight bend inwards on both sides and finally bring the top of the

plate into place. The reflector plate simply drops down through the top of the

stove and is then secured in place using the fixings provided.

200704_3 9

Assembly - Positioning the Coals

Only the ceramics supplied with this appliance should be used. The ceramics

should only be laid as described. Before any ceramics are placed in position

ensure that the pilot is not obstructed and the burner is operating correctly.

Broseley Fires Ltd accepts no responsibility for any injury sustained whilst

handling hot ceramics. Ceramics which are found to be placed other than in

accordance with these instructions will result in a charge being made following

any service callout. Replacement ceramics are available from your dealer.

Stage One

Position the two large coal matrixes on the

burner, on the Lincoln & Stamford Model only,

ensure that the clearance between the Front

Matrix ports and the front of the Rear Matrix is

15mm as measured from the centre of the Rear

Matrix.

Stage Two

Position the four separately packed coals in the

corresponding indentations on the front edge of

the coal bed. These 4 coals are larger and have

a flat area on one side which should be position

in the four indentations in the coal bed.

Flue Spigot Connection

Attach the supplied 150mm long flue spigot to the rear of the stove using the four

self tapping screws provided.

200704_3 10

Assembly - Positioning the Coals

Stage Three

Position a coal on each of the platforms on the

centre coal.

Stage Four

Place a coal on the end of either side resting

between the rear matrix and the front matrix.

Next to this place three more coals across the

gap between the front row of coal and the rear

matrix in the centre. Place two additional coals

on top of the two top coals left and right as

shown.

Stage Five

Place the final layers of coals carefully as

shown.

Once coal positioning is complete, the lid

should be re-attached to the stove.

Andere Handbücher für Lincoln

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Broseley Herd Handbücher

Broseley

Broseley York Midi Handbuch

Broseley

Broseley WINCHESTER Bedienungsanleitung

Broseley

Broseley Serrano 3 Bedienungsanleitung

Broseley

Broseley WINCHESTER Bedienungsanleitung

Broseley

Broseley Inset Ignite 6 Remote Handbuch

Broseley

Broseley Gas Q7 MK2 Handbuch

Broseley

Broseley Ignite 5 Handbuch

Broseley

Broseley York Grande Bedienungsanleitung

Broseley

Broseley 12B Handbuch

Broseley

Broseley Canterbury Bedienungsanleitung

Broseley

Broseley Canterbury Handbuch

Broseley

Broseley Evolution 5 MK2 Handbuch

Broseley

Broseley YORK Bedienungsanleitung

Broseley

Broseley THURCROFT Betriebsanleitung

Broseley

Broseley York Petite Bedienungsanleitung

Broseley

Broseley Canterbury Handbuch

Broseley

Broseley WINCHESTER Bedienungsanleitung

Broseley

Broseley WINCHESTER Handbuch

Broseley

Broseley YORK Bedienungsanleitung

Broseley

Broseley Evolution 5 Multi-fuel Handbuch

Broseley

Broseley Desire Handbuch

Broseley

Broseley Snowdon 30 Handbuch

Broseley

Broseley Canterbury Bedienungsanleitung

Broseley

Broseley GB09b Bedienungsanleitung

Beliebte Herd Handbücher anderer Marken

Arada

Arada Cassette Stove Bedienungsanleitung

HearthStone

HearthStone Stowe DV 8321 Fehlerbehebungshandbuch

Cattara

Cattara FAMILY Bedienungsanleitung

Stanley

Stanley Argon F500 OVAL Bedienungsanleitung

Avalon

Avalon B-VENT Bedienungsanleitung

Nordpeis

Nordpeis Vega Bedienungsanleitung

Exquisit

Exquisit EKC601-5 Bedienungsanleitung

Stanley

Stanley Oisin Oil MK II Betriebsanleitung

Thermocet

Thermocet Brookfield S/CC Bedienungsanleitung

HASE

HASE delhi Bedienungsanleitung

Vermont Castings

Vermont Castings Intrepid 2 Bedienungsanleitung

Italiana Camini

Italiana Camini CLASSICA Kurzanleitung

Avalon

Avalon Vashon Avanti DVS FS Bedienungsanleitung

Spartherm

Spartherm ambiente a1 Bedienungsanleitung

Dimplex

Dimplex MCFSTV12AU Bedienungsanleitung

Warmlite

Warmlite WL46040 Bedienungsanleitung

Regency

Regency Ultimate U39E Series Kurzanleitung

Barton

Barton FH-AMP8745 Technisches Dokument